• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.720-725
• /
• 2010

In AGPS method, user position can be obtained even in the shadow region by improving signal sensitivity. A hybrid long integration scheme employing both coherent and non-coherent integration method is commonly used in AGPS receivers. Because coherent loss increases as residual frequency become large, residual frequency should be minimized to maximize coherent integration gain. This paper presents performance analysis of residual frequency estimator using FFT in fine-time assistance AGPS method. Considering the hardware complexity and the estimation accuracy, optimal length of FFT is proposed for GPS L1 C/A signal. Signal sensitivity for estimating the residual frequency is also analysed. By field experimental results, it is found that the residual frequency can be successfully estimated using 1 second snap-shot data when GPS signal strength is larger than -150 dBm and its RMS error is 3Hz.

• 전력전자학회논문지
• /
• 제27권3호
• /
• pp.256-264
• /
• 2022

The frequency power control method (FCM) which has a wide operating frequency range is adopted for induction heating (IH) cooktops. When FCM is applied to the full-bridge series resonant converter (FB-SRC) based IH system, high-frequency switching of the inverter is required compared to the half-bridge SRC (HB-SRC)-based IH system. Therefore, the switching loss of the inverter increases, and applying FCM under the condition that the inverter operating frequency range is limited is difficult. Therefore, this paper proposes a control strategy with the phase shift power control method considering that limited frequency conditions are presented. Loss analysis following the control method is performed through simulation and mathematical analysis. In addition, the validity of the proposed control strategy is verified by analyzing the heating performance following the control method through the test results of the 3,200[W] prototype.

• 대한기계학회논문집A
• /
• 제30권9호
• /
• pp.1154-1159
• /
• 2006

In this paper, time-frequency analysis and multi-dimensional spectral analysis methods are applied to source identification and diagnostic of non-stationary sound vibration signals. By checking the coherences for concerned time, this simulation is very well coincident to expected results. The proposed method analyzes the signal instantaneously in both time and frequency domains. The MDSA (Multiple Dimensional Spectral Analysis) analyzes the signal in the plane of instantaneous time and instantaneous frequency at the same time. And it was verified by using the 1500cc passenger car which is accelerated from 70Hz to 95Hz in 4 seconds, the proposed method is effective in determining the vehicle diagnostic problems.

• Structural Engineering and Mechanics
• /
• 제17권6호
• /
• pp.819-828
• /
• 2004

A new process for estimating the natural frequency and the corresponding damping ratio in large structures is discussed. In a practical situation, it is very difficult to analyze large structures precisely because they are too complex to model using the finite element method and too heavy to excite using the exciting force method; in particular, the measured signals are seriously influenced by ambient noise. In order to identify the structural impulse response associated with the information of natural frequency and the corresponding damping ratio in large structures, the analysis process, a so-called "multiresolution blind system identification algorithm" which combines Mallat algorithm and the bicepstrum method. High time-frequency concentration is attained and the phase information is kept. The experimental result has demonstrated that the new analysis process exploiting the natural frequency and the corresponding damping ratio of structural response are useful tools in structural analysis application.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.110-114
• /
• 2012

We studied on the nondestructive evaluation of the elastic wave signal of SiC ceramics and SiC/SiC composite ceramics under monotonic tensile loading. The elastic wave signal of cross and unidirectional SiC/SiC composite ceramics were obtained by pencil lead method and bending test. It was applied for the time-frequency method which used by the discrete wavelet analysis algorithm. The time-frequency analysis provides time variation of each frequency component involved in a waveform, which makes it possible to evaluate the contribution of SiC fiber frequency. The results were compared with the characteristic of frequency group from SiC slurry and fiber. Based on the results, if it is possible to shift up and design as a higher frequency group, we will can make the superior material better than those of exiting SiC/SiC composites.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2009년도 정기 학술대회
• /
• pp.135-138
• /
• 2009

Most of the studies use model order reduction for low frequency (LF) response analysis due to their high computational efficiency. In LF response analysis, one of model order reduction, algebraic substructuring (AS) retains all LF modes when using the modal superposition. However, in mid-frequency (MF) response analysis, the LF modes make very little contribution and also increase the number of retained modes, which leads to loss of computational efficiency. Therefore, MF response analysis should consider low truncated modes to improve the computational efficiency. The current work is focused on improving the computational efficiency using a AS and a frequency sweep algorithm. Finite element simulation for a MEMS resonator array showed that the performance of the presented method is superior to a conventional method.

