• Korean Management Science Review
• /
• v.20 no.2
• /
• pp.179-196
• /
• 2003

Function point model is the international standard method to measure the software size which is one of the most important factors to determine the software development cost. Function point model can successfully be applied only when the detailed specification of users' requirements is available. In the domestic public sector, however, the budgeting for software projects is carried out before the requirements of softwares ere specified in detail. Therefore, an efficient function point estimation method is required to apply function point model at the early stage of software development projects. The purpose of this paper is to compare various function point estimation methods and analyse their accuracies in domestic software projects. We consider four methods : NESMA model, ISBSG model, the simplified function point model and the backfiring method. The methods are applied to about one hundred of domestic projects, and their estimation errors are compared. The results can used as a criterion to select an adequate estimation model for function point counts.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.7
• /
• pp.19-25
• /
• 1995

Presently, along with the advance of high-technology, the precise measurement of linear displacement has become a staple requirement, and consequently the high resolution with submicron order has also been required in precise positioning and carriaging. In this paper, we advance a propose on a new type of laser encoder based on the principle of phase analysis of the moire fringes from superimposed two gratings. The phase angle as an information of displacement can be accurately calculated by detecting the change in brighness at four points of the fringes. The actual application of four point method to the moire fringes is performed thru microcomputer for general purpose, and the measuring procedure is also studied in this research. As an experimental result, in the case of using 20 .mu. m-pitch gratings, it is validated that this method has the resolution of 0.01 .mu. m and the accuracy of .+-. 0.15 .mu. m over the setting range of 100mm.

• Journal of Oriental Neuropsychiatry
• /
• v.3 no.2
• /
• pp.97-106
• /
• 1992

The literature which was written about manual technique of 'Four method of conducting the Qi(氣)'suggest the following results. 1. Four method of conducting the Qi(氣) is a total method based on the basic manual method, lifing and thrusting, twisting and rotating(捻轉), timing the insertion and withdrawal(呼吸) ect. 2) Cheongryongphami method(靑龍擺尾法) come to understanding channels and conducting and Qi(氣), Paekhoyodu method(白虎搖頭法) using a channels understanding and Qi(氣) introducing, Changkuthamhyeol method(蒼龜探穴法) using a channels understanding, Ceokpongyeongweon method(赤鳳迎源法) using a collaterals understanding. 3) Cheongryongphami(靑龍擺尾) and Changkuthamhyeol method(蒼龜探穴法) were used on disease like insufficiency symptom-complex(盧證), Paekhoyodu(白虎搖頭) and Ceokpongyeongweon method(赤鳳迎源法) were used on excessivess symptom-complex(實證) of pathogenic factors selectively. But all of them often used on C.V.A. 4) The Yang Channel's points, under the elbow and knee point, are often used as points which are used in "Four method of conducting the Qi(氣), and the Yin, Ren(任) Du(督) channels are used less than the former. 5) The manual techniques of 'Four method of conducting the Qi(氣)' are often used in clinically. "Four method of conducting the Qi(氣)"has been studies as above, but there weren't a lot of literature which is about total manual technique of acupuncture. So there is a need study about it.

• Journal of Sasang Constitution and Immune Medicine
• /
• v.17 no.1
• /
• pp.1-15
• /
• 2005

1. Objectives Scarcely referred except for a few phrases of the acupuncture of Dongmugong. He stated every disease could be cured through acupunture. In addition, generally there are a certain point('hyul-穴') of the body that suits according to the constitutions, and just as there are a theory that 'ascend-descend-loosen-tighten(升降緩束)' so as therapy of the symptom has the same. However, he did not indicate the concrete method of the four constitutional acupuncture. He only asked his descendants to study about it. 2. Methods Therefore, author of the thesis tries to describe the theory approach to the seletive method of four constitutional acupunture point based on ${\ulcorner}$Dongyi Suse Bowon(東醫壽世保元)${\lrcorner}$ 3. Results and Conclusions The author of the thesis recommended the methods to apply twelve channels to sasangin's disease and symptoms according to the ascend(升)-descend(降)-loosen(緩)-tighten(束)

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.267-269
• /
• 2003

반도체 웨이퍼 및 각종 박막의 면/비저항(sheet/resistivity resistance)의 측정에 비교적 간단히 측정할 수 있고 측정정확도가 높은 4탐침(four-point probe)방법이 널리 사용되고 있다 또한 4탐침 측정방법은 높은 분해능의 contour map작성과 ion implantation의 doping accuracy 및 doping uniformity의 측정에도 사용된다. 최근 재료의 소형, 박막화 경향으로 볼 때 정확한 비저항 측정의 필요성이 요구되고 있으며 이에 따라 4탐침 측정기술인 single 및 dual configuration method로 실리콘 웨이퍼에 대한 비저항의 측정 정확도를 고찰한 결과 dual configuration 측정방법이 single configuration측정 방법에 비하여 정밀 정확도가 더 좋은 것으로 고찰되었다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1515-1516
• /
• 2015

