• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국작물학회지
• /
• 제4권1호
• /
• pp.115-124
• /
• 1968

1. 양마의 섬유중 단일반응성 엽형 경색 엽병색 삭과색에 관한 제형질에 대하여 개개의 질적형질의 유전 및 그들의 연소를 연구하였다. 량적형질의 유전은 통계유전학적방법을 이용하여 유전인자분석을 하였다. 또 이들 양적형질의 질적형질과의 연소 및 양적형질상호간의 연소를 조사하여 얻어진 지견을 응용하여 선발의 효과를 높이려고 하였다. 2. 본실험에는 양마의 품종 Dashkent, G38F-1의 1교잡을 사용하였다. Dshkent는 우리나라 재래품종으로 경색은 녹색이고 열핵엽형 녹색엽병색 개화일수는 10시간 단일처리하에서 106.9222일이고 호외 포장조건에서 105.8234일이었고 개체당 섬유중은 26.4922 gr였다. G38F-1은 Guatemala에서 도입하여 계통선발된 품종로서 적색경 수원엽형 적색엽병색 개화일수는 10시간단일처리하에서 62.3784일이고 호외포장조건에서 148.8921일였고 개체당 섬유중은 37.1591 gr.였다. 본교잡에 사용된 실험재료는 P, $P_2$, $F_2$, $F_2$, $BC_1$,($F_2$ ${\times}$ Dashkent), $BC_2$($F_2$ ${\times}$ G38F-1)의 각집단이며 1965년 수원작물시험장 포장에 재식하였다. 3. 엽형 엽병색 경색 삭과색 등 제형질의 유전은 수원엽형 녹색엽병 녹색경 녹색삭과등의 제인자가 단인자로서 그의 대립형질인 열각엽형 적색엽병 적색경 황색삭과에 대하여 각각 열성으로서 3:1의 Mendel성단순분리비를 나타내었다. 또 $F_1$과 열성형질과의 여교잡은 각각 1:1의 분리비가 인정되었다. 엽병색(G)과 엽형유전자(L)와의 조환가는 11.9565의 상인연소현상을 보였다. 삭과색(Y) 경색(R) 유전자간에는 어느것이나 연소현상이 보이지 않았다. 4. 단일반응성의 변이는 연소적이며 우성은 거의 인정되지 않았고 인자간의 상호작용도 인정되지 않았으며 상가적 유전을 보였다. 광의와 협의의 유전력은 각각 89.50%로서 실용적으로 대단히 높은 것으로 생각되었으며 단일반응성에 관여하는 유전자수는 2대의 인자로 추정하였고 다시 양친의 유전자형을 aabb AABB라고 측정하여 각인자의 작용가는 11.136일로 산출되었고 분해법에 의한 유전분석결과 유전자형의 관찰빈도분포와 이론빈도분포는 서로 잘 적합되었다. 단일반응성에 있어서 유전력이 대단히 높았으므로 비교적 초기세대에서 본 형질의 선발이 가능할 것 같았다. 5. 단일반응성과 엽형 및 엽병색 유전자와의 사이에 $F_2$, $BC_1$ 및 $BC_2$에서 각각 유의적인 상관관계를 볼 수 있었으므로 이들 형질간에 연소가 있는 것으로 인정되었다. 더욱 엽형과 엽병색과의 연소가 있는 것으로 인정되는 이상단일반응성 유전자와의 사이에 연소군이 인정된다. 6. 섬유중 유전자와 엽병색 및 엽형유전자와의 사이에 $F_2$$BC_1$ 및 $BC_2$에서 각각 유의적 상관관계를 볼 수 있었으므로 이를 형질간에 연소가 있는 것으로 인정되었다. 더욱 엽형과 엽병색과의 연소가 있는 것으로 인정되는 이상 섬유중 유전자와의 사이에 연소군이 인정된다. 7. 경장 경경 개화일수와 주당섬유중의 유전상관과 표현형상관에 있어서 전반적으로 표현형상관보다도 유전상관의 절대치가 크게되는 경향을 나타내었으며 식물체의 크기에 가장 밀접한 관계가 있는 경장 개화일수와 섬유중 형질상호간의 상관이 높은 치를 보였다. 8. 이상의 유전분석 결과 엽형 및 엽병색과 단일반응성경장 섬유중 형질간에는 연소 혹은 다면발현(pleiotropic effect)이 관여하는 것으로 이해하드라도 대과없는 것으로 생각되었고 양마에 있어서 고섬유중을 위한 선발은 엽병색 및 경장의 선발과 엽형 및 개화일수로서 선발을 함께 하면 그 효율이 높아질 것으로 믿어졌다.

