• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.105-117
• /
• 2015

The purpose of this study is to develop a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were experimentally performed on one unreinforced beam-column specimen and two reinforced specimens with L-type precast wall panels. The results were analyzed to find that the specimen with anchored connection experienced shear failure, while the other specimen with steel plate connection principally manifested flexural failure. The ultimate strength of the specimens was determined to be the weaker of the shear strength of top connection and flexural strength at the critical section of precast panel. In this setup of L-type panel specimens, if a push loading is applied to the reinforced concrete column on one side and push the precast concrete panel, a pull loading from upper shear connection is to be applied to the other side of the top shear connection of precast panel. Since the composite flexural behavior of the two members govern the total behavior during the push loading process, the ultimate horizontal resistance of this specimen was not directly influenced by shear strength at the top connection of precast panel. However, the RC column and PC wall panel member mainly exhibited non-composite behavior during the pull loading process. The ultimate horizontal resistance was directly influenced by the shear strength of top connection because the pull loading from the beam applied directly to the upper shear connection. The analytical result for the internal shear resistance at the connection pursuant to the anchor shear design of ACI 318M-11 Appendix-D except for the equation to predict the concrete breakout failure strength at the concrete side, principally agreed with the experimental result based on the elastic analysis of Midas-Zen by using the largest loading from experiment.

• 콘크리트학회논문집
• /
• 제16권1호
• /
• pp.94-101
• /
• 2004

본 연구에서는 인장측 단면이 손상된 철근 콘크리트 보를 변형 에폭시계 모르타르를 사용하여 보수한 후의 휭 거동 특성의 변화 및 파괴형태, 내력 보강 효과 등에 대해 실험적 연구를 수행함으로써 보수 방법에 대한 기초 자료를 확보하고자 하였다. 이를 위해 실험의 주 변수로 손상깊이 2종류, 보수길이 3종류에 대하여 각각 실험변수에 적합한 시험체를 제작하였으며, 기본 시험체를 포함하여 총 7개의 시험체를 제작?실험하였다. 실험 방법은 4점 가력 방법으로 파괴시까지 가력하였으며, 실험결과로 극한하중, 하중-처짐 관계 및 파괴모드에서의 변수의 영향에 따른 시험체의 휨거동에 대해 분석하였다. 또한, 실험연구의 결과를 바탕으로 비선형 해석을 통하여 보수재료의 인장 강도에 따른 보수 후 부재의 구조 거동에 대한 연구를 수행하였다. 연구 결과, 보수 길이와 깊이가 증가하면 보수재료의 인장강도가 부재의 구조 거동에 미치는 영향이 크므로 보수설계 단계에서 보수 면적을 결정할 때 이를 고려해야 하는 것으로 나타났다. 또한, 해석결과로부터 부재의 취성적인 파괴를 방지하기 위해서는 보수재료의 인장강도가 콘크리트의 4배 이하인 재료를 사용하는 것이 적절한 것으로 판명되었다.

• 대한치과보철학회지
• /
• 제28권1호
• /
• pp.165-191
• /
• 1990

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoration, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of $5{\times}5{\times}25mm$. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respecitvely. Porcelain glass transition temperatures and expansion values were derived alloy-porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal-porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated: 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than that of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly 5. Alloy-porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.111-137
• /
• 1991

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoratoin, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of 5 x 5 x 25mm. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respectively. Porcelain glass transition temperatures and expansion values were derived alloy- porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal- porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated : 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly. 5. Alloy- porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• 접착 및 계면
• /
• 제2권2호
• /
• pp.1-10
• /
• 2001

Epoxy molding compound (EMC)에 사용되는 실리카를 13.56 MHz 플라즈마 중합 장치를 이용하여 코팅하였으며, 코팅시간, 플라즈마전압, 내부압력을 변화시키면서 코팅조건을 최적화하였다. 플라즈마 중합 코팅용 단량체로는 1.3-diaminopropane, allylamine, pyrrole, 1,2-epoxy-5-hexene, allylmercaptan 및 allylalcohol을 사용하였으며, 코팅된 실리카의 접착성은 굴곡강도 측정으로 분석하였다. 또한 열팽창 계수 (CTE) 및 수분 흡습률 변화를 측정하였으며, 파괴 단면을 SEM으로 분석하여 접착 특성을 규명하고자 하였다. 플라즈마 중합 코팅된 실리카와 에폭시 수지간의 접착기구를 규명하기 위하여 플라즈마 고분자 코팅을 FT-IR로 분석하였으며, DSC를 이용하여 코팅된 실리카와 에폭시 수지간의 반응성도 고찰하였다. 1,3-diaminopropane과 allylamine으로 코팅된 실리카를 함유하는 EMC는 비교시편에 비하여 높은 굴곡강도, 낮은 CTE 및 낮은 흡습율을 보였으며, SEM 분석 결과 100% cohesive failure 거동을 나타내었다. 이러한 결과는 고분자 코팅내의 아민 반응기와 에폭시 수지간의 화학적 결합에 의한 것으로 판단되며, FT-IR 및 DSC 분석결과와 부합된다.

