• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.48-58
• /
• 1995

In this study, a contact algorithm for the finite element analysis of free surface contact problem in materials forming is presented. The proposed contact algorithm consists of two parts. The first is the contact searching part, and the second, the constraint part. The contact searching algorithm does not require any a priori knowledge of the pairs of contact nodes or segments and the impenetrability constraint is satisfied using the penalty function scheme. void colsure in open-die forging was simulated to verify the accuracy and capability of the currently developed contact algorithm. The simulation results, obtained from ABAQUS simulation, were compared well to the experimental data available in the literature.

• Journal of Welding and Joining
• /
• v.22 no.4
• /
• pp.43-49
• /
• 2004

Conventional method for electrode force application in resistance spot welding(RSW) processes is to use pneumatic cylinder. However, due to its inherent problems in pneumatic power system such as compressibility of air and poor transient response characteristics, new electrode force system with servo control are recently introduced in RSW machine. This machine is called “servogun”. The purpose of this study is to evaluate performance of servogun in case of spot welding of aluminum alloy. Aluminum alloy(A5052) sheets are spot welded using pneumatic gun and servogun. Both results are compared by means of macro cross-section etching test and tensile shear strength test. Numerous previous research have reported nugget with many voids and cracks are not uncommon defects in spot welds with aluminum alloy. The experimental results show similar defects in case of pneumatic gun. In contrast, use of servogun considerably reduced generation of voids and cracks. In case of step-wise increased forging force at the end of welding cycle with servogun, crack-free and void-free nuggets have been observed. The performance of servogun has been also verified by series of tensile shear test. Higher strength values have been achieved with servogun in comparison to that of pneumatic gun.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.90-93
• /
• 2003

Forging machinery traditionally gives an impression of heavy, greasy, noisy and approximate equipment. Recent demands from markets, especially automobile, have made machine designers to reconsider their concept. It is also noted that more advanced technologies in other industries, such as electronics and IT, have become accessible. Naturally these technologies were first applied in highly sophisticated fields for additional performance or features with extra expense. Drastic cost reduction in last decade changes this picture. They provide not only performance and functions but also a chance in reducing costs. Powerful servomotors, accurate sensors and fast processor satisfy performance, precision and machine control requirement. Control by wires replaces traditional mechanical linkage. Additional features such as factory automation will come almost free.

• Transactions of Materials Processing
• /
• v.12 no.4
• /
• pp.340-347
• /
• 2003

In the rigid-plastic finite element simulation of hot forging processes using hexahedral mesh, remeshing of a flash is important for design and control of the process to obtain desirable defect-free products. The mesh compression method is a remeshing technique which enables the construction of an effective hexahedral mesh in the flash. However, because the mesh is distorted during the compression procedure of the mesh compression method, when it is used in resuming the analysis, it causes discretization error and decreases the conversance rate. Therefore, mesh smoothing is necessary to improve the mesh quality. In this study, several geometric mesh smoothing techniques and optimization techniques are introduced and modified to improve mesh quality. Then, the most adaptive technique is recommended for the mesh compression method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.70-73
• /
• 2007

The forming characteristics of cup-rod combined extrusion process were investigated with process parameter change. Simultaneous forward rod extrusion and backward cup extrusion was conducted with magnesium alloy, AZ31B. Process parameters such as forward extrusion ratio, backward extrusion ratio, and working temperature were controlled in a specific region and the effects of the parameter change were examined. Surface crack was developed in a certain state of the process parameters combination. The crack-free forming limit of the alloy in the combined process was disclosed by the parameter study. The microstructures of the initial and extruded workpieces were observed.

• Journal of the Korean Society of Safety
• /
• v.24 no.6
• /
• pp.150-156
• /
• 2009

The oil pressure switch(OPS) for automobile is very important part to prevent an overheated engine and other problems by checking the operation of an engine oil system and displaying oil signs on a dashboard. OPS is the part that receives various stress caused by temperature, vibration, and corrosion in an engine room. Regarding existing steel OPS cases, there occur field errors due to the rust, and much concern comes from the low anticorrosion caused by CR6+ Free according to the restrictions of heavy metals. Therefore, the study analyzed average life, the failure rate, and reliability through the tests of performance according to temperature changes, mechanical strength, and run-test in order to confirm if the use of the oil pressure switch with Al of anti-corrosion can improves the reliability, instead of the existing steel products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.77-77
• /
• 2009

