• Journal of Advanced Marine Engineering and Technology
• /
• 제29권3호
• /
• pp.281-289
• /
• 2005

An experimental study on the heat transfer and friction characteristics of a fully developed turbulent air flow in a square channel with $45^{\circ}$ inclined ribs on one, two, and four walls is reported. Tests were performed for Reynolds number ranging from 7,600 to 24,900. The pitch-to-rib height ratio, p/e, was kept at 8 and rib height-to-channel hydraulic diameter ratio, $e/D_h$, was kept at 0.0667. The heat transfer coefficient and friction factor values were enhanced with the increase in the number of ribbed walls. Results of this investigation could be used in various applications of internal channel turbulent flows involving different number of roughened walls.

• 한국해안해양공학회지
• /
• 제6권4호
• /
• pp.397-403
• /
• 1994

레이놀즈수에 대한 투수층흐름 마찰계수의 관계식을 개발하고자 투수층수조 실험을 실시하였다. 사용된 투수층수조는 물이 거의 수평으로 흐르도록 유도하는 장치이다. 각 구간마다 수두의 변화로 한번의 실험으로 다양한 수리조건을 재현할 수 있는 포괄성을 갖고 있으며, 여러 조의 수리실험을 실시하였다. 보다 광범위한 수리조건을 재현하기 위하여 여러 크기의 골재를 사용하였고 유출량도 다양하게 송출하였다. 기존자료를 이용하여 형상계수 산정식을 개발하였으며, 금번 수조실험의 결과를 이용하여 레이놀즈수가 1부터 600까지의 조건에서 투수층흐름 마찰계수를 구하는 양해법 산정식을 개발하였다. 관측된 마찰계수의 분포경향을 고려하였을 때, 레이놀즈수가 600보다 큰 난류조건에서도 동일 산정식을 사용할 수 있으리라 기대된다.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.930-937
• /
• 2001

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• 대한토목학회논문집
• /
• 제9권1호
• /
• pp.53-62
• /
• 1989

점변일차원이층류(漸變一次元二層流)모델로서의 염수(塩水)쐐기형상(形狀)의 계산(計算)을 행함에 있어서 필요(必要)한 계면저항계수(界面低抗係數)의 평가수단(評價手段)에 대(對)하여 논(論)한다. 예(例)를 들면, 폭(幅)이 좁은 실험수로(實驗水路)에서 얻어진 염수(塩水)쐐기의 형상(形狀)에 의해 계면저항계수(界面低抗係數)를 역산(逆算)하는 경우는 실제(實際)의 하천(河川)에서는 무시(無視)할 수 있는 수로(水路)의 측벽(側壁)의 영향(影響)을 보정(補正)하지 않으면 안된다. 본연구(本硏究)에서는 이러한 점(點)을 고려(考慮), 정상(定常) 염수(塩水)쐐기의 형상(形狀) 및 계면저항계수(界面低抗係數)에 미치는 수로(水路)의 측벽(側壁)의 영향(影響)을 밝힌다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제29회 춘계학술대회
• /
• pp.297-302
• /
• 1999

Finite element analysis is peformed about the crack propagation in half-space due to sliding contact. The analysis is based on linear elastic fracture mechanics and stress intensity factor concept. The crack location is fixed and the friction coefficient between asperity and half-space is varied to analyze the effect of surface friction on stress Intensity factor for horizontal crack. The crack propagation direction is predicted based on the maximum range of shear and tensile stress intensity factor.

• 한국산학기술학회논문지
• /
• 제16권4호
• /
• pp.2868-2875
• /
• 2015

개수로의 흐름 특성을 결정짓는 중요한 요소 중 하나는 흐름의 저항을 나타내는 마찰속도와 마찰계수이다. 하지만 개수로 흐름에서는 그 중요성에도 불구하고 자유수면과 단면의 복잡함, 다양한 수리변수들에 의해서 완벽한 해석이 매우 어렵다. 마찰계수에 대한 연구는 경험적 실험결과에 의존하고 있으므로 손쉬운 적용이 쉽지 않다. 따라서 본 연구에서는 엔트로피 개념을 활용하여 새로운 마찰계수 산정 공식을 제안하고 공식의 정확성을 증명하기 위해서 사다리꼴과 사각단면을 가진 개수로 실험 자료를 사용하였다. 본 공식의 장점은 무엇보다도 개수로에서 정확한 값을 알기 어려운 에너지 경사 항을 사용하지 않는 것에 있다. 그리고 이론적 배경을 바탕으로 높은 정확성을 가진 마찰계수 f의 산정이 가능함을 보여주었다.

