• 제목/요약/키워드: finte element

검색결과 19건 처리시간 0.027초

특이점이 고려된 비오-사바르법을 이용한 3차원 코일의 자계 해석 (3-Dimensional Magnetic Field Analysis of Coil Using Biot-Savart Law Considering Singularity)

  • 송호준;이향범
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
    • /
    • pp.104-106
    • /
    • 2005
  • In this paper, 3-dimensional magnetic field of coil is analyzed by using biot-sarvart law considering singularity. The RMSP(reduced magnetic scalar potential) arc employed in order to reduce the number of unknown variables in FEM(Finte Element Analysis) or BEM(Boundary Element Method). It Is necessary to calculate magnetic field of souce current when RMSP is used. Biot-savart law is generally used. it is difficult to calculate the field when the source point is in inside the coil. To integrate using gaussian quadrature, the cross section of coil is divided considering the position of field point when field point is inside coil. The proposed method shows good agreement of magnetic field compared with FEMLAB, OPERA3D.

  • PDF

편심(偏心) 보강평판(補强平板)의 강도(强度) 해석(解析) (Strength Analysis of Eccentrically Stiffened Plates by Finte Element Method)

  • 김창렬;김재복
    • 대한조선학회지
    • /
    • 제17권4호
    • /
    • pp.1-11
    • /
    • 1980
  • Stiffened plates are commonly used as a component of ship's structures. Most frequently symmetrically stiffened plates are used, but some of stern structures and any specified parts are often constructed with eccentrically stiffened plates. The problems of these eccentrically stiffened plates have been studied rarely, and the results of eccentricity effect of eccentrically stiffened plates are not available. This paper deals with the analysis of eccentrically stiffened plates in the linear elastic range. The derivation of the stiffness matrix was carried out by finite element method for which the isoparametric element was adopted. To show the effect of eccentricity, the deflection at the center under the uniformly distributed and the concentrated load of simply supported and clamped plate models are computed respectively in accordance with the eccentricity of the stiffener. As shown in the results of computations, the eccentricity effect of concentrated load case is greater than that of distributed load case and that of simply supported boundary condition is greater than that of clamped boundary condition. The higher eccentricity of stiffener is, the smaller the effect of stiffener becomes, therefore scantling of eccentrically stiffened plates should be considerably greater than those of symmetrically stiffened plates.

  • PDF

전자기 유한요소법 전자빔 시뮬레이션을 이용한 정전기장 제거용 연한 X-선관 설계 특성 연구 (Design of Soft X-ray Tube and Simulation of Electron Beam by Using an Electromagnetic Finite Element Method for Elimination of Static Electric Field)

  • 박태영;이상석;박래준
    • 한국자기학회지
    • /
    • 제24권2호
    • /
    • pp.66-69
    • /
    • 2014
  • 유한요소법으로 분할 표시한 연한 X-선 퍼짐관을 설계하였다. 연한 X-선관의 모양설계 및 구체적인 좌표를 설정하고 전자빔 궤적을 OPERA-3D SW 프로그램을 이용하여 시뮬레이션하였다. 음극과 양극인 텅스텐 필라멘트와 타겟에 인가한 전압, 온도, 열전자 일함수 등을 고정하였다. 필라멘트 십자형 모양을 구비한 퍼짐관의 구조에 따른 전자빔의 분포와 초점변화를 분석하여 반도체 공정상의 정전기장 제거용 연한 X-선 퍼짐관 설계를 최적화하였다.

조류 하중을 받는 탄성 현수선 케이블의 동적 해석 (Dynamic Analysis of Elastic Catenary Cable Subjected to Current)

  • 백인열;장승필;윤종윤
    • 한국지진공학회논문집
    • /
    • 제2권2호
    • /
    • pp.95-104
    • /
    • 1998
  • 수중 케이블의 동적 거동은 비선형 거동을 보이게 되는데 특히 기하하적 비선형성에 크게 영향을 받는다. 또한, 유체의 흐름으로 인하여 동적 거동의 해석은 더욱 복잡하고 어려워지기 때문에 해석적인 접근 방법에는 한계가 있다. 본 연구에서는 탄성 현수선 케이블요소에 동수력을 고려할 수 있게 하였다. 즉, 동수력을 받는 3차원 탄성 현수선 케이블를 정식화하고, 정적 및 동적 해석을 수행할 수 있는 유한요소 방법을 제시하였다. 동수력은 수정된 Morison 방정식을 이용하여 산정하였다. 제시된 방법으로 구한 수중케이블에 관한 동적 거동을 파악하려 하였으며, 정박 또는 예인에 사용하는 수중케이블의 경우 조류의 방향 및 케이블의 경사각에 따른 동적거동의 변화를 알아볼 수 있다.

