• 한국분말재료학회지
• /
• 제26권4호
• /
• pp.311-318
• /
• 2019

The objective of this study is to investigate the influence of powder shape and densification mechanism on the microstructure and mechanical properties of Ti-6Al-4V components. BE powders are uniaxially and isostatically pressed, and PA ones are injection molded because of their high strengths. The isostatically compacted samples exhibit a density of 80%, which is higher than those of other samples, because hydrostatic compression can lead to higher strain hardening. Owing to the higher green density, the density of BE-CS (97%) is found to be as high as that of other samples (BE-DS (95%) and P-S (94%)). Furthermore, we have found that BE powders can be consolidated by sintering densification and chemical homogenization, whereas PA ones can be consolidated only by simple densification. After sintering, BE-CS and P-S are hot isostatically pressed and BE-DS is hot forged to remove residual pores in the sintered samples. Apparent microstructural evolution is not observed in BE-CSH and P-SH. Moreover, BE-DSF exhibits significantly fine grains and high density of low-angle grain boundaries. Thus, these microstructures provide Ti-6Al-4V components with enhanced mechanical properties (tensile strength of 1179 MPa).

• 한국분말재료학회지
• /
• 제29권1호
• /
• pp.28-33
• /
• 2022

Aluminum-based powders have attracted attention as key materials for 3D printing owing to their low density, high specific strength, high corrosion resistance, and formability. This study describes the effects of TiC addition on the microstructure of the A6013 alloy. The alloy powder was successfully prepared by gas atomization and further densified using an extrusion process. We have carried out energy dispersive X-ray spectrometry (EDS) and electron backscatter diffraction (EBSD) using scanning electron microscopy (SEM) in order to investigate the effect of TiC addition on the microstructure and texture evolution of the A6013 alloy. The atomized A6013-xTiC alloy powder is fine and spherical, with an initial powder size distribution of approximately 73 ㎛ which decreases to 12.5, 13.9, 10.8, and 10.0 ㎛ with increments in the amount of TiC.

• 한국분말재료학회지
• /
• 제30권1호
• /
• pp.7-12
• /
• 2023

Metal-additive manufacturing techniques, such as selective laser sintering (SLS), are increasingly utilized for new biomaterials, such as cobalt-chrome (Co-Cr). In this study, Co-Cr gas-atomized powders are used as charge materials for the SLS process. The aim is to understand the consolidation of Co-Cr alloy powder and characterization of samples sintered using SLS under various conditions. The results clearly suggest that besides the matrix phase, the second phase, which is attributed to pores and oxidation particles, is observed in the sintered specimens. The as-built samples exhibit completely different microstructural features compared with the casting or wrought products reported in the literature. The microstructure reveals melt pools, which represent the characteristics of the scanning direction, in particular, or of the SLS conditions, in general. It also exposes extremely fine grain sizes inside the melt pools, resulting in an enhancement in the hardness of the as-built products. Thus, the hardness values of the samples prepared by SLS under all parameter conditions used in this study are evidently higher than those of the casting products.

• 한국분말재료학회지
• /
• 제30권5호
• /
• pp.436-441
• /
• 2023

Molybdenum-tungsten (Mo-W) alloy sputtering targets are widely utilized in fields like electronics, nanotechnology, sensors, and as gate electrodes for TFT-LCDs, owing to their superior properties such as high-temperature stability, low thermal expansion coefficient, electrical conductivity, and corrosion resistance. To achieve optimal performance in application, these targets' purity, relative density, and grain size of these targets must becarefully controlled. We utilized nanopowders, prepared via the Pechini method, to obtain uniform and fine powders, then carried out spark plasma sintering (SPS) to densify these powders. Our studies revealed that the sintered compacts made from these nanopowders exhibited outstanding features, such as a high relative density of more than 99%, consistent grain size of 3.43 ㎛, and shape, absence of preferred orientation.

