• Steel and Composite Structures
• /
• 제12권6호
• /
• pp.541-548
• /
• 2012

This paper deals with the applicability of extended layerwise optimization method (ELOM) for frequency optimization of laminated composite plates. The design objective is the maximization of the fundamental frequency of the laminated plates. The fibre orientations in the layers are considered as design variables. The first order shear deformation theory (FSDT) is used for the finite element solution of the laminates. Finally, the numerical analysis is carried out to show the applicability of extended layerwise optimization algorithm of laminated plates for different parameters such as plate aspect ratios and boundary conditions.

• Composites Research
• /
• 제24권4호
• /
• pp.29-35
• /
• 2011

전통적인 특성길이 방법을 이용하여 원공이 있는 복합재 적층판의 강도를 예측하기 위해서는 원공이 있는 적층뿐만 아니라 원공이 없는 적층판에 대한 시험 결과와 유한요소해석이 필요하였다. 본 논문에서는 응력집중계수와 재료상수를 이용하여 유한요소해석 없이 복합재 적층판 원공 주위의 응력분포 및 인장특성길이를 추정하고, 이를 바탕으로 원공이 있는 복합재 적층판의 인장강도를 예측할 수 있는 방법을 제안하였다. 또한 새로운 방법에서는 재료의 효과가 변수로 고려되므로 다양한 재료에 대한 적용이 가능하며 원공이 있는 복합재 적층판에 대한 시험도 생략할 수 있다. 적층판 주위의 응력분포는 유한요소해석과의 비교를 통해 검증하였고, 최종적으로는 USN125 탄소/에폭시 적층판을 제작하여 파손하중 예측 결과와 시험 결과를 비교하였다. 원공이 있는 다양한 형상의 복합재 적층판의 파손강도 예측 결과는 최대 8% 이내의 오차로 시험 결과와 잘 일치함을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제6권7호
• /
• pp.757-772
• /
• 1998

The objective of the present work is to estimate the strength and failure characteristics of symmetric thin square laminates under negative shear load. Two progressive failure analyses, one using the Hashin criterion and the other using a Tensor polynomial criterion, are used in conjunction with the finite element method. First-order shear-deformation theory along with geometric nonlinearity in the von Karman sense has been incorporated in the finite element modeling. Failure loads, associated maximum transverse displacements, locations and modes of failure including the onset of delamination are discussed in detail; these are found to be quite different from those for the positive sheer load reported in Part I of this study (Singh et al. 1998).

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.733-743
• /
• 2018

This paper presents post-buckling responses of a simply supported laminated composite beam subjected to a non-follower axially compression loads. In the nonlinear kinematic model of the laminated beam, total Lagrangian approach is used in conjunction with the Timoshenko beam theory. In the solution of the nonlinear problem, incremental displacement-based finite element method is used with Newton-Raphson iteration method. There is no restriction on the magnitudes of deflections and rotations in contradistinction to von-Karman strain displacement relations of the beam. The distinctive feature of this study is post-buckling analysis of Timoshenko Laminated beams full geometric non-linearity and by using finite element method. The effects of the fibber orientation angles and the stacking sequence of laminates on the post-buckling deflections, configurations and stresses of the composite laminated beam are illustrated and discussed in the numerical results. Numerical results show that the above-mentioned effects play a very important role on the post-buckling responses of the laminated composite beams.

• Coupled systems mechanics
• /
• 제7권6호
• /
• pp.691-705
• /
• 2018

In this paper, nonlinear displacements of laminated composite beams are investigated under non-uniform temperature rising with temperature dependent physical properties. Total Lagrangian approach is used in conjunction with the Timoshenko beam theory for nonlinear kinematic model. Material properties of the laminated composite beam are temperature dependent. In the solution of the nonlinear problem, incremental displacement-based finite element method is used with Newton-Raphson iteration method. The distinctive feature of this study is nonlinear thermal analysis of Timoshenko Laminated beams full geometric non-linearity and by using finite element method. In this study, the differences between temperature dependent and independent physical properties are investigated for laminated composite beams for nonlinear case. Effects of fiber orientation angles, the stacking sequence of laminates and temperature on the nonlinear displacements are examined and discussed in detail.

