• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.317-322
• /
• 2001

This paper investigates the influence of fine aggregates on bleeding of concrete. According to test results, as water content decreases, crushed sand content increases, fluidity shows decline tendency. As for aggregates kinds, concrete using sea sand shows most fluidity loss among the tested results. Compressive strength gains highly when crushed sand is used. As for bleeding of concrete, bleeding shows decline tendency because of increasing in powder content and filling effect of voids. Bleeding amount is in a decreasing order of magnitude for concretes made with the following aggregates: sea sand, river sand, and crushed sand. Accordingly, crushed sand mixed with river sand and sea sand with certain proportion enable to reduce bleeding and enhance strength.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권3호
• /
• pp.178-185
• /
• 2011

본 연구는 강모래와 부순 모래를 일반적인 혼합방법과 아스팔트 골재 혼합에 사용되는 Driscoll 방법으로 각각 혼합하여 그 특성을 알아보고, Driscoll 방법의 콘크리트용 골재에 대한 적용성을 판단하고자 하였다. 이에 따라 일반혼합과 Driscoll 방법으로 혼합한 골재의 조립율 및 입도곡선, 굳지 않은 콘크리트의 특성 중 슬럼프와 공기량 및 굳은 콘크리트의 특성 중 28일 압축강도 시험을 통해 혼합방법의 따른 특성을 알아보고자 하였다. 아스팔트 골재의 혼합에 사용되는 Driscoll 방법을 사용하여 콘크리트 골재를 혼합하였을 때 일반적인 혼합방법과 비교하여 슬럼프, 공기량, 28일 압축강도가 오차수준 정도의 미미한의 차이를 나타내었다. 따라서 아스팔트 골재 혼합에 사용되는 Driscoll 방법은 콘크리트용 잔골재의 혼합에도 적용 가능할 것으로 판단된다.

• 한국지반공학회논문집
• /
• 제37권7호
• /
• pp.35-42
• /
• 2021

본 연구에서는 다양한 카올리나이트 혼합비에 따른 카올리나이트-모래 혼합토의 특성을 실험적으로 분석하였다. 이를 위하여 기본물성실험과 다짐시험을 실시하고 그 결과를 분석하였으며, 카올리나이트와 모래입자 간의 상호 구조를 더욱 자세히 분석하기 위하여 현미경 사진을 이용한 관측을 추가적으로 수행하였다. 실험결과, 카올리나이트 혼합비가 증가할수록 비표면적의 증가에 따른 함수비의 증가 및 모래입자와의 강한 결합구조를 형성하는 것으로 나타났으며, 최대 건조밀도는 감소하고 초기간극비는 증가하는 것으로 나타났다. 현미경 사진 분석 결과, 세립분 함량의 증가에 따라 모래의 특성이 지배적인 비율, 중간 비율, 세립분의 특성이 지배적인 비율을 확인할 수 있었으며, 세립분의 함량이 25-40% 정도인 경우에 입자간 상호작용이 잘 이루어지는 것을 관측할 수 있었다.

• 한국대기환경학회지
• /
• 제2권3호
• /
• pp.34-44
• /
• 1986

Particle size distribution of airborne suspended particulate concentrations according to particle size in the events of yellow sand phenomena, have been measured and analyzed by using Andersen air sampler for four years, January 1982 through December 1985. The conclusions are as follows: 1. Yellow sand phenomena, generally, occur between March and May. 2. The frequent occurrences of yellow sand were observed during March and April and airborne suspended particulate concentrations in the cases of yellow sand appeared to be 2 $\sim$ 3.4 times higher than those of normal conditions. 3. Geometric mean particle diameter and its geometric mean standard deviation by logarithmic normal distribution sheet, were quite close to each other and log-distribution curves showed similar shapes. 4. Analysis by particle size distribution curve showed bi-modal distribution. 5. Concentrations of coarse particles in normal conditions were 1.2 $\sim$ 2 times higher than those of fine particles and, similarly, coarse particle concentrations in yellow sand cases were 1.3 $\sim$ 2.5 times higher than those of fine particles. 6. Concentrations of coarse particles in yellow sand cases were 2 $\sim$ 3.6 times higher than those in normal conditions and those of fine particles were 1.7 $\sim$ 3.5 times higher.

• 청정기술
• /
• 제8권3호
• /
• pp.129-139
• /
• 2002

This is the study for recycling waste foundry sand. Authors studied about main subject of grading of aggregate and three experimental items such as physical properties of waste foundry sand, optimum grading for concrete products of low water ratio, and quality variations of concrete products according to substitution proportion of fine aggregate as waste foundry sand. We were convinced of following results by experimental study. The first was that waste foundry sand was not fit as the aggregate for concrete because of bad qualities such as grading, unit weight, solid volume and passing 0.08 mm seive, so it is proper to composition using with other fine aggregetes. The second was that optimum grading is fineness modulus of 2.77 to 3.28 And the last is that optimum condition about substitution proportion as waste foundry sand is 10% fine aggregate.

