• 한국의류학회지
• /
• 제13권4호
• /
• pp.380-387
• /
• 1989

The Purpose of this study was to investigate the color changes of acid dyed wool fabrics after imparting permanent pleats with si-ro-set finish. Monoethanolamine sulfite was used as a reducing agent. Color changes were determined by measuring CIELAB values after treating the dyed fabrics with various setting temperatures, times and concentrations of MEAS. Setting temperature affected the color changes: in the order of $150^{\circ}C>130^{\circ}C>170^{\circ}C$ Setting time had a tendency to increase the color change. As the concentration of MEAS increased, $\delta$ E was increased. Azo dye was more affected than anthraquinone dye by MEAS treatment. Color changes were mainly due to $\delta$ L.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.17-22
• /
• 2002

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.206-208
• /
• 2006

The reliability of BGA (ball grid array) package with OSP (organic surface preservative) surface finish under thermal cycle was investigated by using SEM (scanning electron microscopy), EDS(energy dispersive spectroscopy), image tool and ball shear test. The IMCs (intermetallic compounds) were increased with increasing number of thermal cycles. However, the shear strengths of solder ball were decreased with increasing number of thermal cycles. The order of solders which had the highest shear strength as follow: Sn-3.5wt%Ag-0.7wt%Cu, Sn-0.7wt%Cu, Sn-37wt%Pb.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1597-1603
• /
• 1995

A prediction model on forward slip has been developed for presetting rolling speed of each finish mill stand in the continuous hot strip roduction. Those factors such as neutral point, friction coefficient, volume fractions undergoing width spread, shape of deformation zone at each side of entry and delivery of the rolls were taken into account. To reduce the speed unbalance between adjacent stands a refining method of adjusting friction coefficient has also been developed. On-line application of the model showed a good agreement in rolling speeds between the predictions and the actual measurements, and gave an outstanding improvement in the travelling stability of strip passing through the finishing mill train.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.814-820
• /
• 2000

This papers investigates the combined effects of parameters such as die surface finish, die directionality of stoning, contact pressure and draw speed on the resulting friction factor. Also, this study show the correlation between the NN(Neural Network) and DOE (Design of Experiments) to reduce the number of experiments without the loss of the effects of parameter upon friction factor. The experiments were run in random order with at least three replicates. It was found that the directional stoning orthogonal to the pulling direction is lower friction than directional stoning parallel to the pulling direction using FCD55 die and SPCEN

• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.38-43
• /
• 2006

A slot cut in end milling processes is one of the laborious works because the cutting force is likely to deflect the tools excessively, then to make large errors or to fracture the tool. This difficulty is owing to the poor stiffness of slender shaped end mills. Though, in most cases, additional finish cuts are followed after rough cuts, the accuracy of rough cuts is still important because it affects the final accuracy after finish cuts and productivity. The accuracy in slot cuts depends on the tool stiffness and the cutting conditions including depth of cut and feed. In order to meet the desired accuracy, diameter of end mill and cutting allowance have to be selected carefully. This study suggests several guidances for selecting the end mill diameter and the slot cut allowance to improve machining accuracy and productivity in slot end millings. Some experiments were done with the various cutting parameters of tool diameter, depth of cut and feed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 춘계 학술논문 발표대회
• /
• pp.209-210
• /
• 2012

In this study, the following conclusions are drawn. First, the Inorganic terazzo tile flooring and LCC (Life Cycle Cost) analysis showed that the sum of the total cost of 150,304 won Inorganic flooring, terrazzo tile flooring minerals won 186,202 to 35,898 won, compared to 8.22% analysis of the cost savings that have been appearing. Second, if the color chip has a unique and elegant sentence patterns, beautiful and high-strength bonding and that the crack resistance was investigated.

• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.423-430
• /
• 2011

Multi-input multi-output (MIMO) dynamic matrix control (DMC) technique is applied to control steam temperatures in a large-scale ultrasupercritical once-through boiler-turbine system. Specifically, four output variables (i.e., outlet temperatures of platen superheater, finish superheater, primary reheater, and finish reheater) are controlled using four input variables (i.e., two spray valves, bypass valve, and damper). The step-response matrix for the MIMO DMC is constructed using the four input and the four output variables. Online optimization is performed for the MIMO DMC using the model predictive control technique. The MIMO DMC controller is implemented in a full-scope power plant simulator with satisfactory performance.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.52-59
• /
• 1996

Conventionally, grinding of stainless steel, aluminium ally, copper alloy, and titanum alloy are difficult to obtain the high quality finish, because they have the mechanical properties such as low hardness, high toughness which result in the loading of wheel and the poor surface finish. Inorder to perform the grinding operations for these sorts of materials easily, the discontinuous grinding wheel with multi-porous grooves has newly been developed. The multi-porous grooves were formed during wheel production. This discontinous grinding wheel increases the grinding performance. It is desirable to use the discontinuous grinding wheel when grinding materials wiht high efficiency and accuracy which is impossible by conventional wheels. In this paper, the constructing and manufacturing method of grinding wheel with multi-proous grooves are explained, and the grinding charateristics of discontinuous grinding wheel are also illustrate.

• 대한기계학회논문집A
• /
• 제25권2호
• /
• pp.312-322
• /
• 2001

This paper investigates the combined effects of parameters such as die surface finish, die directionality of stoning contact pressure and draw speed on the resulting coefficient of friction. Also, this study show the correlation between the NN(Neural Network) and DOE(Design of Experiments) to reduce the number of experiments without the loss of the effects of parameter upon coefficient of friction. The experiments were run in random order with at least three replicates. It was found that the directional stoning orthogonal to the pulling direction is lower friction than directional stoning parallel to the pulling directi on using FCD55 die and SPCEN.