• 공업화학
• /
• 제9권7호
• /
• pp.1011-1017
• /
• 1998

$YBa_2Cu_3O_{6+x}(Y123)-Ag$ 초전도 선재를 0/20 wt%의 은(Ag)을 첨가한 발화합성분말과 고상반응분말을 사용하여 플라스틱 압출법으로 제조하였다. 플라스틱 압출법은 분말제조, 플라스틱 paste 제조, 다이 압축, binder 소각 및 소결공정을 포함한다. 양질의 초전도체를 제조하려면 원료물질이 균질하고 미세한 분말이어야 한다. 0/20 wt%를 첨가한 $Y_2O_3-BaCO_3-CuO$ precursor 분말을 발화합성(PS)법과 고상반응(MM)법으로 제조하였다. 원료분말이 Y123 초전도상으로 전이되는 생성속도를 공기중에서 여러온도와 시간별로 반응시켜 알아보았다. 발화합성법으로 제조한 분말이 고상반응법으로 제조한 분말보다 Y123상으로 빠르게 전이되었다. 이것은 PS법으로 제조한 분말이 미세한 크기와 균질한 화학적 조성으로 인해 Y123상으로 빠른 전이를 한 것이기 때문이다. 플라스틱 압출법으로 제조한 Y123-Ag 초전도 선재의 임계전류밀도($J_c$)는 원료분말의 특징에 따라 $150{\sim}230A/cm^2$값을 나타내었다. 은을 20 wt.% 첨가한 발화합성분말로 제조한 선재의 $J_c$는 $230A/cm^2$이었다.

• 한국결정성장학회지
• /
• 제18권6호
• /
• pp.248-252
• /
• 2008

전기전도성이 우수하면서 입자 크기가 작은 $LiFePO_4$ 분말을 얻기 위해서, 이종원소(Cr+B 또는 Cr+Al) 도핑이 $LiFePO_4$의 전기전도도에 미치는 영향과 열처리 조건이 입자 크기에 미치는 영향에 대해서 조사하였다. 조성이 $LiFe_{0.965}Cr_{0.03}B_{0.005}PO_4$ and $LiFe_{0.065}Cr_{0.03}Al_{0.005}PO_4$인 두 종류의 분말을 기계화학적 밀링법으로 혼합 후 $675{\sim}759^{\circ}C$에서 $5{\sim}10$시간 열처리하여 합성하였다. 이종원소 도핑은 입자성장을 촉진하였고 전기전도도를 높이는 효과가 있었다. $LiFe_{0.065}Cr_{0.03}Al_{0.005}PO_4$의 전기전도도는 $1{\times}10^{-8}S/cm$로 도핑하지 않은 것의 $5{\times}10^{-10}S/cm$보다 높았다.

• 한국분말재료학회지
• /
• 제10권1호
• /
• pp.26-33
• /
• 2003

Al-l4wt.%Ni-l4wt.% Mm(Mm=misch metal) alloy powders rapidly solidified by the gas atomization method were subjected to mechanical milling(MM). The morphology, microstructure and hardness of the powders were investigated as a function of milling time using scanning electron microscopy(SEM), transmission electron microscopy(TEM) and Vickers microhardness tester. Microstructural evolution in gas-atomized Al-l4wt.%Ni-l4wt.% Mm(Mm=misch metal) alloy powders was studied during mechanical milling. It was noted that the as-solidified particle size of $200\mutextrm{m}$ decreases during the first 48 hours and then increases up to 72 hours of milling due to cold bonding and subsequently there was continuous refinement to $20\mutextrm{m}$ on milling to 200 hours. Two microstructurally different zones, Zone A, which is fine microstructure area and Zone B, which has the structure of the as-solidified powder, were observed. The average thickness of the Zone A layer increased from about 10 to $15\mutextrm{m}$ in the powder milled for 24 hours. Increasing the milling time to 72 hours resulted in the formation of a thicker and more uniform Zone A layer, whose thickness increased to about $30~50\mutextrm{m}$. The TEM micrograph of ball milled powder for 200 hours shows formation of nano-particles, less than 20 nm in size, embedded in an Al matrix.