$Pb(Zr,Ti_O_3$계 세라믹스는 우수한 압전 특성으로 인하여 압전변압기 및 액츄에이터, 센서 등 많은 분야에 응용이 되어져 왔다. 그러나, 최근 들어 $1000^{\circ}C$에서 급속도로 많은 휘발을 하는 PbO는 환경 및 인체에 나쁜 영향을 미칠 뿐 아니라 사용 후의 처리도 어려워 선진국에서는 사용을 제한하거나 줄이고 있는 추세에 있다. 따라서, PbO를 포함하지 않은 무연 (Lead-free)계 압전 세라믹스에 대한 연구가 많은 관심을 끌고 있으며 앞으로는E 장래성 있는 하나의 이슈 분야가 될 것이다. 이러한 Pb-based System 세라믹스를 대체 할 재료로서 $(Bi_{1/2}Na_{1/2})TiO_3$나 Tungsten-Bronze type, $(K_{1/2}Na_{1/2})NbO_3$ 등이 주로 연구가 되고 있다. 특히, alkali niobate를 기초로 한 $(K_{1/2}Na_{1/2})NbO_3(NKN)$은 무연 압전 물질로서 많은 주목을 받고 있다. 그러나, NKN의 주요 성분인 K 의 높은 조해성 때문에 일반적인 고상방법으로는 고 밀도의 세라믹을 얻기 힘들뿐더러 낮은 상전이 온도 때문에 많은 응용에는 제약이 되고 있다. 이러한 세라믹의 단점을 보완하고자 Hot forging, RTGG, SPS 등 과 같이 특수한 소결방법을 사용하여 고밀도의 세라믹을 제작하지만 이 방법들은 제품 대량 생산에 있어 경제적으로나 복잡한 제조과정을 고려할 때 매우 비효율적이라고 판단된다. 그러므로 $BaTiO_3$, $LiTaO_3$, Mg, Ca등을 첨가 시켜 소결을 향상시키고 고밀도를 얻기 위해 많은 연구가 진행 중이다. 따라서 본 연구에서는 Pb-based계의 세라믹스를 대체할 우수한 특성의 세라믹스를 제작하고자 기존의 $(K_{1/2}Na_{1/2})NbO_3(NKN)$세라믹스에서 낮은 용융온도 때문에 소결하기 어려운 $KNbO_3$를 제거한 $NaNbO_3$에 $LiNbO_3$와 $BaTiO_3$를 추가한 $NaLiNbO_3-BaTiO_3$세라믹스에 $K_4CuNb_8O_{23}$(KCN)을 첨가함으로서 이에 따른 압전 및 유전 특성을 조사하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.99-101
• /
• 2008

At 21st century, material development concepts were changed to fulfill the environmental friendly demands. This study is to study the effect of pressurized nitrogen gas and manganese in high nitrogen austenitic stainless steel(HNS) in which N and Mn elements substitute the nickel element. 100kg HNS ingots were made by Pressurized Vacuum Induction Melting(P-VIM) and were forged according to free forging process. As forged HNS were hot and cold rolled by pilot scale rolling machine. Depending on the rolling condition, the mechanical properties of HNS were changed. The roll thrust and sheet folding showed asymmetry condition between work and drive side during cold and hot rolling. The purpose of this study are to improve workability the hot and cold rolling machine and to set the conditions for establishing the rolling process.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.5
• /
• pp.230-237
• /
• 2010

FTMP(friction thermo-mechanical process) is an adaptation of friction stir welding, and can be used as a generic process to modify the microstructure at selective locations. In this study, in order to analyze characteristics of surface modification of ACA4 castings by FTMP, change of rotating speed(R/S) and traveling speed(T/S) of tool were applied as conditional parameter. Analysis of microstructure, hardness, surface roughness and depth of modified zone(MZ) were searched. The best condition were obtained at R/S 600 rpm and T/S 100 mm/min. At this time, hardness was 82 HV, the surface roughness was 0.07 mm and the depth at MZ was 1.72 mm. Free defects microstructure and fine Si particles formation and strong forging effects were analyzed at MZ.

• Transactions of Materials Processing
• /
• v.18 no.1
• /
• pp.26-38
• /
• 2009

It was reported that the semi-solid forming process has many advantages over the conventional forming process, such as a long die life, good mechanical properties and energy savings. It is very important, however, to control liquid segregation to gain mechanical property improvement of materials. During forming process, rheology material has complex characteristics, thixotropic behavior. Also, difference of velocity between solid and liquid in the semi-solid state material makes a liquid segregation and specific stress variation. Therefore, it is difficult for a numerical simulation of the rheology process to be performed. General plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. The behavior and stress of solid particle in the rheology material during forging process is affected by viscosity, temperature and solid fraction. In this study, compression experiments of aluminum alloy were performed under each other tool shape which is rectangle shape(square array), rectangle shape(hexagonal array), and free shape tool. In addition, the dynamics behavior compare with Okano equation to power law model which is viscosity equation.