• 한국작물학회지
• /
• 제17권
• /
• pp.1-44
• /
• 1974

본연구는 1972년에 수원에서 그리고 1973년에는 다시 수원, 매리 및 이리 광주의 3개 지역에서 경질 소맥인 NB 68513, Caprock와 중간질 소맥인 영광, 연질 소맥인 수계 169호를 공시하여 시비량 및 재배시기를 각각 3수준의 처리를 두어 등숙 및 품질의 변화에 관한 실험을 수행하였다. 한편 1973년 및 1974년에는 수원에서 중간질 소맥인 영광과 경질 소맥인 NB 68513을 공시하고 온실에서 온도, 습도 및 일사량을 달리하여 이들이 소맥의 등숙과 품질에 미치는 영향을 추구하였으며, 얻어진 결과는 다음과 같다. 1. 소맥립의 등숙: 1) 1립중의 변이폭은 대립종이 소립종에 비하여 크고, 립중별 소맥립의 분포는 대립종이 평균치에 가까이 분포된 율이 높았고, 소립종은 넓은 분산을 보였다. 2) 립중의 증가에 미치는 립장, 립후 및 립폭의 영향의 정도는 립장보다 립후와 립폭이 컸다. 3) 등숙 시기별 립중의 변화에 있어서 영광은 개화후 14일부터 35일까지, NB 68513은 14일부터 28일까지에 급증하였고, 대립종인 영광은 소립종인 NB68513에 비하여 등숙기간이 길었으며 배란비율도 완만한 증가를 보였다. 4) 1000립중은 대체로 저온에서보다 고온에서, 다습보다 건조한 공중습도 조건에서 가벼웠고, 저온이나 고온에서라도 다습 조건하에서는 무거운 경향을 보였다. 또한 서광의 영향은 저온에서보다 고온에서 컸으며, 다습한 경우에는 일정한 경향이 없었다. 5) 등숙기간중 온도, 습도 및 서광의 영향은 소립종인 NB 68513보다 대립종인 영광에서 컸으며, 1000립중의 증감과 등숙일수 간에는 높은 정의 상관이 있었다. 6) 1000립중과 1$\ell$중은 시비량의 증가에 따라 무거워졌으나, 보비와 다비구간에는 그 증가율이 비교적 낮았고, 조숙재배는 만파재배보다 무거웠으며, 이와 같은 경향은 수원에서 현저하였고 광주 및 이리에서는 미미하였다. 2. 제분성: 7) 동일 품종에서 1000립중이 무겁게 나타난 저온다습 조건 및 조숙재배가 고온, 건조, 조건 및 만파재배에 비하여 제분율이 높았고, 지역간 차이는 일정한 경향이 없었다. 8) 제분율은 영광이 가장 높고 수계 169호가 가장 낮았으며, 경질 소립종인 Caprock, NB 68513은 연질 소립종인 수계 169호보다 높았다. 9) 회분 함량은 지역, 시비량 및 재배시기에 따른 차이는 작았고, 품종간 차이는 컸으며, NB 68513 및 Caprock는 영광 및 수계 169호보다 현저히 높았다. 3. 단백질 함량: 10) 단백질 함량은 1000립중이 가벼웠든 고온, 건조 및 서광 조건에서 저온, 다습 조건에서보다 높았으며, 이러한 경향은 영광에서 현저하고 NB 68513에서 적었다. 11) 종질의 단백질 함량은 개화후 1~2주일 사이에 높았는데, 이는 배란에 대한 배와 종피의 비율이 크기 때문이었고, 등숙이 진전됨에 따라 배, 종피의 영향은 감소되며, 달서 단백질 함량도 감소되었으나 개화후 3~4주부터는 다시 단백질함량이 증가되어 개화후 7주에 최대에 달하였다. 등숙 중기(개화후 3~4주) 이후의 단백질함량 증가는 대체로 1000립중의 증가와 비슷하였으나, 성숙된 종실의 단백질 함량의 증감은 등숙기간의 장단의 영향보다는 역일상에 따른 기상적 환경, 특히 기온에 의한 영향을 많이 받은 것으로 보였다. 12) 소맥분의 단백질 함량은 종실의 단백질 함량의 변화와 같아서 이 양자간에는 높은 정의 상관이 있었다. 13) 단백질 함량은 각 품종 모두 시비량이 증가할수록, 또 재배시기가 늦어질수록 증가하는 경향이었고, 수원에서는 광주, 이리에서보다 그 경향이 현저하였다. 