• Textile Coloration and Finishing
• /
• v.14 no.6
• /
• pp.335-341
• /
• 2002

The physical properties and the dyeability of the nylon S fibers Prepared by high speed spinning according to godet roller draw ratio form 1.1 to 1.6 were investigated. The strains of nylon 6 fibers were decreased against the increase of the godet roller draw ratio. The stresses of nylon 6 fibers were increased with the increase of the godet roller draw ratio. Birefringences, densities and crystallinities of the nylon 6 fibers were increased with the increase of godet roller draw ratio In DSC diagrams, the $\gamma$ form of crystal became dominant at higher godet roller draw ratio. The dye uptakes of C. 1. Acid Blue 113 on the fibers were decreased against the increase of godet roller draw ratio.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.134-143
• /
• 1999

The ship's bows and sterns are assembled with the curved blocks. In shipyards, the roller bending and the line heating or others are being used to fabricate such doubly curved shell. Firstly, the cylinder- or cone-type is formed through the roller bending, and then, the line heating is implemented to form the rest. This paper presents an algorithm to determine the direction for the roller bending and the shape to be formed as fabrication information. The direction for the roller bending is determined with Gauss mapping of the desired surface and the shape to form is calculated by comparing the bent shape with the desired shape.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.79-84
• /
• 2013

Nanoimprint lithography (NIL) is the next generation photolithography process in which the photoresist is dispensed onto the substrate in its liquid form and then imprinted and cured into a desired pattern instead of using traditional optical system. There have been considerable attentions on NIL due to its potential abilities that enable cost-effective and high-throughput nanofabrication to the display device and semiconductor industry. Although one of the current major research trends of NIL is large-area patterning, the technical difficulties to keep the uniformity of the residual layer become severer as the imprinting area increases more and more. In this paper, with the rolling type imprinting process, a mold, placed upon the $2^{nd}$ generation TFT-LCD glass sized substrate($370{\times}470mm^2$), is rolled by a rubber roller to achieve a uniform residual layer. The prediction of residual layer thickness of the photoresist by rolling of the rubber roller is crucial to design the rolling type imprinting process, determine the rubber roller operation conditions-mpressing force & feeding speed, operate smoothly the following etching process, and so forth. First, using the elasticity theory of contact problem and the empirical equation of rubber hardness, the contact length between rubber roller and mold is calculated with consideration of the shape and hardness of rubber roller and the pressing force to rubber roller. Next, using the squeeze flow theory to photoresist flow, the residual layer thickness of the photoresist is calculated with information of the viscosity and initial layer thickness of photoresist, the shape of mold pattern, feeding speed of rubber roller, and the contact length between rubber roller and mold previously calculated. Last, the effects of rubber roller operation conditions, impressing force & feeding speed, on the residual layer thickness are analyzed with consideration of the shape and hardness of rubber roller.

• PNF and Movement
• /
• v.16 no.1
• /
• pp.125-132
• /
• 2018

Purpose: The aim of this study was to investigate the isolated activation ratio of the quadriceps femoris muscle on different support surfaces during squat exercise. Methods: Twenty participants (10 males and 10 females) voluntarily agreed to participate in the research after receiving an explanation about the purpose and process of the study. Each participant performed squat exercises on three different support surfaces (a flat surface, a form roller, and an unstable surface). Muscle activities of the rectus femoris (RF), vastus medialis (VM), and vastus lateralis (VL) were measured by electromyography. The isolated activation ratio of the quadriceps femoris muscle was calculated using the %isolation formula. Results: For the squat exercise, the %isolation value of the VM was significantly higher on the unstable surface than on the flat surface and form roller. In contrast, the %isolation values for the RF for the squat exercise were significantly higher on the flat surface and form roller than on the unstable surface. There was no significant differences in the %isolation values of the VL on the three different surfaces. Conclusion: The findings indicate that squat exercise on different surfaces results in differential activation of the quadriceps femoris muscle, which suggests that squat exercise on a multi-directional unstable surface could increase the isolated activation ratio of the VM.

