• Transactions of Materials Processing
• /
• v.10 no.7
• /
• pp.558-564
• /
• 2001

An experimental modeling is applied to investigate the formation of forms in molten aluminum By using a specially designed equipment, the effect of process variables, such as the shape of stirrer, stirring velocity and fluid viscosity, on the formation of foams were studied in the glycerine added water. Bubbles formed in water had various diameter from 1 to 10 mm and the number of bubbles was 0 to 20/$cm^2$. It turned out that among various variables the stirring velocity and fluid viscosity played important roles on the formation of bubbles. The results obtained from the model experiment were preyed to be convincible also in the real aluminum foam.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.5
• /
• pp.452-460
• /
• 2008

Anti-foaming agents and foam fences have been used to remove the foam at the outfall of power plants, but there are some problems as consumption of maintenance costs and insufficiency of effect. Therefore, development of the methods how to remove the foam by stable coastal structure has been required. In this study, numerical simulation of air entrainment was carried out to design the submerged outlet structure for reducing foam using curtain walls. The air entrainment rate and the discharge of entrained air change according to the shape of weir and curtain wall. Hence, it is necessary to design the optimum section through comparison of each case. The optimum section which has the maximum rate of foam reduction was determined by the simulation results. In addition, it was found that the flow velocity at the submerged outlet is to be smaller than 1 m/s and the submerged depth of curtain wall is to be taller than height of the submerged outlet section.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.149-158
• /
• 2004

In most RP processes, the inherent stair-stepped surfaces and shrinkage-induced warping of the parts require post processing such as surface finishing. To minimize such defects, VLH-ST, a newly developed RP process, employs a 3.9-mm thick expandable polystyrene (EPS) foam sheet and a hot wire to contour it to have slant linear-interpolated sides. The use of relatively thick sheets for layers, however, limits the process capability of constructing fine details, especially smaller than the layer thickness. This study is focused on the development of a post processing method fo fine details of VLM-ST parts. The post-processing tool was designed to meet all the requirements for the desirable post processing. It adopted a hot wire as a means of melting the EPS foam sheet. Various basic experiments on the post processing were carried out to obtain the optimal process conditions. The dominant process parameters such as the radiated heat input, the tool speed, and the gap between the tool tip and the foam sheet (tool height) were considered in the experiments. The effectiveness of the developed post-processing method fo forming or engraving fine details on the VLM-ST parts has been thus demonstrated. The experiments on engraving several sets of letters, such as CANESM, 인간, and 한국과학기술원, on the EPS foam sheet were carried out. In addition, a flowery shape was engraved on a three-dimensionally curved surface of a pottery-shape VLM-ST part.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.6
• /
• pp.332-349
• /
• 2016

OLAFOAM is the powerful CFD code and is an expanded version of $OpenFOAM^{(R)}$, for wave mechanics simulation. The $OpenFOAM^{(R)}$ does provide many solvers to correspond to each object of the numerical calculation in a variety of fields. OLAFOAM's governing equation bases on VARANS (Volume-Averaged Reynolds-Averaged Navier-Stokes) equation, and the finite volume method is applied to numerical techniques. The program is coded in C++ and run on the Linux operating system. First of all, in this study, OLAFOAM was validated for 1) wave transformation inside porous structure under bore and regular wave conditions, 2) wave transformation by submerged breakwater under regular wave condition, and 3) regular wave transformation and resultant vertical velocity distribution under current by comparison with existing laboratory measurements. Hereafter, this study, which is almost no examination carried out until now, analyzed closely variation characteristics of water surface level, wave height, frequency spectrum, breaking waves, averaged velocity and turbulent kinetic energy around porous submerged breakwater in the wave and current coexisting field for the case of permeable or impermeable rear beach. It was revealed that the wave height fluctuation according to current direction(following or opposing) was closely related to the turbulent kinetic energy, and others.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.658-663
• /
• 2000

Slopping phenomena deteriorate the productivity and the stability of operation in oxygen converter process. To predict and prevent that, it needs reliable perception of the internal state of the oxygen converter chamber. Equipment was developed to measure the dynamic and static behavior of the oxygen-blowing lance 3-dimensionally and the measured signal is analyzed in relation to slopping phenomena. It was found that the behavior of the lance is strongly correlated to the change of slag foam height and the instability of molten steel behavior. So slopping phenomena can be predicted by simultaneously analyzing the measured behavior of the lance and the control factors such as the flow rate of oxygen and the height of lance.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.494-499
• /
• 2011

One of the devices to prevent separated flow over a wing or a flap at high angle of attack is a vortex generator. In the present work, we numerically study the flow around a low-profile or micro vortex generator whose height is less than local boundary layer thickness which can delay separation with a minimum drag penalty owing to its very small wetted surface area. As a first step toward a parametric study to efficiently design this MVG flow control system, we simulate the flow around a single MVG on a flat plate. For the simulation, we employ OpenFOAM with Launder-Sharma ${\kappa}$-epsilon model. The analysis results are validated by comparing with experimental results of a rectangular MVG at an angle of attack of 10 degrees whose height is 20% of local boundary layer. Important results and aspects of this numerical study are discussed. We also simulate the flow around rectangular, triangular and trapezoidal MVGs and the results are compared