14) 품종별로 존 단백질 함량은 영광, NB 68513 및 Caprock은 비슷하였으며 비교적 높았고, 수계 169호는 낮았는데 이 품종은 재배법에 따른 단백질 함량의 변이도 적었다. 15) 단위 면적당 단백질 수량은 시비량이 많을수록, 재배시기가 빠를수록 높은 경향이었고, 조숙재배에서는 질소질 비료의 이용율이 높았으며, 영광은 시비량 증가에 따른 단백질 수량 증가가 비교적 컸다. 4. 분의 물리화학적 특성: 16) Sedimentation value는 저온, 다습, 소비 조건에서보다 고온, 건조, 다비 조건에서 컸고, NB 68513 및 Caprock는 그 경향이 현저하였는데 영광 및 수계 169호는 뚜렷하지 않았었고, 광주, 이리보다는 수원에서 Sedimentation value의 변이가 컸다. Sedimentation value의 증감은 단백질 함량의 증감과 관계가 깊으나, 다습조건에서는 Sedimentation value가 감소되었다. 한편 Sedimentation value는 단백질 함량의 증가에 따라 증가되었으며, 성숙기에 최대에 달하였다. 17) Pelshenke value는 재배방법 및 지역 간의 차이가 Sedimentation value의 경우와 대체로 같은 경향을 보였다. 18) Mixing time은 NB 68513이 4~6분, Caprock가 5~7분 소요되었으며, 영광 및 수계 169호는 NB 68513 및 Caprock보다 지역 및 재배법에 따른 변이가 컸다. Mixing height와 Mixing area는 NB 68513 및 Caprock에서 컸고 영광 및 수계 169호에서는 작았으며, 재배방법에 따른 변이는 일정한 경향이 없었고, 지역에 따른 차이는 이리, 광주에서 낮고 수원에서 높았다. 19) NB 68513 및 Caprock의 품질에 있어서 제분성은 고온, 건조 조건, 또는 다비, 만파재배에서 떨어졌으나 분의 물리화학적 특성은 양호하여 제빵 적성이 좋고, 조숙재배는 물리화학적 특성이 다소 불량하였으나 제분성이 높고 단위 면적당 단백질 수량인 높은 경향이었다. 지역간에서 보면 이리, 광주보다는 수원이 NB 68513 및 Caprock의 재배에 적합한 것으로 판단되었다. 5. 분의 물리화학적 특성의 상호관계: 20) 제분율 및 회분함량과 분의 물리화학적 특성과는 직접적인 상관이 없었으며, 1000립중이 가벼운 것이 단백질 함량이 높았고 분의 물리화학적 특성도 양호하였다. 21) NB 68513 및 Caprock에 있어서 단백질 함량과 Sedimentation value, Pelshenke value 및 mixing height와는 정의 상관이 있었으며, 단백질 함량이 높으면 분의 Gluten strength도 강하고 따라서 제빵 적성도 양호하였다. 영광 및 수계 169호에 있어서는 단백질 함량과 Sedimentation value와는 정의 상관이 있으나 Pelshenke value와 Mixing height와는 상관이 없었다. 따라서 단백질 함량 증가에 따라 Gluten strength 양자와 연결됨이 크고, Pelshenke value와 Mixogram은 Gluten strength와 연관됨으로 경질과 연질의 품종 구분에는 Mixogram, Pelshenke value의 검정이 유리하고, Sedimentation valuer검정은 같은 품종내에서 재배법 차이에 따른 품질 평가에 알맞은 것으로 보았다.

