• The Journal of Korean Society for Radiation Therapy
• /
• v.15 no.1
• /
• pp.41-52
• /
• 2003

I. Purpose The dose distribution in normal tissues and target lesions is very important in the treatment planning. To make the uniform dose distribution in target lesions, many methods has been used. Especially in the head and neck, the dose inhomogeneity at the skin surface should be corrected. Conventional methods have a limitation in delivering the enough doses to the planning target volume (PTV) with minimized dose to the parotid gland and spinal cord. In this study, we investigated the feasibility and the practical QA methods of the forward IMRT. II. Material and Methods The treatment plan of the forward IMRT with the partial block technique using the dynamic multi-leaf collimator (dMLC) for the patients with the nasopharyngeal cancer was verified using the dose volume histogram (DVH). The films and pinpoint chamber were used for the accurate dose verification. III. Results As a result of verifying the DVH for the 2-D treatment plan with the forward IMRT, the dose to the both parotid gland and spinal cord were reduced. So the forward IMRT could save the normal tissues and optimize the treatment. Forward IMRT can use the 3-D treatment planning system and easily assure the quality, so it is easily accessible comparing with inverse IMRT IV. Conclusion The forward IMRT could make the uniform dose in the PTV while maintaining under the tolerance dose in the normal tissues comparing with the 2-D treatment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.3
• /
• pp.286-286
• /
• 1996

A neural predictive tracking system for the control of structure-unknown dynamic system is presented. The control system comprises a neural network modelling mechanism for the the forward and inverse dynamics of a plant to be controlled, a feedforward controller, feedback controller, and an error prediction mechanism. The feedforward controller, a neural network model of the inverse dynamics, generates feedforward control signal to the plant. The feedback control signal is produced by the error prediction mechanism. The error predictor adopts the neural network models of the forward and inverse dynamics. Simulation results are presented to demonstrate the applicability of the proposed scheme to predictive tracking control problems.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.3
• /
• pp.154-161
• /
• 1996

A neural predictive tracking system for the control of structure-unknown dynamic system is presented. The control system comprises a neural network modelling mechanism for the the forward and inverse dynamics of a plant to be controlled, a feedforward controller, feedback controller, and an error prediction mechanism. The feedforward controller, a neural network model of the inverse dynamics, generates feedforward control signal to the plant. The feedback control signal is produced by the error prediction mechanism. The error predictor adopts the neural network models of the forward and inverse dynamics. Simulation results are presented to demonstrate the applicability of the proposed scheme to predictive tracking control problems.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.1066-1069
• /
• 2002

Dynamic postural control varies with the environmental context, specific task and intentions of the subject. In this paper, dynamic postural control against forward-backward perturbations of a platform was estimated using tri-axial accelerometers and a force plate. Ten young healthy volunteers stood upright in comfortable condition on the perturbation system which was controlled by an AC servo motor. With anterior-posterior perturbations, movements of ankle, knee and hip Joints were obtained by tri-axial accelerometers. and ground reaction forces with corresponding displacements of the center of pressure(CoP) by the force plate. The result showed that the ankle moved first and the trunk forward, which implies that the mechanism of the dynamic postural control in forward-backward perturbations, occurred in the procedure of the ankle, the knee and the hip. Knee flexion and hip extension in the period of acceleration, constant velocity and deceleration phase is very important fur the balance recovery. These responses depends on the magnitude and timing of the perturbation. From the present study the accelerometry-system appears to be a promising tool for understanding kinematic accelerative In response to a transient platform perturbation. A more through understanding of balance recovery mechanism may aid in designing methods for reducing falls and the resulting injuries.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.66-69
• /
• 2008

In this paper, The author present a load current feed-forward compensator by method that improve voltage controller of Step-down Chopper to get stable output voltage to sudden change of load current. To confirm the characteristicsof a presented load current feed -forward compensator compared each transfer function of whole system that load current feed-forward compensator is added with transfer function of whole system that existent voltage controller is included using Mason gains formula in Root locus and Bode diagram. As a result the pole of system is improved, extreme point of the wave and system improves, and size of peak value and phase margin of break frequency in resonance frequency confirmed that is good. Therefore, presented control technique could confirm that reduce influence by perturbation and improves stationary state and dynamic characteristics in output of Step-down Chopper.

