• 한국세라믹학회지
• /
• 제36권12호
• /
• pp.1390-1395
• /
• 1999

Zr(Y,Ce)O2 TZP ceramics were prepared by sintering compacts of 3 mol% Y2O3-TZP(3Y-TZP) powders with different amount of 12 mol% CeO2-TZP(12Ce-TZP) in air at 140$0^{\circ}C$ for 2 h. The phase changes microstructure and mechanical properties of Zr(Y. Ce)O2 TZP after hydrothermal aging(20$0^{\circ}C$ 5h) were investigated. Although an addition of 12Ce-TZP accelerated the grain growth of Zr(Y, Ce)O2 TZP it restrained the transformation of tetragonal to the monoclinic phase during aging. The degradation in mechanical properties of sintered bodies was governed by the formed monoclinic phase and chemical composition. Induced Vickers indentation crack was propagated intergranually. From SEM observation of the fracture surfaces the pull-out of individual grain was confirmed.

• 소성∙가공
• /
• 제25권5호
• /
• pp.306-312
• /
• 2016

Effects of manufacturing conditions, such as austenitizing temperature, patenting temperature and carbon content in steels, on mechanical properties, especially on reduction of area (RA), of hyper-eutectoid steel wires were investigated. RA increased and then decreased with transformation temperature. This was attributed to the presence of abnormal structures in steels transformed at low transformation temperatures and the occurrence of shear cracking during tensile testing of steels transformed at high transformation temperatures. The increase of austenitizing temperature resulted in the increased austenite grain size and consequently the decrease of RA. The decrease of RA with increasing the carbon content in steels was attributed to the increased fraction of cleavage fracture in tensile fractured surfaces.

• 한국주조공학회지
• /
• 제12권5호
• /
• pp.397-402
• /
• 1992

The effect of the solution & aging treatment on the tensile strength, yield strength, elongation, reduction of area, hardness was studied in the 17-4 PH stainless steel. SEM pictures were also taken in order to examine the fracture surfaces and precipitated particles. X-ray diffraction patterns for the heat treated samples were also observed. Mechanical properties of the heat treated samples were superior to those of as cast samples. Tensile strength, yield strength, hardeness decreased with the increase of aging temperature. On the other hand, elongation and reduction of area increased as the aging temperature increased.

• 한국생산제조학회지
• /
• 제21권1호
• /
• pp.85-89
• /
• 2012

Conventional grinding of BK7 glass will normally result in brittle fracture at the surface, generating severe sub-surface damage and poor surface finish. The precision grinding of BK7 glass in parallel grinding modes has been investigated. Grinding process, maximum chip thickness, ductile/brittle regime, surface roughness and sub-surface damage have been addressed. Special attention has been given to the condition for generating a ductile mode response on the ground surface. Experiments reveal that the level of surface roughness and depth of sub-surface damage vary differently for different condition. This study gives an indication of the strategy to follow to achieve high quality ground surfaces on brittle materials.

• 마이크로전자및패키징학회지
• /
• 제6권2호
• /
• pp.1-12
• /
• 1999

Brown oxide and/or black oxide layers were formed on the surface of Cu-based leadframe by chemical oxidation of leadframe in hot alkaline solutions, and their growth characteristics were studied. Then, to measure the adhesion strength between leadframe and epoxy molding compound (EMC), oxidized leadframe samples were molded with EMC and machined to form sandwiched double-cantilever beam (SDCB) specimens and pull-out specimens, respectively. Results showed that the adhesion strength of un-oxidized leadframe/EMC interface was inherently very poor but could be increased drastically with the nucleation of acicular CuO precipitates on the surface of leadframe. The presence of smooth faceted $Cu_2O $ on the surfaces of leadframe gave close to zero interfacial fracture toughness (Gc) and reasonable pull strength (PS). A direct correlation between Gc and PS showed that PS can be a measure of Gc only in a limited range.

• 한국분말재료학회지
• /
• 제15권2호
• /
• pp.142-147
• /
• 2008

The hypereutectic Al-20 wt%Si powders including some amount of Cu, Fe, Mg, Mn were prepared by a gas atomization process. In order to get highly densified Al-Si bulk specimens, the as-atomized and sieved powders were extruded at $500^{\circ}C$, Microstructure and tensile properties of the extruded Al-Si alloys were investigated in this study. Relative density of the extruded samples was over 98%. Ultimate tensile strength (UTS) in stress-strain curves of the extruded powders increased after T6 heat treatments. Elongation of the samples was also increased from 1.4% to 3.2%. The fracture surfaces of the tested pieces showed a fine microstructure and the average grain size was about $1{\mu}m$.

• 한국안전학회지
• /
• 제19권1호
• /
• pp.6-11
• /
• 2004

CNG buses were introduced in 2002 to reduce air pollution to the big cities. The durability and safety evaluation were performed for the NGV-2 type cylinders taken from two buses after 30 months of running. No external damage and no internal corrosion was observed on the container surfaces. Defect exceeding the allowable limit was not found in the UT test. Permanent volume expansion was about 1.2% which is much smaller than the required design limit. Cycling test showed no failure after 11,250cycles and burst pressures were still above the maximum design pressure. Both the longitudinal and circumferential failure mode were observed, where both the fracture strengths were far above the design limit. This study showed the present CNG fuel cylinders were safe enough for further usage.