• Applied Biological Chemistry
• /
• 제16권2호
• /
• pp.99-111
• /
• 1973

전국적(全國的)으로 실시한 삼요소(三要素) 시험중(試驗中) 1967년(年) 51개소(個所) 68년(年)에 32개소(個所)에서 N 8, 10, 12, 14kg/10a 수준(水準)과 $P_2O_5$ 및 $K_2O$ 각(各) 6과 8kg 시비수준(施肥水準)에 대(對)한 삼요소(三要素) 이용율(利用率)을 조사(調査)하였다. 삼요소(三要素) 이용율(利用率)과 수량(收量) 및 건물생산량(乾物生産量), 삼요소(三要素) 및 규산흡수량(珪酸吸收量)과의 아래와 같은 관계에서 무기양분(無機養分)의 생산(生産)에 기여하는 양상(樣相)이 시용(施用)한 P가 1차적(次的)으로 Si흡수(吸收)를 이차적(二次的)으로 Si가 N흡수(吸收)를 조장(助長)하여 기여하는 P형(型)과 시용(施用)한 K가 P흡수(吸收)를, 이차적(二次的)으로 P가 N흡수(吸收)를 조장(助長)하여 기여하는 K형(型)으로 연도별(年度別) 주도형(主導型)을 구분(區分)할 수 있었다. 1. 질소(窒素)는 전포장수(全圃場數)의 4%, 인산(燐酸)은 48%, 가리(加里)는 38%가 0 또는 부(負)의 이용율(利用率)을 보였으며 이용율(利用率)의 발현빈도(發現頻度) 백분분포(百分分布)가 N는 30 내지 40에서 최고빈도(最高頻度)를 보이는 정규분포(正規分布)에 가깝게, P와 K는 0 이하(以下)에서 최고빈도(最高頻度)를 갖고 점차 감소하는 편의 분포(分布)를 갖는다. 2. 삼요소(三要素) 이용율(利用率) (0 이상(以上)만)은 67년(年)에 N는 33(10kg 시비(施肥) 수준이상(水準以上)) P는 27, K는 40이고 68년(年)엔 40, 20, 46%이고 부(負)의 이용율(利用率)을 0으로한 2개년(個年) 평균(平均)은33(8kg 이상(以上)) 13, 27이었다. 3. 이용율(利用率)의 표준편차(漂準偏差)는 P와 K에서 이용율(利用率)보다 크고 P이용율(利用率)의 변이(變異)가 가장 크다. 4. 이용율(利用率)과 수량(收量) 또는 건물생산량(乾物生産量)과의 유의상관(有意相關) 출현빈도(出現頻度)는 N>K>P의 순(順)이며 10kg 수준의 N이용율(利用率)은 67년(年)엔 P이용율(利用率)과만 63년(年)엔 K이용율(利用率)과만 유의상관(有意相關)을 갖는다. 5. P이용율(利用率)은 그것이 높고 K이용율(利用率)이 낮았던 67년(年)에만, 그리고 K이용율(利用率)은 그와 반대였던 68년(年)에만 모든 처리구의 건물생산량(乾物生産量)과 유의상관(有意相關)을 보이고, 유의상관(有意相關)이 없는 해에는 무비구(無肥區) 및 결비구(缺肥區)區에서 부상관계수(負相顯係數)를 보이고 있다. 6. 이용율(利用率)과 수량(收量)과의 상관(相關)은 이용율(利用率)과 건물생산량(乾物生産量)과의 상관(相關)과 경향은 유사하나 유의성이 적어삼요소(三要素) 영양(營養)은 건물생산(乾物生産)에서 잘 표현된다. 7. N이용율(利用率)은 N시비구(施肥區)의 N흡수량(吸收量)과 많은 경우 유의상관(有意相關)을, 무(無)N구(區)의 흡수량(吸收量)과는 유의부상관(有意負相關)을 보이며, N시비구(施肥區)의 P, K또는 Si흡수량(吸收量)과도 여러 경우 유의상관(有意相關)을 보였다. 8. P이용율(利用率)은 그것이 높았던 67년(年)만 모든 처리구에서 Si흡수량(吸收量)과, 그리고 무(無)P구(區)를 제(除)한 모든 처리구의 N 흡수량(吸收量)과 유의상관(有意相關)을 보여 P는 일차적(一次的)으로 Si흡수(吸收)를 돕고 이차적(二次的)으로 Si흡수(吸收)가 N흡수(吸收)를 조장(助長)함을 나타낸다. P이용율(利用率)은 N시비구(施肥區)의 P흡수량(吸收量)과 K흡수량(吸收量)과도 많은 경우 유의상관(有意相關)을 보였다. 9. K이용율(利用率)은 그것이 컸던 68년(年)에 모든 처리구의 P흡수량(吸收量)과 무(無)N구(區)을 제(除)한 모든 처리구의 N흡수량(吸收量)과 그리고 무(無)P구(區)를 제(除)한 모든 처리구의 K흡수량(吸收量)과 유의상관(有意相關)을 보이며 무(無)K구(區)의 K흡수량(吸收量)과는 부상관(負相關)이고 K이용율(利用率)이 적었던 67년(年)에는 무비구(無肥區)나 결비구(缺肥區)의 P흡수량(吸收量)과 유의성(有意性)은 없으나 부상관(負相關)이었다. K이용율(利用率)은 N나 P와는 달리 K흡수량(吸收量)과 보다 수량(收量)이나 건물생산량(乾物生産量)과의 상관(相關)이 더 크며 K이용율(利用率)이 컸던 해에만 Si흡수량(吸收量)과 무(無)N구(區)와 최고시비구(最高施肥區)에서 유의상관(有意相關)을 갖고 무(無)K구(區)에서 유의부상관(有意負相關)을 보였다. 이로서 K는 일차적(一次的)으로 P흡수(吸收)를 돕고 이차적(二次的)으로 P가 N흡수(吸收)를 도와서 생산(生産)에 기여하는 것 같다. 10. N이용율(利用率)과 수량(收量)이나 건물생산량(乾物生産量)과의 상관(相關)이 무(無)P구(區)에서 보다 무(無)K구(區)가 높고 무(無)K구(區)보다 시비구(施肥區)에서 높으며 이러한 경향은 N이용율(利用率)과 N흡수량(吸收量)사이에서도 동일(同一)하였다. 이 사실과, K이용율(利用率)과 건물생산량(乾物生産量)과의 관계는 P가 N흡수(吸收)를 돕고 N나 P가 부족(不足)할 때에는 K가 N흡수(吸收)를 경쟁적으로 억제하여 생산(生産)을 저하(低下)시키는 것을 나타낸다. 11. 삼요소(三要素) 이용율(利用率)은 67년(年)에는 무(無)P구(區)의 상대건물생산량(相對乾物生産量)과, 68년(年)에는 무(無)K구(區)의 상대수량(相對收量)과 유의상관(有意相關)을 갖는다. 이는 P가 분얼 즉 영양생장단계에, K가 곡실형성 즉 생식 생장단계에 더 작용(作用)하였음을 나타내고 있다. 12. 삼요소(三要素) 이용율(利用率)과 결비구(缺肥區)의 상대생산량(相對生産量)이나 무비구(無肥區)의 결비구(缺肥區)에 대(對)한 상대생산량(相對生産量)과의 상관(相關)에서 어느 경우에도 N가 수도생산(水稻生産)에 가장 큰 역할(役割)을 하고 있음을 보였다. 13. 이상의 결과에서 40 내지 50%의 포장(圃場)은 P와 K를 시비(施肥)하지 아니해도 되며 시비량(施肥量)도 연도(年度)및 포장에 따라 변이(變異)가 커야 할 것이며 특히 P에서 그러하다.

• Journal of Animal Science and Technology
• /
• 제45권6호
• /
• pp.1067-1078
• /
• 2003