• 콘크리트학회논문집
• /
• 제29권4호
• /
• pp.345-351
• /
• 2017

이 연구에서는 철근콘크리트 기둥의 휨 연성에 대한 보조 띠철근으로서 ACI 318-14에서 제시하는 크로스타이의 대체로서 V-타이 보조 띠철근의 효율성을 평가하였다. 작용 축하중비를 주요 변수로 일정 축하중과 반복 횡하중을 받는 기둥에서 파괴모드 및 횡하중-횡변위 관계를 측정하였다. 기둥의 최대 휨 내력 이후, 크로스타이의 $90^{\circ}$ 갈고리가 서서히 열리면서 주철근의 조기 좌굴 및 코어 콘크리트의 심각한 손상을 동반한 반면, V-타이의 뽑힘 현상은 기둥의 파괴 시까지 나타나지 않았다. 최대 내력의 80% 시점에서 V-타이 기둥의 일손상 지수 값은 크로스타이 기둥에 비해 축력비가 0.25, 0.4 및 0.55일 때 각각 2.4배, 2.3배 및 5.2배 높았다. 즉, 기둥의 휨 연성에 대한 기존 크로스타이 대비 V-타이의 효율성은 축력비가 높을수록 현저하였다.

• 콘크리트학회논문집
• /
• 제27권2호
• /
• pp.157-167
• /
• 2015

고속 비상체에 의한 충격을 받는 시멘트 복합체는 표면관입, 배면박리 및 관통 등 국부적인 파괴거동을 보이며, 섬유혼입에 의한 휨인성의 향상으로 인해 배면파괴를 억제할 수 있다. 이에 섬유보강 시멘트 복합체의 내충격 성능에 관한 연구가 진행되고 있으며, 다양한 종류의 섬유보강재가 개발되고 있다. 섬유보강재의 종류에 따라 섬유와 매트릭스의 부착성능, 비표면적, 혼입개체수 등이 다르기 때문에 섬유보강 시멘트 복합체의 역학특성 및 고속 충격에 의한 내충격 성능의 향상에 미치는 효과에 대하여 검토할 필요가 있다. 본 연구에서는 성상 및 물성이 다른 강섬유(Steel fiber), 폴리아미드(Polyamide), 나일론(Nylon) 및 폴리에틸렌(Polyethylene)섬유를 혼입하여 섬유 종류에 따른 휨인성의 향상과 고속 비상체 충돌에 대한 파괴저감효과에 대하여 평가하였다. 그 결과, 혼입섬유의 가교작용에 의한 응력의 재분배 및 균열발생의 억제로 인해 휨인성이 향상되었으며, 고속충격에 의한 배면파괴를 억제할 수 있었다. 또한, 동일 충격에너지에서의 배면파괴한계두께를 감소시킬 수 있어 방호시설물에 적용할 경우 부재두께의 저감이 가능할 것으로 판단된다. 한편, 강섬유보강 시멘트복합체의 경우 배면박리가 발생하였으나, 섬유와 매트릭스의 부착에 의한 일부 파편의 박리가 억제되었으며, 합성섬유보강 시멘트복합체는 섬유의 혼입개체수가 많아, 고속충격에 의한 충격파의 상쇄작용 및 에너지 분산에 의한 미세균열이 발생해 배면파괴억제효과가 큰 것으로 판단된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권5호
• /
• pp.149-156
• /
• 2021

FRP 보강근은 철근-콘크리트 부재의 부식 문제를 해결하기 위해 제안되어왔으나, FRP는 높은 인장강도, 낮은 연성 및 선형 탄성 거동으로 인해 하중이 전달될 때 콘크리트와 보강재 사이의 부착 메커니즘이 다르다. 그러므로, FRP-Rebar와 콘크리트 사이의 부착 거동은 주의 깊게 검토해야 한다. 이를 위해 직접 인발 실험이 간단하게 부착 거동을 평가할 수 있으므로 사용됐으나, 직접인발의 실험 결과는 실제 FRP를 보강근으로 사용한 콘크리트 부재의 휨-부착 거동과 다르다. 그러므로 실제 휨-부착 거동을 평가할 방안이 필요하다. 본 연구에서는 FRP를 보강근으로 사용한 콘크리트 부재의 휨-부착 거동에 대한 평가방법을 검토하고 비교하였다. 그 결과, 겹침이음이 있는 부재의 실험 방법이 실제 휨-부착 특성을 잘 반영할 수 있으나 다른 실험방법보다 시험체의 단면 및 지간이 커야 하고 시험체의 설계 및 해석이 복잡하다. 한편, 아치가 있는 부재 실험은 모멘트 팔길이의 변화를 무시하는 평형 방정식을 기반으로 한 힌지가 있는 부재 실험과 달리 콘크리트의 영향을 반영할 수 있으나, 휨-부착에 의한 파괴 이전에 전단파괴의 우려가 있다.

• Restorative Dentistry and Endodontics
• /
• 제44권4호
• /
• pp.44.1-44.11
• /
• 2019

Objectives: To compare the flexural cyclic fatigue resistance and the length of the fractured segments (FLs) of recently introduced M-Pro rotary files with that of RaCe rotary files in curved canals and to evaluate the fracture surface by scanning electron microscopy (SEM). Materials and Methods: Thirty-six endodontic files with the same tip size and taper (size 25, 0.06 taper) were used. The samples were classified into 2 groups (n = 18): the M-Pro group (M-Pro IMD) and the RaCe group (FKG). A custom-made simulated canal model was fabricated to evaluate the total number of cycles to failure and the FL. SEM was used to examine the fracture surfaces of the fragmented segments. The data were statistically analyzed and comparisons between the 2 groups for normally distributed numerical variables were carried out using the independent Student's t-test. A p value less than 0.05 was considered to indicate statistical significance. Results: The M-Pro group showed significantly higher resistance to flexural cyclic fatigue than the RaCe group (p < 0.05), but there was no significant difference in the FLs between the 2 groups (p ≥ 0.05). Conclusions: Thermal treatment of nickel-titanium instruments can improve the flexural cyclic fatigue resistance of rotary endodontic files, and the M-Pro rotary system seems to be a promising rotary endodontic file.