• Macromolecular Research
• /
• 제9권6호
• /
• pp.297-302
• /
• 2001

Rice starch was incorporated into linear low density polyethylene (LLDPE) using a Brabender Plastic-Corder internal mixer at a temperature of 140$\^{C}$ and 40 rpm. The starch loading was varied from 0 to 30% with 5 intervals. Studies on brabender torque development, mechanical properties and water absorption were investigated. The starch loading did not influence the brabender torque significantly. With respect to mechanical properties; the tensile strength and elongation at break decrease with increasing starch loading. The Young's modulus also increases with the starch filling. Mechanical properties were deteriorated as the starch absorbed moisture. The rate of water absorption was dependent on the starch filling in the composites. The scanning electron microscope (SEM) analysis was performed for the tensile fracture surfaces and it revealed the starch agglomeration and a poor dispersion of starch in the LLDPE matrix.

• 대한치과보철학회지
• /
• 제47권4호
• /
• pp.406-415
• /
• 2009

연구목적: 본 연구는 유색 및 백색 지르코니아 세라믹으로 제작된 코핑의 디자인에 따른 지르코니아 세라믹 코핑의 파절 하중과 변연 적합성을 평가한 것으로 그 결과를 임상에 응용하는데 도움을 주고자 하였다. 연구재료 및 방법: CAD/CAM system (Everset, KAVO Dental GmbH, Biberach, Germany)을 이용하여, 80개의 상악 제1 소구치 세라믹 코핑을 제작하되, 1그룹은 전체적으로 균일하게 0.3 mm로, 2그룹은 협면 0.3 mm 설면 0.6 mm, 3그룹은 전체 0.6 mm 균일하게, 4그룹은 협면 0.6 mm 설면 1.0 mm로 디자인하고, 유색 (I) 및 백색 (II) 지르코니아 코핑을 각 그룹당 10개가 되게 하였다. 소성직후와 조정 후 코핑의 변연 적합성을 Video Microscope System (sv-35, Sometech, Seoul, Korea)를 이용하여 100배율로 관찰하였고, 금속 주 모형에 코핑을 강화형 글래스아이오노머 시멘트로 합착 후 Universal Testing Machine (Instron 4467, Norwood, MA, USA)을 이용하여 파절 하중을 측정하여, one-way ANOVA test 를 시행하여 결과를 분석하였다. 결과: 1. CAD/CAM 지르코니아 코핑의 파절 하중은 1그룹, 2와 3그룹, 그리고 4그룹간에 유의성있는 차이를 보였으며 I4, II4의 파절 하중값이 가장 컸다. 2. 코핑의 디자인이 같고 색이 다른 그룹간의 비교에서는 전 그룹 모두 파절 하중값의 유의성은 없었다. 3. 소성 직후 변연 오차 측정값은 I2그룹을 제외한 전 그룹에서 협측 측정점에서 변연오차가 가장 큰 경향을 보였다. 4. 소성 직후 변연 오차 측정값은 I 그룹 지르코니아 그룹에서 그룹별 전체적인 변연적합도를 보았을 때 그룹간에 유의한 차이는 없었다 (P>.05). 5. 소성직후 변연 오차 측정값은 백색 지르코니아 그룹에서 그룹별 전체적인 변연 적합도를 보았을때 II1그룹의 변연 오차가 가장 컸다 (P<.05). 6. 소성직후 변연오차 측정값은 디자인이 같은 그룹의 유색, 백색 비교에서, I1와 II1그룹을 제외한 나머지 그룹에서 백색 지르코니아의 변연 적합도가 더 좋았다 (P<.05). 7. 내면 조정 후에는 색상화 및 지르코니아 코어 디자인에 따른 전 그룹간 변연 적합도의 차이는 없었다 (P>.05). 결론: 지르코니아 코핑 디자인과 색상화에 따른 변연 적합성은 소성 직후에는 다소 차이가 있었으나 내면 조정을 하면 임상 사용에는 무리가 없을 것으로 판단되었고, 파절강도 강화를 위해 코핑의 두께는 가급적 두꺼워야 하나, 가시면 (순면, 협면)의 심미성(반투명성)을 고려할 경우 가시면을 0.3 mm로 얇게 해도 파절 강도에 큰 영향을 주지 않는 것으로 사료되었다.

• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.97-112
• /
• 1995

The purpose of this study was to evaluate the effect of wetting condition made by drying time on bonding of resin cement to dentin. Freshly extracted bovine teeth were grinded to expose flat dentin surfaces. After the exposed dentin surfaces were treated with pretreatment agents and water rinse, each wetting condition of dentin surfaces was made according to drying times and methods including slight blow bry for I-second by air syringe, blow dry for 20-second by air syringe, and 12-hour dry in desiccator respectively. and then, previously made composite resin specimens were bonded onto each conditioned dentin surface of the specimen using Panavia-21(Kuraray Co.), Bistite(Tokuso Co.), and Choice(use with All bond-2, Bisco Inc.) resin cement according as manufacturer's instruction. Bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, then the tensile bond strength was measured, cohesive failure rate was calculated, and fractured dentin surfaces and acrylic rod sides were examined under scanning electron microscope. The result were as follows ; In the group of bonding with Panavia-21 resin cement, higher tensile bond strength was seen in 12-hour dry group than in I-second and 20-second dry group(p<0.01). In the group of bonding with Bistite resin cement, higher tensile bond strength was seen in 1-second dry group than in 20-second and 12-hour dry group(p<0.01). In the group of bonding with Choice resin cement, no significant differences of bond strength under given drying time were seen. Cohesive failure rates derived from the groups of bonding with Panavia-21 and Choice resin cement were increased with the increase of tensile bond strength in each drying time. On SEM examination of fractured surface, adhesive failure mode with fractured resin tags was mostly seen in wet condition with I-second drying time in the group of bonding with Panavia-21 resin cement, mixed failure mode with shortened and fractured resin tag was seen in the group of bonding with Bistite resin cement, and regardless of drying time, and cohesive-adhesive mixed failure mode with fracture of 'Hollow' typed resin tags was mainly seen in the group of bonding with Choice resin cement.