산차가 다른 임신모돈의 임신기간 동안 스톨수용과 군사수용이 임신, 분만 및 비유기간 중 모돈의 행동패턴과 이상반복행동 및 분만성적에 미치는 영향을 조사하기 위하여 총 18두의 듀록(Duroc)종 모돈을 산차별로 1산차, 2${\sim}$3산차 및 4${\sim}$5산차 각각 3두씩 배치하여 임신초기 4주간은 스톨에 수용 후 각각 스톨과 군사돈방에 수용하였고, 분만예정일 7일전에 분만돈방으로 옮겼으며 21일간 포유로 수행하여 얻은 성적은 다음과 같다. 임신기간 동안의 모돈 행동패턴과 이상반복행동은 임신 60일과 90일 경과 시점에 24시간 동안, 분만당일 모돈 행동은 분만 2시간 전부터 후산이 배출되는 시점까지 약 6시간 동안, 비유기간 동안의 모돈 행동은 분만 10일 후, 2시간 반 동안 조사하였다. 또한 임신기간 동안 군사수용과 스톨수용 모돈의 분만성적을 비교하였다. 임신기간 동안 군사수용과 스톨수용 모돈의 행동은 옆으로 누워(ventral lying)있는 시간 비율이 양쪽 모두 가장 높았고, 산차에 따라서는 초산 모돈(71.3%)이 가장 높았다. 걷는(walking) 동작은 스톨수용 보다 군사수용이 월등히 높게 나타났고(8.68% 대 16.38%, SE=1.74; P<0.01), 산차 간에는 초산 모돈이 가장 낮았다. 마시는 (drinking) 동작으로 보낸 시간 비율은 군사수용 보다 스톨수용(0.27% 대 1.99%, SE=0.28)이 월등히 높게 나타났다(P<0.01). 임신기간 동안 나타내는 이상반복행동 발현수는 헛 씹기(vacuum chewing)가 스톨수용 임신 60일 경과시 가장 높았고, 산차와 임신일 간의 상호작용에서는 4${\sim}$5산차 임신돈의 임신 60일 경과가 높았다(P<0.05). 코로 바닥 문지르기(floor snout rubbing)는 수용형태${\times}$산차의 상호작용이 나타났으며, 군사 1산차가 가장 높게 나타났다(P<0.05). 바닥 핥기(floor licking)는 임신 90일이 높았고(P<0.01), 수용형태$\times$임신일의 상호작용에서는 군사 90일이 높게 나타났다. 머리 흔들기(head waving)은 임신 60일이 높게 나타났으며, 쇠 핥기(bar licking)는 임신 90일이 높게 나타났다(P<0.05). 총 이상행동의 발현수는 스톨수용과 군사수용 간에 차이가 나타나지 않았다. 분만돈의 행동패턴은 앉아 있는 자세와 먹는 자세로 보낸 시간 비율만 유의적인 차이를 나타내었고, 앉아 있는 자세에서는 스톨수용 1산차(3.7%)와 군사수용 2${\sim}$3산차(2.7%)가 다른 산차 보다 높게 나타났다. 먹는 자세로 보낸 시간 비율은 군사 2${\sim}$3산차 만이 낮게 나타났다. 비유모돈의 행동패턴은 임신기간 동안 군사수용 1산차 모돈의 옆으로 누워 있는(ventral lying) 시간 비율이 높았고, 마시는(drinking) 동작은 임신기간 동안 스톨 수용 모돈이 높았으며, 특히 초산 모돈이 다른 산차의 모돈에 비하여 많은 시간을 물먹는데 소비하는 것으로 나타났다. 이상의 결과를 종합해 보면, 임신기간 동안 수용형태에 따른 임신돈의 임신기간 동안의 행동패턴과 이상반복행동 발현수의 차이는 나타나지 않았으나, 비유모돈의 행동패턴과 이상반복행동 발현에 대한 결과는 군사수용 모돈이 보다 좋은 복지 상태에 있다는 것을 나타내고 있다. 또한 분만성적이 임신기간 동안 스톨수용과 군사수용 간에 차이를 나타내지 않았다. 따라서 모돈의 보다 많은 정상행동을 보장하고 복지상태를 개선하기 위해서는 임신돈의 군사수용은 스톨수용을 대체할 사양체계로서 그 가능성은 충분하며, 실제 적용을 위한 보다 진전된 연구가 필요한 것으로 사료된다.