• 한국습지학회지
• /
• 제20권2호
• /
• pp.105-115
• /
• 2018

수문기상자료의 빈도해석은 풍수해에 따른 대응 및 시설물의 설계기준에 있어 중요한 요소 중 하나이다. 일반적으로 수문기상자료에 대한 빈도해석의 경우 관측자료는 통계적으로 정상성을 가진다고 가정하고, 확률분포의 매개변수를 고려하는 매개변수적 방법을 적용하고 있다. 이러한, 매개변수적 빈도해석을 위해서는 신뢰성 있는 충분한 자료의 수집이 필요하지만, 강수량과 다르게 적설량의 경우 계절적 특성과 함께 최근에는 기후변화로 인한 적설량 관측일수 및 평균 최심신적설량이 감소하기 때문에 부족한 자료에 대한 문제점을 보완할 필요가 있다. 이에 본 연구에서는 매개변수 빈도해석 방법과 부족한 자료의 문제점을 보완할 수 있는 표본 재추출 기법인 Bootstrap방법과 SIR(Sampling Importance Resampling)알고리즘을 적용하여 적설량의 빈도해석을 실시하였다. 58개 기상관측소에 대해 재추출된 일 최대 최심신적설량 자료를 이용한 비매개변수적 빈도해석을 통해 확률적설량을 산정하고 이를 비교 분석하였다. 빈도별 확률적설량의 증감률을 검토한 결과 매개변수적 빈도해석과 비매개변수적 빈도해석에서 증감률을 나타내는 지점들이 대부분 일치하는 것으로 나타났다. 확률적설량은 관측 자료와 Bootstrap방법에서 -19.2%~3.9%, Bootstrap방법과 SIR알고리즘에서 -7.7%~137.8% 정도의 차이를 보였다. 표본 재추출 기법은 관측표본이 적은 적설량의 빈도해석 및 불확실성 범위의 제시가 가능함을 확인할 수 있었고, 이는 여름철 태풍과 같이 계절적 특성을 지닌 다른 자연재난의 해석에도 적용될 수 있을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.85-89
• /
• 2005

For the analysis of a vibrating two dimensional structure such as the simply supported rectangular plate, Spectral Finite Element Method (SFEM) has been studied. Under the condition that two parallel edges are simply supported at least and the other two edges can be arbitrary, Spectral Finite Element has been developed. Using this element SFEM is applied to the vibrating rectangular plate which all edges are simply supported, and obtain the frequency response function in frequency domain and the dynamic response in time domain. To evaluate these results normal mode method and finite element method (FEM) are also accomplished and compared. It is seen that SFEM is more powerful analysis tool than FEM in high frequency range.

• 대한토목학회논문집
• /
• 제33권4호
• /
• pp.1361-1375
• /
• 2013

Lee et al. (2011)이 제시한 목감천 유역의 하천복원 설계절차에 근거하여 수리구조물의 설계와 관련 있는 설계홍수량을 산정에 있어 비정상성을 고려하여 산정하였다. 본 연구의 목적은 목감천 유역에서 비정상성을 고려한 새로운 설계홍수량을 제안하기 위함이다. 설계홍수량 산정방법인 설계-호우단위도법과 직접 홍수빈도해석법을 적용하였으며, 각각의 방법에 사용되는 빈도분석은 NCAR (National Center for Atmospheric Research)에서 개발된 extRemes 모형을 통하여 비정상성을 고려하였다. 직접 홍수빈도해석의 방법은 유량으로부터 직접 빈도해석을 수행한다는 점에서 신뢰성이 기대되지만, 설계-호우단위도법보다 다소 과소 추정되었다. 따라서 가장 크게 산정된 설계호우-단위도법의 100년 빈도 설계홍수량을 목감천 유역의 설계홍수량으로 결정하였다.

• 한국해양공학회지
• /
• 제17권3호
• /
• pp.46-51
• /
• 2003

Acoustic emission (AE) signals, emanated during local failure of aluminum alloys, have been the subject of numerous investigations. It is well known that the characteristics of AE are strongly influenced by the previous thermal and mechanical treatment of the sample. Possible sources of AE during deformation have been suggested as the avalanche motion of dislocations, fracture of brittle particles, and debonding of these particles from the alloy matrix. The goal of the present study is to determine if AE occurring as the result of fatigue crack propagation could be evaluated by the joint time-frequency analysis method, short time Fourier transform (STFT), and Wigner-Ville distribution (WVD). The time-frequency analysis methods can be used to analyze non-stationary AE more effectively than conventional techniques. STFT is more effective than WVD in analyzing AE signals. Noise and frequency characteristics of crack openings and closures could be separated using STFT. The influence of various fatigue parameters on the frequency characteristics of AE signals was investigated.