• International Journal of Fluid Machinery and Systems
• /
• 제8권2호
• /
• pp.94-101
• /
• 2015

To investigate the influence of blade profiles on cavitation behavior in impeller of centrifugal pump, a centrifugal pump with five different blade profiles impellers are studied numerically. The impellers with five different blade profiles (single arc, double arcs, triple arcs, logarithmic spiral and linear-variable angle spiral) were designed by the in-house hydraulic design code using geometric parameters of IS 150-125-125 centrifugal pump. The experiments of the centrifugal pump have been conducted to verify numerical simulation model. The numerical results show that the blade profile lines has a weak effect on cavitation inception near blade inlet edge position, however it has the key effect on the development of sheet cavitation in impeller, and also influences the distribution of sheet cavitation in impeller channels. A slight changing of blade setting angle will induce significant difference of cavitation in impeller. The sharp changing of impeller blade setting angle causes obvious cavitation region separation near the impeller inlet close to blade suction surface and much more flow loss. The centrifugal pump with blade profile of setting angle gently changing (logarithmic spiral) has the super cavitation performance, which means smaller critical cavitation number and lower vapor cavity volume fraction at the same conditions.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3031-3037
• /
• 1996

In cold forming processes, due to high working pressure action on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. Die wear affects the tolerances of formed parts, metal flow and costs of process etc. The only way to control these failures into devlop methods which allow prediction of die wear and which are suited to be used in the design state in order to optimize the process. In this paper, the forming propcesses that involve cold forward extrusion and wire drawing were simulated by rigid plastic finite element method and its output were used for predicting die wear by Archard wear model. The simulation results were compared with the measured worn dies.

• 한국정밀공학회지
• /
• 제28권3호
• /
• pp.349-356
• /
• 2011

This paper replaces a conventional austenitic stainless steel sheet to a ferritic stainless steel for the cost reduction of a pulsator cover of a washing machine. However, ferritic stainless steel has poor formability in comparison with austenitic one. The low formability of ferritic steel results in problems during stamping such as fracture, wrinkling, shape inaccuracy and so on. Design modification of the stamping tool is carried out with the aid of the finite element analysis for multistage stamping process of the pulsator cover. The simulation results show that fracture occurs on top of the product while wrinkles are generated by the excess metal near the wing part. Modification of the initial stamping die is performed to improve metal flow and to eliminate problems during the stamping process. Simulation with the modified design fully demonstrates that safe forming is possible without inferiorities.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.248-258
• /
• 1992

Three-dimensional rigid-plastic finite element formulation based on the membrane theory was described and a computer program for large deformation analysis was developed. In the formulation, normal and planar anisotropy of sheet material and rotation of the principal axes of anisotropy was taken into consideration. Sheet metal was assumed to be rigid-plastic material obeying Hill's quadratic yield criterion and its associated flow rule. Deep drawing process, as a preliminary test, for normal anisotropic material was analyzed in order to examine the validity of developed finite element program. The results were consistent with the existing finite element solutions or experimental data. The present study was mainly concerned with the influence of planar anisotropy on deformation behaviour. Finite element analysis and experiment were carried out for the whole process of deep drawing of planar anisotropic material. The computational and experimental results on the shape of ear, strain distribution and punch load were in good agreement.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.87-90
• /
• 2005

The drawbead is used to control the material flow into the die and increase the forming quality during the binder wrap process and the stamping process in the sheet metal forming. Drawbead restraining force (DBRF) is controlled by geometrical parameters and influenced by process parameters such as friction coefficient and blank thickness. In order to inspect the effect of process parameters, parameter studies are performed with the variation of parameters using finite element model of drawbead which is utilized reliably for the calculation of the drawbead restraining force. Drawbead analysis is carried out with 2-D plane-strain element and 3-D shell element. After the verification of the accuracy of the drawbead model with 3-D shell element, it is utilized to the prediction and the investigation of the effect of process parameters. The result of parameter studies can be utilized to the die design in the tryout stage.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2009년도 춘계학술발표논문집
• /
• pp.13-17
• /
• 2009

본 논문에서는 학습집중력을 향상 시킬 수 있는 시트를 제작 하였다. 학습집중력의 향상을 입증하기 위하여 인체내에 존재하고 있는 조영제를 이용하여 공간적 시간적 해상도가 뛰어나고 비침습적으로 뇌기능을 측정할 수 있는 기능적 자기공명영상을 획득하고 뇌파측정을 한 결과 기억작용과 관련 있는 전두엽 부근의 뇌혈류량의 활성화를 확인할 수 있었고 뇌파 측정 분석결과 절대알파파와 절대베타파의 비율에서 유의할 만한 변화를 확인하였다. 기능적자기공명 영상은 뇌의 생리기능적 역할을 규명 의학적으로 수술 전후 장애를 방지하고 예방하는데 활용하고 있으며 뇌신경망의 가시화로 학습 집중력 등과 같은 뇌와 관련된 제품을 개발하는데 많은 연구가 이루어질 것이다.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.507-512
• /
• 2016

