• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1957-1964
• /
• 1997

Torsional vibration is to vibrate strongly when the ignition pulses of the engine is excited with natural frequency of driveline. Torsional vibration like this can cause various noises as rattle and booming. For this study multi-degree of freedom analysis model of torsional vibration, which is combined with mass moment of inertia and torsional spring, was developed toward two wheel drive, four wheel drive and torsional vibration characteristics were compared and analyzed through the natural frequences, mode shapes and frequency response characteristics which was acquired by the simulation of it. The pertinence of that model was proved by the field test and the outcome of the simulations coincided with feeling test. Therefore, four wheel drive simulation model is considered to be useful thing for reducing torsional vibration of driveline and developing full-time four wheel drive vehicles.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.460-470
• /
• 2015

In general ships and FPSOs, roll damping is very small and consequently roll motion is very large at the roll resonance frequency. Proper evaluation of the roll damping coefficient at the resonance frequency is an important task in the study of roll motion and usually it is done by the analysis of free roll decay tests. The relative decrement method based on energy relation has been used mainly for the evaluation of roll damping coefficient from the roll decay test so far. As another method, the logarithmic decrement method based on equivalent linear decay assumption can be used for the same purpose and it is relatively simple. In this paper, both of the relative decrement method and the logarithmic decrement method are used for the evaluation of roll damping coefficient including quadratic damping from the free roll decay tests, and their results are cross-checked for verifying the obtained damping coefficients. Through applications to a box-type floating body equiped with bilge keels, it is shown that the two methods give almost the same damping coefficients in a practical view point and the cross-check of their results is to be a good tool to prevent a possible error. And also the quantitative effects of the bilge keels on the roll damping of box-type floating body are shown and discussed.

• Journal of Power System Engineering
• /
• v.15 no.2
• /
• pp.13-18
• /
• 2011

This thesis is about the result of conducting a specific experiment for the development of noncontact vibration displacement sensor for measuring the spindle vibration that is used for conditional monitoring of machinery. One should be careful when using the eddy current type displacement sensor because the sensitivity of it is different according to the quality of the material. While the probe used for nondestructive inspection adopts the effect of transmitting the material by using the high frequency domain, the eddy current type displacement sensor uses the lower frequency of around 1MHz. Also, while the nondestructive probe uses the method of enhancing output by using the resonance zone, the vibration displacement sensor utilizes the stable zone by avoiding the resonance zone. Since the oscillator of the converter uses the "L" element as Probe, its characteristic changes with the variation of a relevant impedance. In other words, if the length of Probe's Cable gets extended (Impedance increase), the sensitivity declines accordingly. The effect of surrounding temperature was small, but the influence of the quality of Sensor Coil used was high. Moreover, following an experimental demonstration of the phenomenon where the sensitivity decreases as the frequency of the tested material increases from a frequency response test, the maximum frequency that could be measured was approximately 1KHz. It was noted that the degree of precision could be maintained by using the gap of the probe in the linear zone at the installation site.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.95-104
• /
• 2003

This paper deals with the analytic and FEM analyses of sloshing frequency response of incompressible, invicid and irrotational flow in two dimensional rectangular tank. We use Laplace equation based on potential theory as governing equation. For small amplitude sloshing motion, the linearized free surface condition was applied and the analytic solution as obtained by the separation of variables. To simulate the effect of the energy dissipation due to viscous damping, artificial viscous coefficient is introduced and the divergence of response at resonance frequencies may be avoided by this coefficient. This problem was solved by FEM using 9-node elements in order to predict the maximum amplitude of sloshing response. Numerical results of free surface height, fluid pressure and fluid force show good agreement with those by analytic solution. After verifying the test FEM program, we analyze the frequency response characteristics of sloshing to the fluid height.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.17 no.3
• /
• pp.205-211
• /
• 2001

The aim of this investigation was to evaluate successfully functioning implants stability in the partially edentulous mandibular molar sites by resonance frequency measurements. Resonance frequency measurement is more objective and clinically non-invasive method than any other methods had been used. In this study, $Osstell^{TM}$ (Integration Diagnostics, Sweden) was used. 15 patients ( 7 males, 8 females ) were received each 2 implants in their mandibular unilaterally partial edentulous molar sites. Total 30 implants were installed, 28 implants were $Br{\aa}nemark^{(R)}$ self-tapping fixtures(MK II, Nobel Biocare, Sweden) and 2 were $3i^{(R)}$(USA) self-tapping fixtures. Minimum of functional loading durations was 12 months and there were no significant marginal bone resorptions and peri-implant problems. From this test, the following results were drawn: 1. Mean ISQ values of implants in the first and second mandibular molar area were $73.66{\pm}4.45$, $71.93{\pm}3.41$, respectively. There was no significant difference between two groups(p>0.05). Also mean ISQ value of total sum was 72.8. 2. Mean ISQ values of implants in males and females group were $71.64{\pm}4.06$, $73.81{\pm}3.76$, respectively. And there was no significant difference between two group(p>0.05). 3. Correlation between implant lengths and ISQ values was weak(r=0.128).