• 한국농공학회지
• /
• 제33권4호
• /
• pp.105-120
• /
• 1991

This study was performed to investigate the minimum safety factor of embankment in consideration of seismic coefficient by the psuedo-static analysis The variables were cohesion, the internal friction angle, angle of slope, height of seepage, height of embankment, depth of replacement The results obtained were compared with those by Fellenius method, simplified Bishop method and Janbu method. The results were summarized as follows: 1.The increasing rate of the minimum safety factor with the increasing of cohesion appeared larger in Fellenius method and Bishop method than in Janbu method. And that with the increasing of the internal friction angle appeared the lowest value in Janbu method. The minimum safety factor was influenced larger on the internal friction angle than on cohesion. 2.The variation of the minimum safety factor with the height of seepage at 0m and 5 m was nearly similar to Fellenius method, Bishop method and Janbu method. On the other hand, it was decreased suddenly at 25 m. 3.The minimum safety factor with the height of embankment was decreased remarkably under 10 m with the increasing of seismic coefficient. But, it was decreased slowly more than 10 m. As the height of embankment was low, the influence of cohesion appeared larger. 4.In heigher case of the depth of replacement, the phenomenon of reduction of the minimum safety factor appeared remarkably with seismic coefficient increased. And in lower case of the depth of replacement, the minimum safety factor was similar in Fellenius method and Bishop mehtod. But it appeared larger in Bishop method and Janbu method than in Fellenius method with the depth of replacement increased. 5.As the cohesion and the internal friction angle were large, the phenomenon of reduction of the minimum safety factor with the increasing of seismic coefficient appeared remarkably. Also, the influence of seismic coefficient in minimum safety factor appeared larger with the soil parameter increased. 6.When the seismic coefficient was considerated, investigation of the structural body on the slope stability appeared profitably in Fellenius method and Janbu method than in Bishop method.

• 설비공학논문집
• /
• 제14권3호
• /
• pp.231-239
• /
• 2002

Experiments on the single phase cooling heat transfer and pressure drop with microfin tubes were performed using water as a test fluid. Experimental data were obtained in the range of Reynolds number 3000 ~40000 and Prandtl number 4-6. The data of microfin tubes presented the characteristics of rough surface tube in pressure drop and heat transfer Experimental data were compared with the heat transfer and friction factor correlations of smooth tubes. Heat transfer enhancements of microfin tubes were lower than pressure drop penalty factors. The helix angle is more significant parameter in both of the pressure drop and heat transfer than the relative roughness. The correlations of Nusselt number and friction factor were suggested for the tested microfin tubes. Maximum deviations between correlations and experimental data were within $\pm15$% for Nusselt number and $\pm10$% for friction factor.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.17-24
• /
• 2005

Recently construction activities increase in reclaimed onshore areas. It is therefore considered an important factor for the design of pile foundation with problems in terms of settlements due to soft grounds. Nevertheless the design of piles for negative skin friction(or downdrag forces) is probably poorly understood by many engineers. It is mainly because the most of design specification give a way to design pile foundation in bearing capacity aspect although the negative skin friction is related to settlement(downdrag). Under LRFD(load resistance factor design) approach it is to separately consider ultimate limit state and serviceability limit state. This paper discusses LRFD approach to the design of piles for negative skin friction and compares this approach to traditional design approach. And also a case history is analyzed in that point of view.

• 에너지공학
• /
• 제16권1호
• /
• pp.7-14
• /
• 2007

본 연구는 핀-관 열교환기의 건표면과 습표면 조건에서의 공기측 열전달 및 마찰특성을 실험을 통해 이해하고자 수행하였다. 핀-관 열교환기의 성능평가 및 해석기술을 확보하기 위하여 공기엔탈피식 칼로리 미터를 이용하였다. 핀형상은 슬릿과 평판이며, 관경은 7.0mm로 2열과 3열 핀-관 열교환기 4종에 대해 실험하여, 건표면과 습표면의 공기측 열전달 및 마찰특성을 조사하였다. 습표면에서 습도변화(RH 50%, 70%)에 따른 습도영향도 조사하였다. 건표면 조건에서 Re 수가 증가할수록 j 계수는 감소하며, 2열이 3열보다 높았다. 마찰계수는 슬릿 핀이 평판 핀보다 높았다. 습표면 조건에서 슬릿 핀이 평판 핀보다 그리고 2열이 3열보다 우수한 열전달효과를 나타내었다. j 계수와 마찰계수는 습도변화, 열수, 핀 형상에 따라 달라짐을 확인하였다.