• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.357-366
• /
• 1986

본 연구에서는 3공피토우관 및 열선유속계를 사용하여 벽에 평행한 2차원 난류제트의 난류량들을 측정하였고, 스캐니 밸브를 이용하여 벽면아력분포를 측정함 으로써 재순환 영역을 포함한 전체유동장에서의 유동특성을 고찰하였다. 또한 잘 알려진 표준 k-.epsilon. 난류모형 및 유선곡률을 고려한 수정된 k-.epsilon. 난류모형을 이용하여 측정 수치해석을 수행하였다.

• 대한기계학회논문집B
• /
• 제36권9호
• /
• pp.923-930
• /
• 2012

입구유동 가진이 있는 층류 후향계단 유동에서 Pr수의 변화에 따른 열전달 특성변화를 조사하기 위하여 비정상 수치해석을 수행하였다. 입구는 가진주파수와 가진진폭의 변화에 따른 교란이 주어졌고, 온도함수의 물성치가 적용되었다. 열전달 변화에 대한 다양한 특징들이 열경계층 변화에 의해서 설명되었다. 물성치가 일정한 경우와 비교하였을 때, 물성치가 온도의 함수성이 있는 경우 Pr < 1인 조건에서 열전달은 감소하였고, 반대로 Pr > 1인 조건에서 열전달은 증가하였다. 또한 가진진폭이 증가함에 따라 계단 후류 바닥면에서 열전달도 증가하였다. 그렇지만 가진주파수 변화의 경우 St < 0.2인 조건에서 열전달이 크게 증가하는 특정주파수 영역이 존재하였다. 특히, 열전달의 증가는 재부착 길이의 rms값의 변동정도와 밀접한 관련이 있음을 보여주었다.

• Asian Journal of Atmospheric Environment
• /
• 제12권1호
• /
• pp.47-58
• /
• 2018

The aim of this work is to investigate the effect of atmospheric stability on near-field pollutant dispersion from rooftop emissions of a single cubic building using computational fluid dynamics (CFD). This paper used the shear stress transport (here after SST) k-${\omega}$ model for predicting the flow and pollutant dispersion around an isolated cubic building. CFD simulations were performed with two emission rates and six atmospheric stability conditions. The results of the simulations were compared with the data from wind tunnel experiments and the result of simulations obtained by previous studies in neutral atmospheric condition. The results indicate that the reattachment length on the roof ($X_R$) obtained by computations show good agreement with the experimental results. However, the reattachment length of the rooftop of the building ($X_F$) is greatly overestimated compared to the findings of wind tunnel test. The result also shows that the general distribution of dimensionless concentration given by SST k-${\omega}$ at the side and leeward wall surfaces is similar to that of the experiment. In unstable conditions, the length of the rooftop cavity was decreased. In stable conditions, the horizontal velocity in the lower part around the building was increased and the vertical velocity around the building was decreased. Stratification increased the horizontal cavity length and width near surface and unstable stratification decreased the horizontal cavity length and width near surface. Maintained stability increases the lateral spread of the plume on the leeward surface. The concentration levels close to the ground's surface under stable conditions were higher than under unstable and neutral conditions.

• Wind and Structures
• /
• 제34권1호
• /
• pp.81-90
• /
• 2022

To better understand the vortex-induced vibration (VIV) characteristics of a 5:1 rectangular cylinder, the distribution of aerodynamic force and the non-dimensional power spectral density (PSD) of fluctuating pressure on the side surface were studied in different VIV development stages, and their differences in the stationary state and vibration stages were analyzed. The spanwise and streamwise correlations of surface pressures were studied, and the flow field structure partitions on the side surface were defined based on the streamwise correlation analysis. The results show that the variation tendencies of mean and root mean square (RMS) pressure coefficients are similar in different VIV development stages. The RMS values during amplitude growth are larger than those at peak amplitude, and the smallest RMS values are observed in the stationary state. The spanwise correlation coefficients of aerodynamic lifts increase with increase of the peak amplitude. However, for the lock-in region, the maximum spanwise correlation coefficient for aerodynamic lifts occurs in the VIV rising stage rather than in the peak amplitude stage, probably due to the interaction of vortex shedding force (VSF) and self-excited force (SEF). The streamwise correlation results show that the demarcation point positions between the recirculation region and the main vortex region remain almost constant in different VIV development stages, and the reattachment points gradually move to the tailing edge with increasing amplitude. This study provides a reference to estimate the demarcation point and reattachment point positions through streamwise correlation and phase angle analysis from wind tunnel tests.

• 대한기계학회논문집
• /
• 제14권6호
• /
• pp.1603-1612
• /
• 1990

본 연구에서는 5개의 원관으로 이루어진 일행관군에서의 원관 주위의 유동특 성의 해명과 유동장이 열전달에 미치는 영향등을 보다 상세히 밝히는데 목적이 있으며, 이를위해 원관의 표면압력, 관 주위의 유동장의 평균속도 및 난류강도, 관의 표면온도 등을 측정하였다.

• 대한기계학회논문집B
• /
• 제29권5호
• /
• pp.590-598
• /
• 2005

The present study has been conducted to investigate the effect of discrete ribs and rotation on heat/mass transfer characteristics in a two-pass square duct with $90^{\circ}-rib$ turbulators. The rib turbulator has a square cross section of 1.5 mm. The rib height-to-hydraulic diameter ratio $({e/D_{h})$ is 0.056, and the rib pitch-to-rib height ratio (p/e) is 10. The gap width is the same as the rib height. The rotation number ranges from 0.0 to 0.2 while Reynolds number is fixed to 10,000. In a stationary duct, the heat/mass transfer on the surfaces with discrete ribs is enhanced because the gap flow promotes local turbulence and flow mixing near the ribbed surface. In a rotating duct, the gap flow affects differently the heat/mass transfer on leading and trailing surfaces with discrete ribs. On the leading surface of the first pass, heat/mass transfer is increased due to the gap flow. On the trailing surface of the first pass, however, heat/mass transfer is decreased because the gap flow disturbs reattachment of main flow. The phenomenon, that is, the difference of heat transfer between the leading and the trailing surfaces is distinctly presented by rotation.