Expensive silver powder is used to form electrodes in most IT equipment, and recently, many attempts have been made to lower manufacturing costs by developing powders with Ag-Ni or Ag-Cu core-shell structures. This study examined the sintering behavior of Ag-Ni electrode powder with a core-shell structure for silicon solar cell with high energy efficiency. The electrode powder was found to have a surface similar to pure Ag powder, and cross-sectional analysis revealed that Ag was uniformly coated on Ni powder. Each electrode was formed by sintering in the range of $500^{\circ}C$ to $800^{\circ}C$, and the specimen sintered at $600^{\circ}C$ had the lowest sheet resistance of $5.5m{\Omega}/{\Box}$, which is about two times greater than that of pure Ag. The microstructures of electrodes formed at varying sintering temperatures were examined to determine why sheet resistance showed a minimum value at $600^{\circ}C$. The electrode formed at $600^{\circ}C$ had the best Ag connectivity, and thus provided a better path for the flow of electrons.

• 한국전기전자재료학회논문지
• /
• 제22권1호
• /
• pp.81-85
• /
• 2009

We has been analysed optical properties of OLED(organic light emitting diode) and characteristics of ITO(Indium Tin Oxide) in terms of $O_2$ plasma treatment for manufacturing high efficiency OLED, RF power of $O_2$ plasma was changed 25, 50, 100, 200 W. $O_2$ gas flow, gas pressure and treatment time were fixed. Sheet resistance and surface roughness of ITO were measured by Hall-effect measurement system and AFM, respectively. The ranges of sheet resistance and surface roughness were $5.5{\sim}6,06\;{\Omega}$ and $2.438{\sim}3.506\;nm$ changing of RF power, respectively, PM(Passive Matrix)OLED was fabricated with the structure of ITO(plasm treatment)/TPD($400\;{\AA}$)/$Alq_3(600\;{\AA})$/LiF($5\;{\AA}$)/Al($1200\;{\AA}$). Turn-on voltage of PMOLED was 7 V and luminance was $7,371\;cd/m^2$ at the RF power of 25 W, $O_2$ plasma treatment of ITO surface was result in lowering the operating voltage and improving luminance of PMOLED.

• 전기학회논문지
• /
• 제59권7호
• /
• pp.1255-1258
• /
• 2010

In this paper, the $CoSi_2$ thin films with thicknesses of about $5{\mu}m$ were deposited on n-type silicon (111) substrates by RF magnetron sputtering method using a $CoSi_2$ target (99.99%). The flow rate of argon of 50 sccm, substrate temperature of $100^{\circ}C$, RF power of 60 watts, deposition time of 30 minutes, and the vacuum of $1\times10^{-6}$ Torr. The annealing treatments of the $CoSi_2$ thin film were performed from 500, 700 and $900^{\circ}C$ for 1h in air ambient by an electric furnace. In order to investigate the $CoSi_2$ thin film X-ray diffraction patterns were measured using the X-ray diffractometer (XRD). The structure of the thin films were investigated by using scanning the electron microscope (SEM) were used for review. The surface morphology of the thin films was measured with a atomic force microscopy (AFM). Temperature dependence of sheet resistivity and property of Hall effect was measured in the $CoSi_2$ thin film.

• 한국지반공학회지:지반
• /
• 제8권3호
• /
• pp.37-50
• /
• 1992

지진으로 인한 액상화현상은 토목구조물에 막대한 피해를 주고 있다. 본 연구에서는 액상화 현상에 대란 대책을 연구할 목적으로 모형 항만구조물을 대상으로 하여 진동대 실험을 실시하였다. 액상화현상으로 항만구조물에 발생하는 과잉변형을 방지하기 위하여 보강구간을 설치하고 그 효과에 대하여 검토하였다. 제방, 이중 널말뚝벽과 앵커 구조물의 진동대 실험을 통하여, 액상화 지반의 유동변형에 대한 특성과 보강범위에 대한 정량적 자료를 얻었다. 항만구조물을 보호하기 위한 보강구간의 범위는 진동가속도의 크기에 따라 다르다. 실험을 통하여 얻어진 구조물의 과잉변형을 보강구간의 범위와 진동가속도의 크기에 따라 나타내었다.