• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.223-230
• /
• 2002

Matched die forming technology has been used widely as a sheet metal forming method for a long time. This conventional method, however, needs a high cost and long delivery time to prepare a set of matched dies or, in many cases, several sets of dies. For more than ten years, some alternative methods using single die or non-matched dies have been developed and applied practically in various fields of industry. Elasto-forming, fluid forming, hydro-forming, and blow forming are some examples of these new methods. Recently, a dieless sheet forming technology using a reconfigurable matrix of punch elements has been developed, and started to be used in some industries such as aircraft and railroads. A new concept of dieless forming technology has also been proposed to overcome the drawback of the conventional dieless forming technology.

• Transactions of Materials Processing
• /
• v.27 no.2
• /
• pp.115-122
• /
• 2018

Most domestic and international standards on the forming limit diagram (FLD) including ISO 12004-2, use a 'position-dependent method,' which determines the forming limit from a strain distribution measured on the specimen after necking or fracture. However, the position-dependent method has inherent problems such as the incidence of asymmetry of a strain distribution, the estimation of missing data near fracture, the termination time of test, and the deformation due to the new stress equilibrium after a fracture, which is blamed for causing sometimes a significant lab-to-lab variation. The 'time-dependent method,' which is anticipated to be a new international standard for evaluating the forming limit, is expected to greatly improve these intrinsic disadvantages of the position-dependent method. It is because the time-dependent method makes it possible to identify and accurately determine the forming limit, just before the necking point from the strain data as continuously measured in a short time interval. In this study, we propose a new time-dependent method based on a Gaussian fitting of strain acceleration with the introduction of 'normalized correlation coefficient.' It has been shown in this study that this method can determine the forming limit very stably and gives a higher value, which is in comparison with the results of the previously studied position-dependent and time-dependent methods.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.45-51
• /
• 2018

Roll forming refers to the production of long plate-molded products, such as panels, pipes, tubes, channels, and frames, by continuously causing the bending deformation to thin plates using rotating rolls. As the roll forming method has advantages in terms of mass production because of its excellent productivity, the size of the roll forming industry has been continuously increasing and the roll forming method is increasingly being used in diverse industrial fields as a very important processing method. Furthermore, as the roll forming method mainly depends on the continuous bending deformation of the plate materials, the time and the cost of the heterogeneous materials developed in the process are relatively large when considered from the viewpoint of plastic working because many processes are continuously implemented. The existing studies on roll forming manufacturing have reported the loss of large amounts of time and materials when the raw materials or product types were changed; further, they have stated that the use of this method can hardly guarantee the uniformity of the formed shapes and the consistency in terms of size and cannot detect all the defects occurring during the mass production and related to the dimensions. Therefore, in this research, a real-time process data-based smart roll forming method that can be applied to multiple products was studied. As a result, a roll forming system was implemented that remembers and automatically sets the changes in the finely adjusted values of the supplied quantities of individual heterogeneous materials so that the equipment setting changing time for heterogeneous material replacements or changes in the products being produced can be shortened. It also secures the uniformity of the products so that more competitive and precise slide-rail products can be mass-produced with improvements in the quality, price, and productivity of the products.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.361-367
• /
• 2015

The forming limit diagram (FLD) is the most commonly used tool for evaluating of sheet metal formability in the manufacturing field as well as the finite element analysis (FEA)-based design process. Determination of the forming limits is considerably influenced by testing/measuring machines, techniques and conditions. These influences may cause a large scatter in FLD from laboratory to laboratory. Scatter is especially true when the ‘position-dependent method’, as is specified in most national and international standards, is used. In the current study a new ‘time-dependent method’ is proposed, which is to determine the forming limit strains more accurately and reasonably when producing a FLD from experimental data. This method is based on continual strain measurement during the test. The results are compared to those from the existing standardized methods.