• Structural Engineering and Mechanics
• /
• 제66권1호
• /
• pp.27-36
• /
• 2018

The objective of this work is to analyze geometrically nonlinear static analysis a simply supported laminated composite beam subjected to a non-follower transversal point load at the midpoint of the beam. In the nonlinear model of the laminated beam, total Lagrangian finite element model of is used in conjunction with the Timoshenko beam theory. The considered non-linear problem is solved considering full geometric non-linearity by using incremental displacement-based finite element method in conjunction with Newton-Raphson iteration method. There is no restriction on the magnitudes of deflections and rotations in contradistinction to von-Karman strain displacement relations of the beam. In the numerical results, the effects of the fiber orientation angles and the stacking sequence of laminates on the nonlinear deflections and stresses of the composite laminated beam are examined and discussed. Convergence study is performed. Also, the difference between the geometrically linear and nonlinear analysis of laminated beam is investigated in detail.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.97-107
• /
• 1995

Global postbuckling analysis is accomplished for one-dimensional and two-dimensional delaminations. A new finite element model, which can be used to model the global postbuckling analysis of one-dimensional and two-dimensional delaminations, is presented. In order to calculate the strain energy release rate, geometrically nonlinear analysis is accomplished, and the incremental crack closure technique is introduced. To check the effectiveness of the finite element models and the incremental crack closure technique, the simplified closed-form sloution for a through-the-width delamination with plane strain condition is derived and compared with the finite element result. The finite element results show good agreement with the closed-foul1 solutions. The present method was extended to calculate the strain energy release rate for two-dimensional delamination. For a symmetric circular delamination, the strain energy release rate shows great variation along the delamination front. and the delamination growth appears to occur perpendicular to the loading direction.

• Steel and Composite Structures
• /
• 제11권2호
• /
• pp.115-130
• /
• 2011

Considering the randomness of material parameters in the laminated composite plate, a scheme of stochastic finite element method to analyze the displacement response variability is suggested. In the formulation we adopted the concept of the weighted integral where the random variable is defined as integration of stochastic field function multiplied by a deterministic function over a finite element. In general the elastic modulus of composite materials has distinct value along an individual axis. Accordingly, we need to assume 5 material parameters as random. The correlations between these random parameters are modeled by means of correlation functions, and the degree of correlation is defined in terms of correlation coefficients. For the verification of the proposed scheme, we employ an independent analysis of Monte Carlo simulation with which statistical results can be obtained. Comparison is made between the proposed scheme and Monte Carlo simulation.

• 오토저널
• /
• 제8권2호
• /
• pp.51-64
• /
• 1986

There has been considerable interest over the last twenty years in the subject of the elastic properties of the cord-rubber laminate. This has been due to the rather intensive study of the composites materials characteristics brought about by the increased use of rigid composites materials characteristics brought about by the increased use of rigid composites in many structural applications. The object of this study is to obtain the natural frequencies and modes of the simply supported cord-rubber laminate plates prior to the study on the analysis of the dynamic properties of the pneumatic tire. To obtain these natural frequencies and modes, the 12 degrees of freedom orthotropic rectangular plate finite elements are developed. By using classical lamination theory, the stress-strain relations are represented. The governing equation for the finite element is derived by energy method. To find the natural frequencies and modes, he eigenvalues and corresponding eigenvectors are computed by the well known Jacobi power method. In order to verify the capability of this present finite element, the results of the specially orthotropic plate and the angle-ply laminate plate are compared with the analytical solution. The analytical and numberical results are in good agreement. The following problems of the simply supported plate are analyzed by the present finite element. a) the natural frequencies and mode shapes of the cord-rubber laminate plate for various aspect ratio. b) The natural frequencies and mode shapes of the orthotropic plate with the rectangular hole in its center.

• Structural Engineering and Mechanics
• /
• 제6권6호
• /
• pp.633-641
• /
• 1998

Finite element solutions are presented for the optimal design of symmetrically laminated rectangular plates with various types of internal line supports. These plates are subject to a combination of simply supported, clamped and free boundary conditions. The design objective is the maximisation of the biaxial buckling load. This is achieved by determining the fibre orientations optimally with the effects of bending-twisting coupling taken into account. The finite element method coupled with an optimisation routine is employed in analysing and optimising the laminated plate designs. The effect of internal line support type and boundary conditions on the optimal ply angles and the buckling load are numerically studied. The laminate behavior with respect to fibre orientation changes significantly in the presence of internal line supports as compared to that of a laminate where there is no internal supporting. This change in behavior has significant implications for design optimisation as the optimal values of design variables with or without internal supporting differ substantially.