• 항공우주시스템공학회지
• /
• 제15권1호
• /
• pp.86-94
• /
• 2021

PCB 기반 전개형 태양전지판은 경량화 및 전기적 연결의 용이성으로 주로 큐브위성에 사용되나, 태양전지판의 면적이 증가할수록 발사환경에서 유발되는 굽힘거동이 증가하기 때문에 태양전지셀의 구조건전성 보장에 한계가 있다. 종래에는 태양전지판의 강성증가를 통해 굽힘거동을 최소화하고자 알루미늄 및 복합재 기반의 보강재를 또는 태양전지판을 적용하였지만, 태양전지판의 부피 및 무게 증가로 제한적인 설계요구조건을 가진 태양전지판의 단점으로 작용한다. 본 연구에서는 점탄성 테이프로 다층 박판을 적층하여 고댐핑 특성 구현이 가능한 6U 규격의 고댐핑 적층형 태양전지판을 제안하였다. 제안된 태양전지판의 기본특성파악을 위해 자유감쇠시험을 수행하였으며, 인증수준의 발사진동시험을 통해 설계유효성을 입증하였다. 또한, 시험결과를 토대로 일반 PCB 태양전지판과 고댐핑 적층형 태양전지판의 진동특성을 예측하고 비교분석을 수행하였다.

• Advances in concrete construction
• /
• 제8권1호
• /
• pp.9-19
• /
• 2019

This paper describes an experimental investigation on hybrid fiber reinforced concrete (HYFRC) beams. And the main aim of this present paper is to examine the dynamic characteristics and damage evaluation of undamaged and damaged HYFRC beams under free-free constraints. In this experimental work, totally four RC beams were cast and analyzed in order to evaluate the dynamic behavior as well as static load behavior of HYFRCs. Hybrid fiber reinforced concrete beams have been cast by incorporating two different fibers such as steel and polypropylene (PP). Damage of HYFRC beams was obtained by cracking of concrete for one of the beams in each set under four-point bending tests with different percentage variation of damage levels as 50%, 70% and 90% of maximum ultimate load. And the main dynamic characteristics such as damping, fundamental natural frequencies, mode shapes and frequency response function at each and every damage level has been assessed by means of non-destructive technique (NDT) with hammer excitation. The fundamental natural frequency and damping values obtained through dynamic tests for HYFRC beams were compared with control (reference) RC beam at each level of damage which has been acquired through static tests. The static experimental test results emphasize that the HYFRC beam has attained higher ultimate load as compared with control reinforced concrete beam.

• 마이크로전자및패키징학회지
• /
• 제13권1호통권38호
• /
• pp.63-72
• /
• 2006

최근에 모바일 기기의 사용이 늘어남에 따라 굽힘 응력에 대한 패키지 접합부의 신뢰성에 대한 관심이 다시 높아지고 있다. 기존의 굽힘실험은 생산공정 및 운반 등에 파손을 방지하기 위해서 수행되었으나 최근에는 모바일 기기의 이동 및 사용에 따라 발생되는 응력에 대한 저항성 평가나 드롭시험의 대용으로 수행되고 있다. 본 연구에서는 정확한 4점 굽힘 실험 방법을 도입하여 유연 솔더 조인트와 무연 솔더 조인트의 굽힘 피로 시험에 대한 저항성을 평가하고, 단면 관찰과 유한요소법을 이용한 해석을 수행하였다. 높은 하중이 작용하게 되면, 유연 솔더 조인트가 보다 긴 피로수명을 갖으며, 낮은 하중이 작용할 때는 무연 솔더 조인트가 긴 수명을 가지게 된다. 크랙은 시편의 외각에서 발생되어 안쪽으로 진행하게 되며, 소성변형이 손상의 대부분을 자치하게 된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.427-432
• /
• 1998

The objective of this research is to observe the actual response of low-rise nonseismic moment-resisting reinforced frame subjected to varied levels of earthquake ground motions. First of all, the reduction scale for the model was determined as 1 : 5 considering the capacity of the shaking table to be used. This model was, then, subjected to the shaking table motions simulating Taft N21E component earthquake ground motions, whose peak ground accelerations(PGA's) were modified to 0.12g, 0.2g, 0.3g, and 0.4g. The global behavior and failure mode were observed. The lateral accelerations and displacements at each story and local deformations at the critical portions of structure were measured. The base shear was measured by using specially made load cells. Before and after each earthquake simulation test, free vibration tests were performed to find the changes in the natural period and damping ratio of the model.