• Journal of International Academy of Physical Therapy Research
• /
• v.11 no.1
• /
• pp.1960-1968
• /
• 2020

Background: The alignment of the neck and shoulder is important in people with forward head posture. However, previous studies have mainly conducted fragmentary studies on the neck and shoulders, and studies on the combined movement of the neck and shoulders are incomplete. Objective: To investigate the effects of 6 week dynamic exercise program using Thera-band on craniovertebral angle (CVA) in adults with forward head posture. Design: Quasi-experimental study. Methods: The study was conducted on 24 adults with forward head posture and experimented with neck and shoulder exercises and divided them into groups of neck exercises, shoulder exercises, and neck and shoulder exercises to measure CVA values before and after the experiment. The neck exercise program included flexion and extension muscles of the neck and shoulder exercises included dynamic exercise of the upper extremities such as the trapezius muscles and serratus anterior muscle. The CVA results were measured using PA200. Results: Following the interventions, neck exercise group showed significant improvement in CVA (P<.05), but shoulder exercise group and combined exercise group did not show any significant results (P>.05). However, both groups showed some positive results. Significant differences were seen in the comparisons between the three groups (P<.05), and the results of the post-hoc test showed significant differences in neck exercise group and shoulder exercise, neck exercise and combine exercise group. Conclusion: This study suggested that the Thera-band neck exercise is beneficial for foward head posture patients and is expected to be used in clinical trials.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1972-1977
• /
• 2005

In this work, an inverse dynamic control method is developed to enhance tracking performance of industrial robots, which effectively deal with the nonlinear dynamic interferential forces. In general, the DFF (Dynamic Feed-Forward) controller and the CTM (Computed-Torque Method) controller are used for dynamic control for industrial robots. We study on the practical issues for implementing these inverse dynamic controllers via simulations and experiments. We develop the dynamic models in two different ways. One is a model designed through Newton-Euler method for real time computation and the other is a model designed through SimMechanics for evaluating the developed controller via simulations. We evaluate the nominal performance and robustness of the controller via simulations and experiments using serial 4-DOF HyRoHILS (Hyundai Robot Hardware-In-the-Loop Simulation) system. The results show that the inverse dynamic controller is effective and practically useful for a real control structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.5
• /
• pp.831-835
• /
• 2016

In this paper, a dual-channel feed-forward transimpedance(TIA) array is realized in a standard $0.18-{\mu}m$ CMOS technology which exploits automatic gain control function to provide 40-dB input dynamic range for either detecting targets nearby or sensing imminent danger situations. Compared to the previously reported conventional feed-forward TIA, the proposed automatic-gain-control feed-forward TIA(AFF-TIA) extends the input dynamic range 25 dB wider by employing a 4-level automatic gain control circuit. Measured results demonstrate the linearly varying transimpedance gain of 47 to $72dB{\Omega}$, input dynamic range of 1:100, the bandwidth of $${\geq_-}670MHz$$, the equivalent input referred noise current spectral density of 6.9 pA/${\surd}$HZ, the maximum sensitivity of -26.8 dBm for $10^{-12}BER$, and the power consumption of 27.6 mW from a single 1.8-V supply. The dual-channel chip occupies the area of $1.0{\times}0.73mm^2$ including I/O pads.

• Journal of the Korean Society for Railway
• /
• v.17 no.5
• /
• pp.321-327
• /
• 2014

In this paper, linear dynamic equations are derived from nonlinear dynamic equations of constrained multibody systems using the QR decomposition method. The derived linear equations are applied to a railway vehicle bogie. The vibration characteristics of the railway vehicle are investigated by calculating the natural mode and transfer function of the bogie frame in relation to rail-roughness input. The main modes of the bogie were found below 35Hz, and the local modes above 198Hz. The magnitude of the vertical transfer function varied with the forward velocity due to vertical and pitch modes, which were influenced by the forward velocity. The magnitude of the lateral transfer function was negligibly small, and the mode in the longitudinal direction was excited for longitudinal transfer function regardless of the forward velocity.

• Journal of information and communication convergence engineering
• /
• v.9 no.6
• /
• pp.625-628
• /
• 2011

Dynamic sensor network(DSN) technology which is based on swarming flight type air node offers analyzed and acquired information on target data gathered by air nodes in rotation flight or 3 dimension array flight. Efficient operation of dynamic sensor network based on air node is possible when problems of processing time, data transmission reliability, power consumption and intermittent connectivity are solved. Delay tolerant network (DTN) can be a desirable alternative to solve those problems. DTN using store-and-forward message switching technology is a solution to intermittent network connectivity, long and variable delay time, asymmetric data rates, and high error rates. However, all processes are performed at the bundle layer, so high power consumption, long processing time, and repeated reliability technique occur. DSN based on swarming flight type air node need to adopt store-and-forward message switching technique of DTN, the cancelation scheme of repeated reliability technique, fast processing time with simplified layer composition.