• The Korean Journal of Physiology
• /
• 제8권2호
• /
• pp.1-17
• /
• 1974

미로(迷路) 각반규관(各半規管)과 각외안근간(各外眼筋間)의 기능적(機能的) 관계(關係)를 구명(究明)하여 미로반사성(迷路反射性) 안구운동(眼球運動)을 위한 신경기구(神經機構)를 이해하고져 마취가토(麻醉家兎)에서 골성(骨性) 반규관(半規管) 팽대부내(膨大部內)에 단전극(單電極)을 삽입하여 각(各) 팽대부신경(膨大部神經)을 전기자극(電氣刺戟)하였을 때 양안(兩眼)의 각(各) 외안근(外眼筋)의 반응(反應)을 등장성장력변화(等長性張力變化)와 근전도(筋電圖)로써 관찰하여 다음과 같은 결론(結論)을 얻었다. 1) 일측(一側) 미로(迷路)에서 한 반규관신경을 자극하면 양안(兩眼)에서 각각(各各) 3개의 안근(眼筋)은 흥분(興奮)하여 수축(收縮)하고 여기에 대(對)한 3개의 길항근(拮抗筋)은 억제(抑制)되어 이완(弛緩)하였다. 2) 일측(一側) 미로(迷路)의 어느 반규관신경을 자극하거나 동측안(同側眼)에서는 상직근(上直筋), 상사근(上斜筋) 및 내직근(內直筋)이 흥분(興奮)(수축(收縮))하고, 하직근(下直筋), 하사근(下斜筋) 및 외직근(外直筋)은 억제(抑制)(이완(弛緩))되었다. 반대측(反對側) 근(筋)에서는 하직근(下直筋), 하사근(下斜筋) 및 외직근(外直筋)이 흥분(興奮)하고 상직근(上直筋), 상사근(上斜筋) 및 내직근(內直筋)은 억제(抑制)되었다. 3) 일측(一側) 미로(迷路)의 3개 반규관자극을 중복(重複)시켰을 때는 한 안근(眼筋)이나 각안근(各眼筋) 길항근대(拮抗筋對)에 각반규관신경(各半規官神經)의 자극효과(刺戟效果)가 중첩(重疊)됨을 증명(證明)할 수 있었다. 4) 이상(以上)의 실험적 근거를 토대로 하여 각반규관(各半規官)과 각외안근(各外眼筋)의 기능적(機能的) 관계(關係)를 규정(規定)하는 법칙성(法則性)을 찾을 수 있었다. 즉(卽) ‘상직근(上直筋), 내직근(內直筋) 및 상사근(上斜筋)은 동측(同側) 미로(迷路) 반규관(半規管)으로부터 흥분적(興奮的) 충격(衝擊)을 받고 반대측(反對側) 반규관(半規管)들로부터는 억제적(抑制的) 충격(衝擊)을 받으며, 하직근(下直筋), 외직근(外直筋) 및 하사근(下斜筋)을 위하여는 이와 정반대(正反對)의 관계(關係)가 성립(成立)한다. 5) 본(本) 실험성적(實驗性績)을 Cohen 등(等)의 가묘(家猫)에서의 연구보고(硏究報告)와 비교하건데 사근(斜筋)에 대(對)한 반규관사배(半規管司配)는 동일(同一)하나, 내(內) 및 외직근(外直筋)과 상(上) 및 하직근(下直筋)에 대(對)한 반규관사배(半規管司配)는 일부(一部) 상이(相異)하였다. Cohen 등(等)의 성적을 분석(分析)하여 본 결과 이론적(理論的) 모순(矛盾)이 있음을 보았고 안근(眼筋)의 각(各) 길항근(拮抗筋)에 대한 반규관사배(半規管司配)의 양식(樣式)에 있어 일정(一定)한 법칙성(法則性)을 찾을수 없었으며 그들의 관찰에는 실험적(實驗的) 오류(誤謬)를 포함하고 있음을 증명(證明)하였다.

• Journal of Animal Science and Technology
• /
• 제50권6호
• /
• pp.807-818
• /
• 2008

본 시험은 외인성 유산균의 장내 생존성과 유산균 첨가수준 및 급여빈도가 육계 생산성에 미치는 영향을 조사함으로써 유산균의 적정 급여방법을 구명하기 위하여 실시되었다. 시험 1에서는 외인성 유산균의 장내 체류 시간을 조사하기 위하여 5주령 육계(Abor Acre) 100수에서 사료 내 1.0×104cfu/g 수준으로 GFP 유전자가 도입된 유산균을 급여하였다. GFP 유산균을 육계에게 급여한 결과 급여 3일차까지는 일정한 수 이상의 유산균이 관찰되었으나 그 이후 급격히 감소되는 것을 확인하였다. 시험 2에서는 유산균 적정 첨가 수준을 구명하기 위하여 1일령 육계 수평아리(Abor Acre) 480수를 공시하여 4처리 4반복, 반복당 30수씩 임의 배치하여 5주간 사양시험을 실시하였다. 시험처리는 항생제 무첨가구를 대조구로 하였으며, 음수 내 유산균을 5.0×10cfu/mL, 5.0×103 cfu/mL, 및 5.0×105cfu/mL 수준으로 첨가하여 유산균 처리구를 두었다. 5주 종료 체중은 5.0×103cfu/mL 첨가 급여시 1,919g으로 가장 높았으며(P<0.05), 증체량은 5.0×103cfu/mL 및 5.0×105cfu/mL 첨가 급여시 대조구에 비해 유의하게 증가하였다(P<0.05). 회장 및 맹장 내 유산균 수에 있어서는 첨가수준별로 차이는 있었으나 유산균 첨가 급여시 회장 및 맹장 내 유산균 수가 유의하게 증가하였으며(P<0.05), 그 변화 양상은 회장과 맹장에서 유사하게 나타났다. 단백질 및 지방 이용율이 유의하게 증가하였다(P<0.05), 건물 및 조회분에 있어서는 처리간 차이가 관찰되지 않았다. 시험 3에서는 유산균 적정 급여 빈도를 구명하기 위하여 1일령 육계 수평아리(Abor Acre) 600수를 공시하여 5처리 4반복, 반복당 30수씩 임의 배치하여 5주간 사양시험을 실시하였다. 시험처리는 항생제 무첨가구를 대조구로 하였으며, 유산균이 5.0×103cfu/mL 수준으로 첨가된 음수를 1일, 2일, 3일 및 5일 간격으로 급여한 유산균 처리구를 두었다. 5주 종료체중 및 증체량에 있어서 유산균을 매일 또는 격일로 급여시 유의하게 증가하였다(P<0.05). 사료섭취량 및 사료요구율은 처리구간 차이가 없었다. 회장과 맹장내 유산균의 수는 유산균 급여시 전체적으로 증가하는 경향을 보였으며, 특히 매일 및 격일 급여시 유의하게 증가하였다(P< 0.05). Coliform bacteria 및 Salmonella 수에 있어서는 처리구간 차이가 없었다. 본 시험 결과, 유산균의 음수 내 첨가 급여는 육계 생산성 및 장내 미생물 균총에 긍정적인 영향을 미쳤으며, 유산균의 적정 첨가 수준은 음수 1ml 당 유산균 5.0×103cfu이었으며, 급여 빈도에 있어서는 매일 급여하는 것이 효과적인 것으로 판단된다.