• 한국군사과학기술학회지
• /
• 제5권4호
• /
• pp.81-87
• /
• 2002

In this paper, the transonic aeroelastic behavior of the generic fighter model is investigated in the time domain. The simulation of flutter flight test using forced harmonic motion of control surfaces including inertial coupling effects is conducted at the various conditions. The nonlinear aerodynamic effects are considered using a transonic small disturbance equation. A modal model obtained by a free vibration analysis is used for the structural model. The relations between the computed flutter boundary and the simulation results of the responses using the harmonic motions of control surfaces at various conditions are investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1491-1494
• /
• 2003

A specific experimental method, the Split Hopkinson Pressure Bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s∼104/s. This type of test procedure has been used to examine the dynamic response of materials in various modes of testing. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• Nuclear Engineering and Technology
• /
• 제30권5호
• /
• pp.416-423
• /
• 1998

Many studies for the perforated plates have been done, especially on the subject of static behavior and stress distribution in the plate. Equivalent elastic properties are one of the successive concepts for this problem. However little effort was taken to get their dynamic characteristics. In this paper finite element modal analysis was performed for the perforated plates having square and triangular hole patterns. An attempt to use existing equivalent elastic properties into the modal analysis of the plate was carried out. To verify feasibility of the finite element models, modal test was also performed on one typical perforated plate. System parameters such as natural frequencies and mode shapes were extracted and compared with the analysis results.

• 한국안전학회지
• /
• 제24권6호
• /
• pp.150-156
• /
• 2009

The oil pressure switch(OPS) for automobile is very important part to prevent an overheated engine and other problems by checking the operation of an engine oil system and displaying oil signs on a dashboard. OPS is the part that receives various stress caused by temperature, vibration, and corrosion in an engine room. Regarding existing steel OPS cases, there occur field errors due to the rust, and much concern comes from the low anticorrosion caused by CR6+ Free according to the restrictions of heavy metals. Therefore, the study analyzed average life, the failure rate, and reliability through the tests of performance according to temperature changes, mechanical strength, and run-test in order to confirm if the use of the oil pressure switch with Al of anti-corrosion can improves the reliability, instead of the existing steel products.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2186-2188
• /
• 2000

A fiberoptic sensor using an SLD as a light source has been studied. The sensor system employs an intrinsic fiber Fabry-Perot interferometer as a sensing tip and a fiber Mach-Zehnder interferometer as a processing one. A free loading test for temperature application shows that the fiberoptic sensor has a wide-dynamic range as well as high resolution. Due to the inherent property of the optical fiber itself and the intrinsic Fabry-Perot interferometer. the fiberoptic sensor gives obvious benefits when it is applied to harsh environments to monitor some physical parameters such as temperature, strain, pressure and vibration.

• Advances in concrete construction
• /
• 제15권4호
• /
• pp.269-286
• /
• 2023

In the present study, we aim to utilize the numerical solution frequency results of functionally graded beam under thermal and dynamic loadings to train and test an artificial neural network. In this regard, shear deformable functionally-graded beam structure is considered for obtaining the natural frequency in different conditions of boundary and material grading indices. In this regard, both analytical and numerical solutions based on Navier's approach and differential quadrature method are presented to obtain effects of different parameters on the natural frequency of the structure. Further, the numerical results are utilized to train an artificial neural network (ANN) using AdaGrad optimization algorithm. Finally, the results of the ANN and other solution procedure are presented and comprehensive parametric study is presented to observe effects of geometrical, material and boundary conditions of the free oscillation frequency of the functionally graded beam structure.