  • PDF

CHARACTERIZATIONS OF PARTITION LATTICES

  • Yoon, Young-Jin
    • 대한수학회보
    • /
    • 제31권2호
    • /
    • pp.237-242
    • /
    • 1994
  • One of the most well-known geometric lattices is a partition lattice. Every upper interval of a partition lattice is a partition lattice. The whitney numbers of a partition lattices are the Stirling numbers, and the characteristic polynomial is a falling factorial. The set of partitions with a single non-trivial block containing a fixed element is a Boolean sublattice of modular elements, so the partition lattice is supersolvable in the sense of Stanley [6]. In this paper, we rephrase four results due to Heller[1] and Murty [4] in terms of matroids and give several characterizations of partition lattices. Our notation and terminology follow those in [8,9]. To clarify our terminology, let G, be a finte geometric lattice. If S is the set of points (or rank-one flats) in G, the lattice structure of G induces the structure of a (combinatorial) geometry, also denoted by G, on S. The size vertical bar G vertical bar of the geometry G is the number of points in G. Let T be subset of S. The deletion of T from G is the geometry on the point set S/T obtained by restricting G to the subset S/T. The contraction G/T of G by T is the geometry induced by the geometric lattice [cl(T), over ^1] on the set S' of all flats in G covering cl(T). (Here, cl(T) is the closure of T, and over ^ 1 is the maximum of the lattice G.) Thus, by definition, the contraction of a geometry is always a geometry. A geometry which can be obtained from G by deletions and contractions is called a minor of G.

  • PDF

지하매설 가스관의 검사를 위한 누설자속탐상 PIG 설계에 관한 연구 (Research on MFL PIG Design for the Inspection of Underground Gas Pipeline)

  • 박상호;박관수
    • 비파괴검사학회지
    • /
    • 제22권2호
    • /
    • pp.177-186
    • /
    • 2002
  • 본 논문에서는 3차원 형태의 결함을 가진 지하매설 가스관에서 누설자속(magnetic flux leakage, MFL) 탐상 법을 사용한 결함 검출에 관하여 연구하였다. 영구자석과 요크로 구성된 자기 시스템을 유한요소법을 사용하여 해석하고 동작점을 설정하였다. 가스관이 충분히 포화되지 않은 경우에는 측정이 곤란하며, 과대포화 된 경우에는 결함에 의한 누설자속의 변화량이 적어서 측정이 곤란하므로 적정한 값을 설정하여야 하므로 자기 시스템의 동작점은 결함이 있을 때 누설자속 증가율이 최대가 되도록 설정하여야 한다. 본 논문에서는 3차원 비선형 유한요소법을 사용하여, 가스관에 결함이 있는 경우 결합의 크기, 깊이에 따른 결함신호를 예측하여 그 결과 가스관 포화상태의 적절여부, 홀 센서 range 및 resolution의 적정도 등을 연구하였다. 또한 홀 센서의 민감도 형장을 위하여 back-yoke를 사용하여 측정신호를 향상시키는 방법을 제안하였다.