• 화약ㆍ발파
• /
• 제9권1호
• /
• pp.3-13
• /
• 1991

발파에 의한 지반진동의 크기는 화약류의 종류에 따른 화약의 특성, 장약량, 기폭방법, 전새의 상태와 화약의 장전밀도, 자유면의 수, 폭원과 측간의 거리 및 지질조건 등에 따라 다르지만 지질 및 발파조건이 동일한 경우 특히 측점으로부터 발파지점 까지의 거리와 지발당 최대장약량 (W)간에 깊은 함수관계가 있음이 밝혀졌다. 즉 발파진동식은 $V=K{\cdot}(\frac{D}{W^b})^n{\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$ (1) 여기서 V ; 진동속도, cm /sec D ; 폭원으로부터의 거리, m W ; 지발 장약량, kg K ; 발파진동 상수 b ; 장약지수 R ; 감쇠지수 이 발파진동식에서 b=1/2인 경우 즉 $D{\;}/{\;}\sqrt{W}$를 자승근 환산거리(Root scaled distance), $b=\frac{1}{3}$인 경우 즉 $D{\;}/{\;}\sqrt[3]{W}$를 입방근환산거리(Cube root scaled distance)라 한다. 이 장약 및 감쇠지수와 발파진동 상수를 구하기 위하여 임의거리와 장약량에 대한 진동치를 측정, 중회귀분석(Multiple regressional analysis)에 의해 일반식을 유도하고 Root scaling과 Cube root scaling에 대한 회귀선(regression line)을 구하여 회귀선에 대한 적합도가 높은 쪽을 택하여 비교, 검토하였다. 위 (1)식의 양변에 log를 취하여 linear form(직선형)으로 바꾸어 쓰면 (2)式과 같다. log V=A+BlogD+ClogW ----- (2) 여기서, A=log K B=-n C=bn (2)식은 다시 (3)식으로 표시할 수 있다. $Yi=A+BXi_{1}+CXi_{2}+{\varepsilon}i{\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$(3) 여기서, $Xi_{1},{\;}Xi_{2} ;(두 독립변수 logD, logW의 i번째 측정치. Yi ; ($Xi_1,{\;}Xi_2$)에 대한 logV의 측정치 ${\varepsilon}i$ ; error term 이다. (3)식에서 n개의 자료를 (2)식의 회귀평면으로 대표시키기 위해서는 $S={\sum}^n_{i=1}\{Yi-(A+BXi_{1}+CXi_{2})\}\^2$을 최소로하는 A, B, C 값을 구하면 된다. 이 방법을 최소자승법이 라 하며 S를 최소로 하는 A, B, C의 값은 (4)식으로 표시한다. $\frac{{\partial}S}{{\partial}A}=0,{\;}\frac{{\partial}S}{{\partial}B}=0,{\;}\frac{{\partial}S}{{\partial}C}=0{\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$ (4) 위식을 Matrix form으로 간단히 나타내면 식(5)와 같다. [equation omitted] (5) 자료가 많아 계산과정이 복잡해져서 본실험의 정자료들은 전산기를 사용하여 처리하였다. root scaling과 Cube root scaling의 경우 각각 $logV=A+B(logD-\frac{1}{2}W){\;}logV=A+B(logD-\frac{1}{3}W){\;}\}{\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$ (6) 으로 (2)식의 특별한 형태이며 log-log 좌표에서 직선으로 표시되고 이때 A는 절편, B는 기울기를 나타낸다. $\bullet$ 측정치의 검토 본 자료의 특성을 비교, 검토하기 위하여 지금까지 발표된 국내의 몇몇 자료를 보면 다음과 같다. 물론, 장약량, 폭원으로 부터의 거리등이 상이하지만 대체적인 경향성을 추정하는데 참고할수 있을 것이다. 금반 총실측자료는 총 88개이지만 환산거리(5.D)와 진동속도의 크기와의 관계에서 차이를 보이고 있어 편선상 폭원과 측점지점간의 거리에 따라 l00m말만인 A지역과 l00m이상인B지역으로 구분하였다. 한편 A지역의 자료 56개중, 상하로 편차가 큰 19개를 제외한 37개자료와 B지역의 29개중 2개를 낙외한 27개(88개 자료중 거리표시가 안된 12월 1일의 자료3개는 원래부터 제외)의 자료를 computer로 처리하여 얻은 발파진동식은 다음과 같다. $V=41(D{\;}/{\;}\sqrt[3]{W})^{-1.41}{\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$ (7) (-100m)(R=0.69) $V=124(D{\;}/{\;}\sqrt[3]{W})^{-1.66){\;}{\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots\cdots}$ (8) (+100m)(R=0.782) 식(7) 및 (8)에서 R은 구한 직선식의 적합도를 나타내는 상관계수로 R=1인때는 모든 측정자료가 하나의 직선상에 표시됨을 의미하며 그 값이 낮을수록 자료가 분산됨을 뜻한다. 본 보고에서는 상관계수가 자승근거리때 보다는 입방근일때가 더 높기 때문에 발파진동식을 입방근($D{\;}/{\;}\sqrt[3]{W}$)으로 표시하였다. 특히 A지역에서는 R=0.69인데 비하여 폭원과 측점지점간의 거리가 l00m 이상으로 A지역보다 멀리 떨어진 B지역에서는 R=0.782로 비교적 높은 값을 보이는 것은 진동성분중 고주파성분의 상당량이 감쇠를 당하기 때문으로 생각된다.