• Transactions of Materials Processing
• /
• v.31 no.1
• /
• pp.29-38
• /
• 2022

Recently, the composite material market is gradually growing. Various composite forming processes have been developed in order to reduce the production cost of the composite material. Unlike the conventional forming process, the microwave composite forming process has the advantage of reducing the processing time because the composite material is heated directly or indirectly at the same time. Due to this advantage, in this study, a double cantilever beam test was conducted with specimens manufactured by the microwave composite forming process. The purpose of this study was to compare mode-I energy release rate for specimens manufactured by prepreg compression forming and microwave composite forming processes. First, a microwave oven was proposed to conduct the microwave composite forming process. Double cantilever beam specimens were manufactured. After that, the double cantilever beam test was conducted to obtain the mode-I energy release rate. Mode-I energy release rates of specimens manufactured by the microwave composite forming and prepreg compression forming processes were then compared. As a result, mode-I energy release rates of specimens fabricated by the microwave composite forming process were similar to those fabricated with the prepreg compression forming process with a relatively reduced process time.

• Korean Journal of Computational Design and Engineering
• /
• v.11 no.6
• /
• pp.440-446
• /
• 2006

This study relates to the effect of forming time of injection path on the total process. The whole process can be divided into build process of forming path of injection and after treatment process. The total time required for the whole process could be reduced by reducing the forming time of injection path using SLC file to correct the problems of STL file that is the basic file format for high speed molding devices. First of all, I verify the forming time of injection path according to the conditions of STL file during the formation of injection path. And I verify problems using STL file during formation of injection path. And then I tried to solve problems of STL file by comparing between the formation time of injection path and the existing method using SLC files.

• Journal of Power System Engineering
• /
• v.8 no.3
• /
• pp.23-29
• /
• 2004

In this paper, a finite element formulation using dynamic-explicit time integration scheme is used for numerical analysis of Hydro-forming processes. The lumping scheme is employed for the diagonal mass matrix and dynamic explicit formulation. Hydro-forming process for auto-body panel forming is analyzed by using dynamic-explicit finite element method. Further, the simulated results of the Hydro-forming processes are shown and discussed. Its application is being increased especially in the automotive industrial area for the cost reduction, weight saving, and improvement of strength.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.847-851
• /
• 2010

It was attempted to develop an auto part by over molding injection mold that produces precision products in high productivity with use of an eco-friendly TPE substitute material for NBR. NBR is currently used in motor gear cover, one of the key parts in motor module for auto doors. Gear cover is composed of plastics and rubber mostly today, which requires a two (2) step process for production using two presses of different types. A hot press is used at this time for forming the rubber, which has drawback of requiring a rather long forming time of 400 seconds for one forming process. Even though this difficulty is overcome by reducing production time through employment of multi-cavity molds, time for forming process must be shortened for improvement of the productivity eventually, and the existing method of insert injection for products that have been formed with plastic material must be outgrown. In this point of view, over molding injection using TPE has a big advantage. Forming time is shortened to 54 seconds, and working the two (2) processes in series by one (1) press could solve the durability problem caused by deflection of the plastics, not to mention shortening the process time. Enhancement of productivity by almost 80% and improvement in the accuracy of the product could thus be achieved.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.12
• /
• pp.142-149
• /
• 2002

In this paper, the metal forming process is caused of rise of the unit cost of production in increase of the lead-time and cost because of manufacturing final product through a few the number of processes. Flow control complex forming is proposed to put into formulation in order to apply cold forging from conventional approximate similarity theory, and the forming loads of the real material(AISI 1008) can be calculated by put at the new similarity formula the load by plasticine model material experiment through hub clutch. In order to reduce lead-time and cost the technology is used to manufacture with lower die of this product. By the application synthetic resin as the raw material, it is have the merit such short lead-time, low cost, good surface finish etc., as compared with the machine work.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.53-63
• /
• 1995

In the analysis of metal forming problems, the explicit time integration finite element method, which does not have convergence problems, is frequently used. The present work is to assess the applicability of the explicit time integration finite element method to quasi-static metal forming problems. Compressing analyses of thin-walled tubes and solid cylinders are performed with different loading velocities. The computed buckled profiles of thin walled tubes are compared with the theoretical and experimental ones and it is found that at sufficiently low loading velocity, the explicit time integration finite element method accurately predict quasi-static buckled profiles. When loading volocity is increased, the computed buckled profiles of thin-walled tubes are very sensitive to loading velocity however the computed profiles of solid cylinders are less sensitive to loading velocity. In orther words, the geometrically self-constrained specimens like solid cylinders are less sensitive to loading velocity than the geometrically unconstrained specimens like thin-walled tubes. As a result, it is found that the geometrically self-constrained problems which include the greater part of metal forming problems can be efficiently analyzed with loading velocity control technique.