• 대한기계학회논문집B
• /
• 제30권5호
• /
• pp.446-456
• /
• 2006

The effect of relative position of the stationary turbine blade for the fixed vane has been investigated on blade tip and shroud heat transfer. The local mass transfer coefficients were measured on the tip and shroud fur the blade fixed at six different positions within a pitch. A low speed stationary annular cascade with a single turbine stage was used. The chord length of the tested blade is 150 mm and the mean tip clearance of the blade having flat tip is 2.5% of the blade chord. A naphthalene sublimation technique was used for the detailed mass transfer measurements on the tip and the shroud. The inlet flow Reynolds number based on chord length and incoming flow velocity is fixed to $1.5{\times}10^5$. The results show that the incoming flow condition and heat transfer characteristics significantly change when the relative position of the blade changes. On the tip, the size of high heat/mass transfer region along the pressure side varies in the axial direction and the difference of heat transfer coefficient is up to 40% in the upstream region of the tip because the position of flow reattachment changes. On shroud, the effect of tip leakage vortex on the shroud as well as tip gap entering flow changes as the blade position changes. Thus, significantly different heat transfer patterns are observed with various blade positions and the periodic variation of heat transfer is expected with the blade rotation.

• 대한기계학회논문집B
• /
• 제29권4호
• /
• pp.495-503
• /
• 2005

Experiments were conducted in a low speed stationary annular cascade to investigate local heat transfer characteristics on the tip and shroud and the effect of inlet Reynolds number on the tip and shroud heat transfer. Detailed mass transfer coefficients on the blade tip and the shroud were obtained using a naphthalene sublimation technique. The turbine test section has a single stage composed of sixteen guide vanes and blades. The chord length and the height of the tested blade are 150 mm and about 125 mm, respectively. The blade has flat tip geometry and the mean tip clearance is about $2.5{\%}$of the blade chord. The inlet flow Reynolds number based on chord length and incoming flow velocity is changed from $1.0{\times}10^{5}\;to\;2.3{\times}10^{5}.$ to investigate the effect of Reynolds number. Flow reattachment after the recirculation near the pressure side edge dominates the heat transfer on the tip surface. Shroud surface has very intricate heat/mass transfer distributions due to complex flow patterns such as acceleration, relaminarization, transition to turbulent flow and tip leakage vortex. Heat/mass transfer coefficient on the blade tip is about 1.7 times as high as that on the shroud or blade surface. Overall averaged heat/mass transfer coefficients on the tip and shroud are proportional to $Re_{c}^{0.65}\;and\;Re_{c}^{0.71},$ respectively.

• 대한기계학회논문집B
• /
• 제20권8호
• /
• pp.2593-2600
• /
• 1996

A modified k-$\varepsilon$ turbulence model having a generality is proposed in the present study, in which the constant $C_{\varepsilon2}$in the $\varepsilon$-equation is simply changed as a functional form of a new parameter both satisfying the tensor invariant condition and representing the extra straining effect on complex shear flows. With this model turbulent shear flows over two-dimensional obstacles placed in a channel are numerically studied for different blockage ratios and aspect ratios. Comparing with the available experimental data, the predicted results with the present model provide definite improvements over the standard model's results and work fairly well with the experimental data on the size of the recirculation zone, as well as mean velocity, wall static pressure, turbulent kinetic energy and Reynolds stresses.

• 기계저널
• /
• 제33권9호
• /
• pp.803-810
• /
• 1993

벽면에서의 전단응력 분포와 유동장 내에서의 3차원 유동 요소를 추적하는 유동가시화 기법중 에서 몇 가지를 그 응용 예와 함께 살펴보았다. 3차원 유동의 주요 특징들과 한계유선(limiting streamlines)을 관찰하기 위해서는 oil and lampblack 기법이 충분하나 유속이 작거나 유동의 방향이 분명하지 않은 곳에서는 ink dot 기법을 적용하는 것이 좋다. Oil and lampblack 기법은 실험하고자 하는 유동의 조건에 따라 기름과 분말의 혼합비, 기름의 점도 등을 잘 선택하여야 한다. 안장점(Saddle point) 이나 재부착선(reattachment line)과 같이 성격상 중요한지점을 찾기 위해서는 털실 프로브(single tuft probe)가 유용하게 쓰이며, 이는 또 유동내에서 와동의 존재와 위치를 찾는데 쓰이기도 한다. 수치해석 결과 얻을 수 잇는 속도벡터와 같이 비교적 넓은 유동 장을 한눈에 관찰하기 위해서는 털실 격자망 (tuft grid)을 사용할 수 있으며 각 털실은 그 지 점세서의 유동의 방향과 그 안정성(steadiness)를 나타내준다. 이러한 유동가시화 방법들은 각 유동의 특성에 맞는 적절한 조건을 맞추기 위해서 많은 시행착오를 거쳐야 하며, 하나의 만족 스러운 결과를 얻기 위해서는 많은 기술과 시간과 연습을 요구하고 있어서 다른 정량적인 측정 기술과 더불어 커다란 노력과 관심을 기울여서 발전시켜야만 할 것이다.