• Phonetics and Speech Sciences
• /
• v.9 no.1
• /
• pp.49-53
• /
• 2017

Formant frequencies depend on the position of tongue, the shape of lips, and larynx. In the auditory system, the external ear canal is an open-end resonator, which can modify the voice characteristics. This study investigates the effect of the real ear on formant frequencies. Fifteen subjects ranging from 22 to 30 years of age participated in the study. This study employed three corner vowels: the low central vowel /a/, the high front vowel /i/, and the high back vowel /u/. For this study, the voice of a well-educated undergraduate who majored in speech-language pathology, was recorded with a high performance condenser microphone placed in the upper pinna and in the ear canal. Paired t-test showed that there were significant difference in the formant frequencies of F1, F2, F3, and F4 between the free field and the real ear. For /a/, all formant frequencies decreased significantly in the real ear. For /i/, F2 increased and F3 and F4 decreased. For /u/, F1 and F2 increased, but F3 and F4 decreased. It seems that these voice modifications in the real ear contribute to interpreting voice quality and understanding speech, timbre, and individual characteristics, which are influenced by the shape of the outer ear and external ear canal in such a way that formant frequencies become centralized in the vowel space.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.1983-1989
• /
• 2012

This paper presents the stability analysis of UH-60 helicopter with external store such like chaff/flare dispenser. An external store can affect the natural frequency of the aircraft and induce the resonance, which cause the failure of structures. In this paper, therefore, Rayleigh method is used to investigate the resonance with aircraft and external store, and transmission formula is used to determine the vibration load. Structural analysis with local modeling method are performed to present the robust design of aircraft with external store. The ground and flight test are also done to verify the stability of the aircraft.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.394-399
• /
• 2005

A case history is presented pertaining to high frequency piping vibration and noise caused by globe valve in the spent fuel pool cooling system of nuclear power plant. Frequency analyses were performed on the system to diagnose the problem and develop a solution to reduce the piping vibration and noise. The source of the high frequency and noise energy was traced to the globe valve located immediately downstream of the centrifugal pump by performing valve throttling test. Measurements of vibration and noise are presented to show that the high frequency vibration and noise amplitude was dependent upon the valve disc position and flow rate. Strouhal vortex shedding frequencies were generated at the exit of the globe valve which exited structural resonance of valve disc and amplified the high frequency vibration and noise. The problem was identified as an interaction between the flow inside globe valve and the valve disc structure. Attempts to reduce the vibration and noise amplitudes of the piping system were successfully achieved by the modification of guide-disc diameter and disc-edge figure The valve disc was replaced by an alternative to eliminate the source of the harmful high frequency vibration and noise.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.3
• /
• pp.176-182
• /
• 2021

This research proposes a high-frequency circuit that can accurately predict the differential mode noise of single-phase inverters at the circuit design stage. Proposed single-phase inverter high frequency circuit in the work is a form in which harmonic impedance components are added to the basic single-phase inverter circuit configuration. For accurate noise prediction, parasitic components present in each part of the differential noise path were extracted. Impedance was extracted using a network analyzer and Q3D in the measurement range of 150 kHz to 30 MHz. A high-frequency circuit model was completed by applying the measured values. Simulations and experiments were conducted to confirm the validity of the high-frequency circuit. As a result, we were able to predict the resonance point of the differential mode voltage extracted as an experimental value with a high-frequency circuit model within an approximately 10% error. Through this outcome, we could verify that differential mode noise can be accurately predicted using the proposed model of the high-frequency circuit without a separate test bench for noise measurement.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.7
• /
• pp.685-692
• /
• 2009

Vehicle interior noise is the results of numerous sources of excitation. One source involving tire pavement interaction is the tire cavity resonance and the forcing it provides to the vehicle spindle. Using a simplified model for the tire acoustic cavity system only, we formulated finite element equation to predict the fundamental acoustic cavity resonant characteristics inside tire-wheel assembly of undeformed and deformed tire. Combining the finite element analysis with experimental verification, we explained the acoustic characteristics theoretically. Especially, we have shown that the difference between the first two resonant frequencies increases as the deformation of deformed tire increases.