• Physical Therapy Korea
• /
• v.28 no.2
• /
• pp.154-160
• /
• 2021

Background: Theoretically, balance is affected by the height of center of mass (COM) during quiet standing. However, no one examined this in humans with variables derived from the center of pressure (COP). Objects: We have conducted balance experiment to measure COP data during quiet standing, in order to examine how the COP measures were affected by the height of COM, vision, floor conditions, and gender. Methods: Twenty individuals stood still with feet together and arms at sides for 30 seconds on a force plate. Trials were acquired with three COM heights: 1% increased or decreased, and not changed, with two vision conditions: eyes closed (EC) and eyes open (EO), and with two floor conditions: unstable (foam pad) and stable (force plate) floor. Outcome variables included the mean distance, root mean square distance, total excursion, mean velocity, and 95% confidence circle area. Results: All outcome variables were associated with the COM height (p < 0.0005), vision (p < 0.0005), and floor condition (p < 0.003). The mean velocity and 95% confidence circle area were 5.7% and 21.8% greater, respectively, in raised COM than in lowered COM (24.6 versus 23.2 mm/s; 1,013.4 versus 832.3 mm²). However, there were no interactions between the COM height and vision condition (p > 0.096), and between the COM height and floor condition (p > 0.183) for all outcome variables. Furthermore, there was no gender difference in all outcome variables (p > 0.186). Conclusion: Balance was affected by the change of COM height induced by a weight belt in human. However, the effect was not affected by vision or floor condition. Our results should inform the design of balance exercise program to improve the outcome of the balance training.

• Horticultural Science & Technology
• /
• v.31 no.2
• /
• pp.179-185
• /
• 2013

This study was carried out to find a reasonable irrigation method of a nutrient solution for the phenolic foam slab (foam LC) used in a trial experiment to substitute the rockwool slab in the production of paprika (Capsicum annuum 'Veyron'). 100, 90, and 80 mL of a nutrient solution was supplied per plant each time when the accumulated radiation reached to 100, $90J{\cdot}cm^{-2}$, and they were named as the 100-100, 90-90, and 90-80 treatment, respectively. The drain percentage per plant of the 100-100 treatment was high by 33.8% in rockwool and 36.7% in foam LC (Lettuce Cube) and that of 90-80 treatment was low by 30.4% and 33.7%. The water content and EC of the rockwool slab were maintained in the range of 63.6-68.9% and $4.4-5.1mS{\cdot}cm^{-1}$, while those of the foam LC slab were in the range of 52.9-58.8% and $5.5-6.5mS{\cdot}cm^{-1}$. The plant height and leaf size of the 100-100 and 90-90 treatments increased in a similar manner, while those of the 90-80 treatment decreased and those of the rockwool were greater than those of the foam LC. The fruit size and weight of the 100-100 and 90-90 treatments were similarly bigger and heavier than those of the 90-80 treatment. The number of fruits harvested per plant was the greatest in the 90-80 treatment with 8 and 8.3 fruits in the rockwool and foam LC. The number of marketable fruits in the rockwool and foam LC was the greatest with 18.1 and 18.2, respectively, in the 90-90 treatment, while that in the 90-80 treatment was 17.2 and 16.8, respectively. The number of unmarketable fruits of the 90-80 treatment was the greatest (1.7-1.8 fruits per plant) in both the rockwool and foam LC, and most of them were small sized or blossom end rot fruits. The yield of the 90-90 treatment was the greatest among the irrigation.

• Applied Chemistry for Engineering
• /
• v.30 no.2
• /
• pp.241-246
• /
• 2019

In this paper, reactive surfactants were synthesized by using acrylic acid or 3-butenoic acid as nonionic surfactants, polyoxyethylene(23) lauryl ether (Brij 35) and polyoxyethylene(20) stearyl ether (Brij S20). The synthesis of surfactants was confirmed by FT-IR and $^1H$-NMR. The surface tension, emulsifying property, and foam power and stability were also measured. The surface tension value was 35~41 dyne/cm at an critical micelle concentration (cmc) which was measured as $1.0{\times}10^{-4}{\sim}9.7{\times}10^{-5}mol/L$ using a surface tension method. The emulsifying power of synthesized surfactant was measured with benzene, soybean oil and monomer. Also, the initial height of the bubbles and the height after 5 minutes were measured and the values were compared with each other.

• 한국생물공학회:학술대회논문집
• /
• 2003.04a
• /
• pp.371-373
• /
• 2003

In experiments on sea water, it took longer to reach almost steady state and the foam heights were increased as increasing initial protein concentration. The foam height was increased with the decrease of the pore size. G3, G4, and air stone were similar. It was increased with the increase in the superficial air velocity (SAV) and it was efficient when the SAV is $0.7{\sim}0.8\;cm/sec$. The optimum pH condition is weak acid and weak base region. The influence of salts, $NaHCO_3$, was not that significant due to NaCl in the sea water.