• Asia pacific journal of information systems
• /
• 제21권2호
• /
• pp.89-116
• /
• 2011

In collaborative tagging systems such as Delicious.com and Flickr.com, users assign keywords or tags to their uploaded resources, such as bookmarks and pictures, for their future use or sharing purposes. The collection of resources and tags generated by a user is called a personomy, and the collection of all personomies constitutes the folksonomy. The most significant need of the folksonomy users Is to efficiently find useful resources or experts on specific topics. An excellent ranking algorithm would assign higher ranking to more useful resources or experts. What resources are considered useful In a folksonomic system? Does a standard superior to frequency or freshness exist? The resource recommended by more users with mere expertise should be worthy of attention. This ranking paradigm can be implemented through a graph-based ranking algorithm. Two well-known representatives of such a paradigm are Page Rank by Google and HITS(Hypertext Induced Topic Selection) by Kleinberg. Both Page Rank and HITS assign a higher evaluation score to pages linked to more higher-scored pages. HITS differs from PageRank in that it utilizes two kinds of scores: authority and hub scores. The ranking objects of these pages are limited to Web pages, whereas the ranking objects of a folksonomic system are somewhat heterogeneous(i.e., users, resources, and tags). Therefore, uniform application of the voting notion of PageRank and HITS based on the links to a folksonomy would be unreasonable, In a folksonomic system, each link corresponding to a property can have an opposite direction, depending on whether the property is an active or a passive voice. The current research stems from the Idea that a graph-based ranking algorithm could be applied to the folksonomic system using the concept of mutual Interactions between entitles, rather than the voting notion of PageRank or HITS. The concept of mutual interactions, proposed for ranking the Semantic Web resources, enables the calculation of importance scores of various resources unaffected by link directions. The weights of a property representing the mutual interaction between classes are assigned depending on the relative significance of the property to the resource importance of each class. This class-oriented approach is based on the fact that, in the Semantic Web, there are many heterogeneous classes; thus, applying a different appraisal standard for each class is more reasonable. This is similar to the evaluation method of humans, where different items are assigned specific weights, which are then summed up to determine the weighted average. We can check for missing properties more easily with this approach than with other predicate-oriented approaches. A user of a tagging system usually assigns more than one tags to the same resource, and there can be more than one tags with the same subjectivity and objectivity. In the case that many users assign similar tags to the same resource, grading the users differently depending on the assignment order becomes necessary. This idea comes from the studies in psychology wherein expertise involves the ability to select the most relevant information for achieving a goal. An expert should be someone who not only has a large collection of documents annotated with a particular tag, but also tends to add documents of high quality to his/her collections. Such documents are identified by the number, as well as the expertise, of users who have the same documents in their collections. In other words, there is a relationship of mutual reinforcement between the expertise of a user and the quality of a document. In addition, there is a need to rank entities related more closely to a certain entity. Considering the property of social media that ensures the popularity of a topic is temporary, recent data should have more weight than old data. We propose a comprehensive folksonomy ranking framework in which all these considerations are dealt with and that can be easily customized to each folksonomy site for ranking purposes. To examine the validity of our ranking algorithm and show the mechanism of adjusting property, time, and expertise weights, we first use a dataset designed for analyzing the effect of each ranking factor independently. We then show the ranking results of a real folksonomy site, with the ranking factors combined. Because the ground truth of a given dataset is not known when it comes to ranking, we inject simulated data whose ranking results can be predicted into the real dataset and compare the ranking results of our algorithm with that of a previous HITS-based algorithm. Our semantic ranking algorithm based on the concept of mutual interaction seems to be preferable to the HITS-based algorithm as a flexible folksonomy ranking framework. Some concrete points of difference are as follows. First, with the time concept applied to the property weights, our algorithm shows superior performance in lowering the scores of older data and raising the scores of newer data. Second, applying the time concept to the expertise weights, as well as to the property weights, our algorithm controls the conflicting influence of expertise weights and enhances overall consistency of time-valued ranking. The expertise weights of the previous study can act as an obstacle to the time-valued ranking because the number of followers increases as time goes on. Third, many new properties and classes can be included in our framework. The previous HITS-based algorithm, based on the voting notion, loses ground in the situation where the domain consists of more than two classes, or where other important properties, such as "sent through twitter" or "registered as a friend," are added to the domain. Forth, there is a big difference in the calculation time and memory use between the two kinds of algorithms. While the matrix multiplication of two matrices, has to be executed twice for the previous HITS-based algorithm, this is unnecessary with our algorithm. In our ranking framework, various folksonomy ranking policies can be expressed with the ranking factors combined and our approach can work, even if the folksonomy site is not implemented with Semantic Web languages. Above all, the time weight proposed in this paper will be applicable to various domains, including social media, where time value is considered important.