Touch panel 및 Touch screen 등의 투명전극으로 많이 사용되고 있는 ITO(Indium Tin Oxide)나 CNT(Carbon Nano Tube) 등 전도성 박막의 면저항을 쉽고 빠르게 측정하기 위하여 van der Pauw method를 이용한 면저항 측정기를 개발하였다. 이 면저항 측정기는 대면적 시료의 면저항을 측정 할 수 있어 매우 편리하다. 면저항 측정은 주로 Four Point Probe method로 측정하는 것이 일반적이나 본 연구에서는 van der Pauw method를 이용한 측정값과 Four Point Probe method로 측정한 결과를 비교한 결과 1 % 이내에서 일치하였다. 개발된 측정기의 측정 정확도는 지시값의 1.0 % 이하이고, 측정범위는 $2{\Omega}/{\square}{\sim} 5k{\Omega}/{\square}$이다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.5A
• /
• pp.389-397
• /
• 2011

In this study, an experiment for the biaxial behavior of specimens was carried out to identify whether the isotropic flexure tensile stress of concrete in the BFT method is feasible. Another experiment for the improvement of the BFT method was conducted to ensure the isotropic flexure tensile stress of BFT specimens during the test. In addition, the biaxial flexure strength of concrete given by the improved BFT method was compared to the uniaxial flexure strength by the four-point bending test. Test results show that the isotropic flexure tensile stress of concrete using the BFT method was highly influenced by the surface conditions and warping of the specimens. Using improved BFT method, we could obtained the isotropic flexure tensile stress of concretes. The biaxial flexure strength of BFT was about 32% greater than the uniaxial flexure strength of the four-point bending test. In the experiment, with the smaller scatter, the improved BFT method gave a reliable biaxial flexure strength like the four-point bending test.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.8
• /
• pp.1231-1239
• /
• 2015

We developed a robot that has four limbs, each of which has the same kinematic structure and has 6 degrees of freedom. The robot is 600mm high and weighs 4.3kg. The robot can perform walking and manipulating task by using the four limbs selectively. The robot has three walking patterns. The first one is biped walking, which uses two rear limbs as legs and two front limbs as arms. The second one is biped walking with supporting arms, which is basically biped walking but uses two arms as supporting legs for increasing stability of the robot. The last one is quadruped walking, which uses all the four limbs as legs. When a task for the robot is given, the robot approaches the task point by selecting an appropriate walking pattern among three walking patterns and performs the task. The robot has many degrees of freedom and is a redundant system for a three dimensional task. We propose a redundancy resolution method, in which the robot’s translational move to the task point is modeled as a prismatic joint and optimal solutions are obtained by optimizing some performance criteria. Several simulations are performed for the validity of the proposed method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.352-359
• /
• 1999

This paper is a research for removing the alternators hunting which came about during the par-allel running. The four-pole six-phase alternator is equipped with the converter made out of twelve diodes to rectify all the waves. The hunting came about during the battery charging due to the hunting inducing point existed in r. p. m band 1575[rpm-1690[rpm] To remove the hunting inducing point We modified the four-pole six-phase alternator into the four-pole twevel-phase and increased the short-circuit ratio by decreasing the field coil pitch and increasing the field coil turns. But this method has two defects the first the alternator structure becomes complicating and the second the second the alternator equipped with the converter used in general purpose lately such as the car alternator can not be run in parallel wlthout modifying. To remove the defects the equalizing line was connected between the same phase of the alterna-tor to flow the synchronizing current which syncronize the phases of generator electromotive forces by which the alternator can be run in parallel without reference to the hunting inducing point and without modifying.

• Korean Management Science Review
• /
• v.14 no.1
• /
• pp.131-149
• /
• 1997

Software cost estimation is an important both for buyers and sellers(developers). We reviewed domestic and foreign researches and practices on software cost estimation with function point method comprehensively, In this paper, we derived four promising alternative function point models. They are an IFPUG(International Function Point User Group)-based model(Model I), a shorthand model for client/sever software systems(Model II), a data-oricnted model for relatively large software projects(Model III), and a general- purpose function point model for non business application softwares as well as business applications(Model IV). Empirical data shows that Model I, II, and IV are very useful function point models. In particular, model II and IV look very useful models since they are concise and accurate. These models can be incorporated in a new improved guideline for software cost estimation. General opinion survey shows that Model I, II and IV are preferable. There are no significant differences in preference between buyers and sellers. The survey also shows that users think function point method is better than step(line of code)-oriented cost estimation methods in many ways including objectivity and estimation accuracy.