• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.7
• /
• pp.604-611
• /
• 2004

It is well known that wall impedance essentially determines how sound wave transmits from one place to another. The wall impedance is related with its dynamic properties : for example, the mass, stiffness, and damping characteristics. It is noteworthy, however, that the wall impedance is also function of spatial characteristics of two spaces that is separated by the wall. This is often referred that the wall is not locally reacting. In this paper, we have attempted to see how the acoustic characteristics of the two spaces is affected by various structure parameters such as density, applied tension, and a normalized length of the wall. Calculations are conducted for two different modally reacting boundary conditions by modal expansion method. The variation of the Helmholtz mode and the structural-dominated mode are analyzed as the structure parameters vary. The displacement distribution of the structure, pressure and active intensity of the inside and outside cavity are presented at the Helmholtz mode and the structure-dominated mode. It is shown that the frequency characteristics are governed by both structure-and fluid-dominated mode. The results exhibit that the density of the structure is the most sensitive design parameter on the frequency characteristics for the coupling system as we could imagine in the beginning. The Helmholtz mode frequency decrease as density increases. However. it increases as applied tension and an opening size increase. The bandwidth of the Helmholtz mode is mainly affected by density of the structure and its opening size.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.1
• /
• pp.21-34
• /
• 1984

This paper is concerned with the experimental investigation of transverse vibration characteristics in water of rectangular plates having an inner free cutout. Systematic experiments are carried out to investigate effects of the surrounding water on the added mass and the natural frequency of the plates due to the changes of the aspect ratio, hole size and eccentricity. The main subject is the clamped rectangular plate with a circular hole. For the purpose of comparative evaluations, some other common-type boundary conditions and hole shapes such as ellipses and rectangles are also investigated. Some of the results obtain are as follows; 1) For each given aspect ratio of the plate, there is a hole area ratio which gives a minimum value of the nondimensional frequency parameter for each mode. The hole area ratio increases as the order number of the mode increases. 2) The nondimensinal mass-increment parameter decreases as the aspect ration or the order number of the mode increases. For each given aspect ratio, the parameter the fundamental mode decreases monotonically as the hole area ratio increase. In cases of the second and higher order modes, however, each mode has a hole area ratio which gives a maximum value of the parameter for each aspect ratio more then 2/3. 3) Comparing elliptic holes with rectangular ones with same hole area ratio, nondimensional frequency parameters are almost same for each given ratio of the shorter axises to the longer one. 4) The influences of difference in boundary condion on nondimensional frequency parameters in water are similar to those in air.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.268-272
• /
• 2006

We have demonstrated the selection and the amplification of the components of an optical frequency comb using femto-second laser injection-locking technique. We used a mode-locked Ti:sapphire laser as a master laser and a single-mode diode laser as a slave laser. After passing through the interference filter with the center wavelength 794.7 nm and the transmittance bandwidth 1.5 nm, the optical frequency comb by mode-locked femto-second laser was injected into the slave laser. The injection-locked slave laser had $3{\sim}4$ multi-mode with the mode spacing 100.5 MHz, whichcorrespond to the repetition rate of a mode-locked Ti:sapphire laser. The power of the modes selected by femto-second laser injection-locking technique was amplified to several thousands times

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.246-256
• /
• 2007

In this paper, a novel type auxiliary active edge resonant snubber assisted zero current soft switching pulse modulation Single-Ended Push Pull (SEPP) series load resonant inverter using IGBT power modules is proposed for cost effective consumer high-frequency induction heating (IH) appliances. Its operating principle in steady state is described by using each switching mode's equivalent operating circuits. The new multi resonant high-frequency inverter with series load resonance and edge resonance can regulate its high frequency output power under a condition of a constant frequency zero current soft switching (ZCS) commutation principle on the basis of the asymmetrical pulse width modulation (PWM) control scheme. Brand-new consumer IH products using the proposed ZCS-PWM series load resonant SEPP high-frequency inverter using IGBTs is evaluated and discussed as compared with conventional high-frequency inverters on the basis of experimental results. In order to extend ZCS operation ranges under a low power setting PWM as well as to improve efficiency, the high frequency pulse density modulation (PDM) strategy is demonstrated for high frequency multi-resonant inverters. Its practical effectiveness is substantially proved from an application point of view.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.52-62
• /
• 1996