지하매설 가스관의 부식 및 결함 탐지를 위한 비파괴 누설 탐상시스템 개발에 관한 연구 (Research on MFL PIG Design for caustic and defect the Inspection of Underground Gas Pipeline)

  • 박상호;박관수
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2002년도 춘계합동학술대회 논문집
    • /
    • pp.11-20
    • /
    • 2002
  • 본 논문에서는 3차원 형태의 결함을 가진 지하매설 가스관에서 누설자속(magnetic flux leakage, MFL) 탐상법을 사용한 결함 검출에 관하여 연구하였다. 영구자석과 요크로 구성된 자기 시스템을 유한요소법을 사용하여 해석하고 동작점을 설정하였다. 가스관이 충분히 포화되지 않은 경우에는 측정이 곤란하며, 과대포화된 경우에는 결함에 의한 누설자속의 변화량이 적어서 측정이 곤란하므로 적정한 값을 설정하여야 하므로 자기 시스템의 동작점은 결합이 있을 때 누설자속 증가율이 최대가 되도록 설정하여야 한다. 본 논문에서는 3차원 비선형 유한요소법을 사용하여, 가스관에 결함이 있는 경우 결함의 크기, 깊이에 따른 결함신호를 예측하여 그 결과 가스관 포화상태의 적절여부, 홀 센서 range 및 resolution의 적정도 등을 연구하였다. 또한 홀 센서의 민감도 향상을 위하여 back-yoke를 사용하여 측정신호를 향상시키는 방법을 제안하였다.

  • PDF

수복물의 종류가 근관치료된 상악 제2소구치의 응력분포에 미치는 영향: 3차원 유한요소법적 연구 (EFFECT OF RESTORATION TYPE ON THE STRESS DISTRIBUTION OF ENDODONTICALLY TREATED MAXILLARY PREMOLARS; THREE-DIMENSIONAL FINITE ELEMENT STUDY)

  • 정현숙;김현철;허복;김광훈;손권;박정길
    • Restorative Dentistry and Endodontics
    • /
    • 제34권1호
    • /
    • pp.8-19
    • /
    • 2009
  • 본 연구의 목적은 다양한 교합하중 조건하에서 아말감, 복합레진, 세라믹 인레이, 그리고 금 인레이로 수복한 근관치료된 상악 제2소구치의 음력분포를 3차원 유한요소법으로 분석하는 것이다. 발치된 상악 제2소구치를 이용하여 근관치료된 3차원 유한요소모형을 제작하였다. 제작된 소구치 모형의 근관와동을 위 4가지 재료로 각각 수복한 후, 협측교두 (Load-1) 또는 설측교두 (Load-2)에 500 N의 하중을, 설측교두와 근심변연에 총 170 N의 하중 (Load-3)을 가하였다. 세 가지의 하중조건 하에서 각 수복물에 따른 협측과 설측의 치경부 그리고 교합면의 정중구에서 나타나는 인장응력의 분포양상을 ANSYS 프로그램으로 분석하여 다음과 같은 결과를 얻었다. 1. 모든 수복물의 경우에서 Load-1에서는 설측의 치경부, Load-2에서는 협측의 치경부에서 높은 응력이 관찰되었고 수복물 종류에 따른 차이는 관찰되지 않았다. 2. 모든 수복물의 경우에서 교합면의 하중점 근처 와정중구를 따라 높은 응력이 관찰되었고 수복물 종류에 따라 약간의 차이가 관찰되었다. 3. 모든 수복물의 경우에서 Load-3에서는 하중점 근처에서 높은 응력이 관찰되었고 수복물 종류에 따른 차이는 관찰되지 않았다.

원형 감육이 발생한 중수로 피더관의 한계하중 평가 (Limit Loads for Circular Wall-Thinned Feeder Pipes Subjected to Bending and Internal Pressure.)

  • 제진호;이국희;정하주;김종성;김윤재
    • 대한기계학회논문집A
    • /
    • 제34권11호
    • /
    • pp.1675-1680
    • /
    • 2010
  • 캐나다형 중수로에서 피더관은 가동 중에 유동 가속 부식에 의해 감육이 발생한다. 피더관에 감육이 발생하면 배관 건전성이 떨어진다. 본 논문은 원형 감육이 발생한 피더관에서의 기기신뢰성 평가를 위한 한계 하중을 연구하였다. 유한요소 해석을 통하여 면내 굽힘 하중과 내압을 받는 경우에 대하여 연구하였다. 재료는 대변형 효과를 고려하고 탄성-완전소성 재료로 가정하였다. 원형 감육이 발생한 피더관에 대하여 내압과 닫힘 방향, 열림 방향 굽힘 하중에 대하여 한계하중해를 제시하였다.