• Journal of International Academy of Physical Therapy Research
• /
• v.8 no.2
• /
• pp.1182-1189
• /
• 2017

The purpose of this study was conducted with senior women of ages 65 in Community Center to identify effective exercise methods for preventing falling accidents by enhancing balancing skills through aerobic and foam roller exercise programs. There were 24 subjects : 11 aerobics group and 13 foam roller group. 30 minute exercise programs were conducted against both groups 12 times 6 weeks. Various tests, including Time up and go test, Forward reach test, One-leg standing with eyes open/closed and Y-Balance were conducted prior to commencing the exercise program. Wilcoxon's Signed-ranks test was executed to analyze the changes in balance of the aerobic and foam roller exercise group prior to and after the experiment, and Mann-Whitney test was executed to compare the difference between the two groups. The Y-Balance(post. medial) show statistically significant differences in the amount of change before and after exercise between the two groups, except for Timed up and go test, Forward reach test, Y-Balance(ant.), and Y-Balance(post. lateral), which did not showed statistically significant difference (p<0.05). Foam roller exercises are effective methods to enhance the balancing skills in senior women to prevent falling accidents.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1016-1020
• /
• 2001

The spinning is a very effective manufacturing technology for short production runs in a variety of sizes and shapes, because it can form the cross-section or tubular parts various shapes. However extensive experimental and analytical research has not been carried out. In this study, and fundamental experiment was conducted to improve productivity with process parameter such as tool path, angle of roller holder(a), feed rate(v) and corner radius of forming roller(Rr). These factors were selected as variables in the experiment because they were most likely expected to have and effect on spring back. The clearance was controlled in order to achieve the precision product which is comparable to deep drawing one. And also thickness and diameter distribution of a multistage cup obtained by shear spinning process were observed and compared with those of a commercial product produced by conventional deep drawing.

• Journal of the Korean Society for Railway
• /
• v.8 no.3
• /
• pp.276-285
• /
• 2005

This study discussed the effect on rail's axial force due to thermal and seismic loads according to supporting conditions of railway bridges; the considered supporting conditions are 1)simply supported, 2)roller at both ends, and 3)roller with horizontal spring at both ends. Closed form solutions are used to calculate the axial farces on rails. The roller at both ends of a bridge span decreases the compressive axial force on rail due to thermal load compared with the simply supported condition. However, the lateral springs at roller are not helpful to decrease the rail's compressive axial force.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.11
• /
• pp.929-935
• /
• 2015

The long neck flange is used to connect piping arrangements where the lap joint is applied. Generally, the component can be manufactured by welding, but this method is both time and cost intensive. Embrittlement at the heat affected zones was also considered. A spinning method developed to improve the manufacturing process and solve the problems of welding. The flange area of the long neck flange can be formed by changing the direction of the metal flow, from axial to radial, while maintaining pressure by using an outer mold and a lap roller. A modified process was additionally developed using a round roller rather than the outer mold. In this modification, the round roller can form the shape of all sizes of long neck flange. Using these flexible methodologies, the cost to prepare outer molds and the time to install and remove the molds can be significantly reduced.

• Journal of The Korean Radiological Technologist Association
• /
• v.30 no.1
• /
• pp.102-110
• /
• 2004

Purpose : When wish to confirm form of purpose temporomandibularl joint negative plate and degree of displacement, application of own fairness reflex can supply much diagnostic data. Market wished to search usefulness of own fairness roller retroaction en

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.910-920
• /
• 1997

In this paper, some of the critical factors in Necking-In process are investigated using a numerical analysis. The optimal processing parameters are established and applied to the actual processes. FEM analysis is carried out based on elastic-plastic work hardening model using ABAQUS / Standard. The results obtained form the commercially available code ABAQUS / standard are compared with the experimental data and shows a good agreement with experimental data. The purpose of this paper is to search for the relations among the roller angel, feed length, and working force. Stress, strain distribution, displacement and increase in the length of the workpiece are also investigated.