• 보존과학회지
• /
• 제38권4호
• /
• pp.334-346
• /
• 2022

The manufacturing technique was studied through the structure and material characteristics of the walls and the painting layers of the Avalokitesvara Bodhisattva mural of Geungnakjeon Hall, Daewonsa Temple. The mural is painted and connected to the earthen wall and the Junggit, and the wall is composed of wooden laths as a frame, the first and middle layers, the finishing layer, and the painting layer. The first layer, middle layer, and finishing layer constituting the wall were made by mixing weathered soil and sand. It was confirmed that the first layer had a high content of loess below silt, and the finishing layer had a high content of fine-sand and very fine sand. For the painting layer, a ground layer was prepared using soil-based mineral pigments, and lead white, white clay, atacamite, minium, and cinnabar (or vermilion) pigments were used on top of it. The Avalokitesvara Bodhisattva mural was confirmed to belong to a category similar to the soil-made buddhist mural paintings of Joseon Dynasty. However, it shows characteristics such as a high content of fine sand in the finishing layer and overlapping over other colors. Such material and structural characteristics can constitute important information for future mural conservation status diagnoses and conservation treatment plans.

• Advances in concrete construction
• /
• 제10권5호
• /
• pp.431-441
• /
• 2020

For the purpose of improving the properties of UHPC as well as the economic efficiency in production of the material, Availability of river sands as fine aggregate instead of micro silica sand were investigated. Four different sizes of river sands were considered. Using river sand instead of micro silica sand increased the flowability, and decreased the yield stress and plastic viscosity in rheological properties, and the effect was higher with larger particle size of river sand. It was demonstrated by analyses based on the packing density. In the results of compressive strength and elastic modulus, even though river sand was not as good as micro silica sand, it could provide high strength of over 170 MPa and elastic modulus greater than 40 GPa. The difference in compressive strength depending on the size of river sand was explained with the concept of maximum paste thickness based on the packing density of aggregate. The flexural performance with river sand also presented relatively lower resistance than micro silica sand, and the reduction was greater with larger particle size of river sand. The flexural performance was proven to be also influenced by the difference in the fiber orientation distribution due to the size of river sand.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.463-466
• /
• 2005

This study examined the effects of comparatively widely used fine aggregates in the domestic construction fields on the quality of concrete through the analysis of the effects of such fine aggregates on the physical properties of fresh concrete and strength of hardened concrete. Results revealed that crushed sand degrades the fluidity and air entraining of concrete compared to natural aggregates like sea sand and river sand. Especially, the use of crushed sand exhibiting low grain shape and grade was seen to have larger adverse effect on the physical properties of concrete.

• Geomechanics and Engineering
• /
• 제17권1호
• /
• pp.19-30
• /
• 2019

Recent research on the behavior of silty sand tends to advocate the use of equivalent skeleton void ratio to characterize the density state of this type of soil. This paper presents an investigation to explore the physical meaning of the equivalent skeleton void ratio by means of DEM simulations for assemblies of coarse and fine particles under biaxial shear. The simulations reveal that the distribution pattern of fine particles in the soil skeleton plays a crucial role in the overall macroscopic response: The contractive response observed at the macro scale is mainly caused by the movement of fine particles out of the force chains whereas the dilative response is mainly associated with the migration of fine particles into the force chains. In an assembly of coarse and fine particles, neither all of the fine particles nor all of the coarse ones participate in the force chains to carry the external loads, and therefore a more reasonable definition for equivalent skeleton void ratio is put forward in which a new parameter d is introduced to take into account the fraction of coarse particles absent from the force chains.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.623-628
• /
• 2001

The objective of this study is to find out the effect of Horizontal vibration on the compressive strength for 7 days and 28 days cured concrete specimens according to the kind of fine aggregates and the variation of vibration velocities, and times began to vibrate. Three kinds of fine aggregate(river sand, sea sand, crush sand), three types of vibration velocities(0.25, 0.5 0.1kine(cm/sec)), and four steps of times(0, 3, 6, 9 hours after concrete casting) were chosen as the experimental parameters in this study, the vibrations are applied for 30 minutes in each case. From this study, the variation with type of fine aggregate doesn't show tendency and the compressive strength decreases with increasing vibration velocity. When the vibration force time is more than 6 hour, It shows that compressive strength decreases under the condition of vibration velocity which the value is 0.5 kine and 1 kine, respectively.