In this paper, a new continuous-time current-mode integrator as basic building block of the low-voltage analog current-mode active filters was proposed. Compared to the current-mode integrator which was proposed by Zele, the proposed current-mode integrator had higher unity gain frequency and output impedance in addition to lower power dissipation. And also, a current-mode third-order lowpass active filter was designed with the proposed current-mode integrator. The designed circuits were fabricated using the ORBIT's 1.2.mu.m double-poly double-metal CMOS n-well process. The experimental resutls of the active filter designed and fabricated for this research have shown that it has the performance of 44.5MHz cutoff frequency, 3.3mW power dissipation and the third-order active filter area was 0.12mm$^{2}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.9A
• /
• pp.874-881
• /
• 2008

This paper presents an automatic frequency control algorithm for RTLS DS-SS modem based on the standard of ISO/IEC 24730-2. The presented automatic frequency control algorithm consists of frequency acquisition mode and frequency tracking mode, and the frequency acquisition mode is divided into the angle estimation step for frequency offset estimation and the verification step for removing the angle ambiguity. In the angle estimation step, three different sub-bit angles are estimated according to the timing intervals, then the estimates are used to re move the angle ambiguity in the verification step. The theoretical analysis and the simulation results of the proposed frequency control algorithm are presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.8-14
• /
• 2014

This paper presents the intra capacitance modeling according to the winding method and section bobbin for CM choke capable of the EMI attenuation of broad bands from lower frequency bands to higher frequency bands and high frequency type common-mode choke capable of the EMI attenuation of high frequency band used in the EMI Block of LED-TV SMPS. In case of high frequency type CM choke, it can be explained the parasitic capacitance of A type and section bobbin type winding methods among them is much smaller than the other. The first resonant frequency of the proposed CM choke tends to increase as the parasitic capacitance becomes small and its impedance characteristics also show improved performance as the first resonant frequency increases. In the future, the CM chokes of high frequency type show it can be practically used in not only LED/LCD-TV SMPS but also several applications such as LED Lighting, Adapter and so on.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.6
• /
• pp.820-827
• /
• 2014

Since a microgrid has renewable energy sources, imbalance between power supply and power demand occurs in the islanded mode. In order to solve the imbalance, several energy storage systems (ESSs) such as bettary energy storage system (BESS), EDLC (electric double layer capacitor), flywheel, and SMES (superconducting magnetic energy storage) are generally used. Especially, their electrical characteristics are different. For efficient use of them, a coordinated control scheme is required. In this paper, a coordinated control scheme for using a Lead-acid BESS, a Lithium BESS, and a EDLC is designed to efficient frequency control for a microgrid in the islanded mode. The coordinated frequency control strategy is designed based on their electrical characteristics. The feasibility of the proposed coordinated frequency control strategy is verified through the simulation.

• Current Research on Agriculture and Life Sciences
• /
• v.4
• /
• pp.95-101
• /
• 1986

A computer-controlled automatic vibratory tillage test equipment which attained minimum draft and power was developed. Three control program modes were developed and tested with this equipment. A computer simulation investigated the control performances of the above modes with the following primary results. 1) All of the three control modes converged to the same steady state when the velocity ratio was kept constant. 2) The control mode in which the blade frequency was twice of the soil shearing frequency (frequency control mode) showed optimum control with minimum draft and power, and also had greatest velocity convergence. 3) Results of the simulations showed the frequency control mode to have achieved the best control performance. The fluctuation of the draft reduction was less than 10% at various cutting depths and soil moistures.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.2
• /
• pp.313-323
• /
• 2013

Offshore floating structures have so-called moonpool in the centre area for the purpose of drilling, installation of subsea structures, recovery of Remotely-Operated Vehicle (ROV) and divers. However, this vertical opening has an effect on the operating performance of floating offshore structure in the vicinity of moonpool resonance frequency; piston mode and sloshing mode. Experimental study based on model test was carried out. Moonpool resonance of floating offshore structure on fixed condition and motion free condition were investigated. And, the effect of cofferdam which is representative inner structure inside moonpool was examined. Model test results showed that Molin's theoretical formula can predict moonpool resonance on fixed condition quite accurately. However, motion free condition has higher resonance frequency when it is compared with that of motion fixed. The installation of cofferdam moves resonance frequency to higher region and also generates secondary resonance at lower frequency. Furthermore, it was found that cofferdam was the cause of generating waves in the longitudinal direction when the vessel was in beam sea.