• 한국분말재료학회지
• /
• 제16권1호
• /
• pp.9-15
• /
• 2009

Amorphization and crystallization behaviors of $Ti_{50}Cu_{50}Ni_{20}Al_{10}$ powders during high-energy ball milling and subsequent heat treatment were studied. Full amorphization obtained after milling for 30 h was confirmed by X-ray diffraction and transmission electron microscope. The morphology of powders prepared using different milling times was observed by field-emission scanning electron microscope. The powders developed a fine, layered, homogeneous structure with prolonged milling. The crystallization behavior showed that the glass transition, $T_g$, onset crystallization, $T_x$, and super cooled liquid range ${\Delta}T=T_x-T_g$ were 691,771 and 80 K, respectively. The isothermal transformation kinetics was analyzed by the John-Mehn-Avrami equation. The Avrami exponent was close to 2.5, which corresponds to the transformation process with a diffusion-controlled type at nearly constant nucleation rate. The activation energy of crystallization for the alloy in the isothermal annealing process calculated using an Arrhenius plot was 345 kJ/mol.

• 한국분말재료학회지
• /
• 제12권4호
• /
• pp.273-278
• /
• 2005

Nanostructured TiN/$TiB_2$/$TiSi_2$ and TiN/$TiB_2$/$Ti_5Si_2$ composite powders have been prepared by mechanochemical reaction from mixtures of Ti, BN, and $Si_3N_4$ powders. The raw materials have reacted to form a uniform mixture of TiN, $TiB_2$ and $TiSi_2$ or $Ti_5Si_3$ depending on the amount of $Si_3N_4$ used in the starting mixtures, and the reaction proceeded through so-called mechanically activated self-sustaining reaction (MSR). Fine TiN and $TiB_2$ crystallites less than a few tens of nanometer were homogeneously dispersed in the amorphous $TiSi_2$ or $Ti_5Si_3$ matrix after milling for 12 hours. These amorphous matrices became crystalline phases after annealing at high temperatures as expected, but the original microstructure did not change significantly.

• Journal of Pharmaceutical Investigation
• /
• 제38권1호
• /
• pp.1-8
• /
• 2008

Planetary ball mill was used to decrease and control the particle size of excipients. The effects of the weight of sample and the revolution number of mill, and grinding time on the particle size of the ground sample were analyzed by response surface methodology. The optimum conditions for the milling of microcrystalline cellulose were 38.82 g of the weight of sample and 259 rpm of the revolution number of mill, and 45 minutes of grinding time. The predicted value of the particle size at the these conditions was $19.02{\mu}m$, of which the experimental value at the similar conditions was $18.68{\mu}m$. The tensile strength of tablets of single-component powders, such as microcrystalline cellulose, hydroxypropylmethyl cellulose and starch, binary mixtures and ground binary mixtures of these powder were measured at various relative densities. It was found that the logarithm of the tensile strength of the tablets was proportional to the relative density. A simple model, based upon Ryshkewitch-Duckworth equation that was originally proposed for porous materials, has been developed in order to predict the relationship between the tensile strength and relative density of ground binary tablets based on the properties of the constituent single-component powders. The validity of the model has been verified with experimental results for ground binary mixtures. It has demonstrated that this model can well predict the tensile strength of ground binary mixtures based upon the properties of single-component powders, such as true density, and the compositions. When the tensile strength of the mixture of microcrystalline cellulose hydroxypropylmethyl cellulose (90:10) and the ground mixture of them were compared, the tensile strength of the ground mixture decreased widely from 45.3 to 5.6% compared to the mixture in case the relative density of tablets was in the range of $0.7{\sim}0.9$. When the tensile strength of the mixture of microcrystalline cellulose starch (80:20) and the ground mixture of them were compared, the tensile strength of the ground mixture decreased widely from 31.0 to 11.6% compared to the mixture in case the relative density of tablets was in the range of $0.7{\sim}0.9$.