• Geomechanics and Engineering
• /
• v.31 no.6
• /
• pp.557-571
• /
• 2022

Landslides are often triggered by weak interlayers initiated in tailings dam foundations, and hazards gradually occur. This is serious for landslides in high tailings dams due to their high potential energy. Tailing samples with a fine-grained interlayer at a set dip angle were prepared. Consolidated undrained (CU) triaxial shear tests were carried out by using a high-pressure triaxial apparatus. The results were compared with the results under a low confining pressure. Four reasons were summarized for high tailings dams more prone to instability than low dams. The shear strength of the samples with dipping interlayers decreases with increasing dip angle. An obvious straight drop in the stress path after the peak occurs in samples with dipping interlayers at an angle of 60°. The effect of the interlayer on the mechanical behaviour of tailings is very sensitive, especially for the sample with a dipping interlayer at an angle of 60°. Shear slipping along the interlayer should be given more attention in tailings dams. Compared with the results under low confining pressure, the stress decreases continuously for the samples with dipping interlayers at large angles under high confining pressure. The positive pore pressure, which reduces the effective stress, occurred in tailings samples under high confining pressure. The residual strength of tailings under high confining pressure is smaller than that under low confining pressure. These factors increase the dam break risk and the disaster impact for high tailings dams.

• Korean Journal of Cognitive Science
• /
• v.21 no.1
• /
• pp.95-126
• /
• 2010

This study proposes a bottom-up and inductive manual mapping methodology for integrating two heterogenous fine-grained ontologies which were built by a top-down and deductive methodology, namely the Sejong semantic classes (SJSC) and the upper nodes in KorLexNoun 1.5 (KLN), for HLP applications. It also discusses various problematics in the mapping processes of two language resources caused by their heterogeneity and proposes the solutions. The mapping methodology of heterogeneous fine-grained ontologies uses terminal nodes of SJSC and Least Upper Bounds (LUB) of KLN as basic mapping units. Mapping procedures are as follows: first, the mapping candidate groups are decided by the lexfollocorrelation between the synsets of KLN and the noun senses of Sejong Noun Dfotionaeci(SJND) which are classified according to SJSC. Secondly, the meanings of the candidate groups are precisely disambiguated by linguistic information provided by the two ontologies, i.e. the hierarchicllostructures, the definitions, and the exae les. Thirdly, the level of LUB is determined by applying the appropriate predicates and definitions of SJSC to the upper-lower and sister nodes of the candidate LUB. Fourthly, the mapping possibility ic inthe terminal node of SJSC is judged by che aring hierarchicllorelations of the two ontologies. Finally, the ituorrect synsets of KLN and terminologiollocandidate groups are excluded in the mapping. This study positively uses various language information described in each ontology for establishing the mapping criteria, and it is indeed the advantage of the fine-grained manual mapping. The result using the proposed methodology shows that 6,487 LUBs are mapped with 474 terminal and non-terminal nodes of SJSC, excluding the multiple mapped nodes, and that 88,255 nodes of KLN are mapped including all lower-level nodes of the mapped LUBs. The total mapping coverage is 97.91% of KLN synsets. This result can be applied in many elaborate syntactic and semantic analyses for Korean language processing.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.4
• /
• pp.83-91
• /
• 2008

The development of the equal channel angular pressing(ECAP) process in metals has recently provided a feasible solution to produce ultra-fine or nano-grained bulk materials with tailored material properties. However, ECAP process is difficult to scale up commercially due to requirements of an excessive load. In this paper, a new Hybrid-ECAP process with torsional die is considered to obtain materials of ultra-fine grain structure under low forming load. An upper bound analysis and numerical simulation (DEFORM 3D, a commercial FEM code) are carried out on the torsional die. By the upper bound analysis, analytical expression for the compression force and rotation speed are obtained. By the FEM analysis, the distribution of strain, stress and deformation are obtained. These results show that the Hybrid-ECAP is a useful process because this process can obtain the homogeneous deformations with relatively low forming load. Additionally, due to decreased forming load, die life can be improve.

• Korean Journal of Metals and Materials
• /
• v.47 no.7
• /
• pp.397-405
• /
• 2009

The high strain rate deformation behavior of ultra-fine grained 5083 aluminum alloys prepared via equal channel angular (ECA) extrusion was investigated in this study. The microstructure of ECA extruded specimens consisted of ultra-fine grains, and contained a considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. According to the dynamic torsion test results, the maximum shear stress and fracture shear strain of the route A (no rotation) specimen were lower than those of route C ($180^{\circ}$ rotation) specimen since that adiabatic shear bands of $100{\mu}m$ in width were formed in the route A specimen. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity associated with ECA operations.

• Nuclear Engineering and Technology
• /
• v.54 no.7
• /
• pp.2359-2366
• /
• 2022

Selecting graphite grades with superior irradiation characteristics is important task for designers of graphite moderation reactors. To provide reference information and data for graphite selection, the effects of irradiation on three fine-grained, iso-molded nuclear grade graphites, ETU-10, IG-110, and NBG-25, were compared based on irradiation-induced changes in volume, thermal conductivity, dynamic Young's modulus, and coefficient of thermal expansion. Data employed in this study were obtained from reported irradiation test results in the high flux isotope reactor (HFIR)(ORNL) (ETU-10, IG-110) and high flux reactor (HFR)(NRL) (IG-110, NBG-25). Comparisons were made based on the irradiation dose and irradiation temperature. Overall, the three grades showed similar irradiation-induced property change behaviors, which followed the historic data. More or less grade-sensitive behaviors were observed for the changes in volume and thermal conductivity, and, in contrast, grade-insensitive behaviors were observed for dynamic Young's modulus and coefficient of thermal expansion changes. The ETU-10 of the smallest grain size appeared to show a relatively smaller VC to IG-110 and NBG-25. Drastic decrease in the difference in thermal conductivity was observed for ETU-10 and IG-110 after irradiation. The similar irradiation-induced properties changing behaviors observed in this study especially in the DYM and CTE may be attributed to the assumed similar microstructures that evolved from the similar size coke particles and the same forming method.

• Economic and Environmental Geology
• /
• v.19 no.spc
• /
• pp.175-191
• /
• 1986

The Geodo granodiorite intruded into the Joseon Supergroup is fine-grained at the marginal part, and medium-grained and more leucocratic at the central part. The Quartz monzonite porphyry intruded inte Precambrian granite and Geodo granodiorite has abundant plagioclase phenocryst. The Imog granite intruded into the Yulri Group and the Joseon Supergroup is mediumgrained biotite granite with partly pinkish feldspar phenocryst. The K/Ar ages obtained from the biotite of the Geodo granodiorite and Imog granite are Early ($111{\pm}1{\sim}107{\pm}1$ Ma) and Late ($93{\pm}1{\sim}92{\pm}1$ Ma) Cretaceous, respectively. The K/Ar sericite age of the quartz-sericite zone of the lower Jangsan quartzite occuring in the western area gave much younger age (about 170 Ma) than that of the Jangsan quartzite, that might be reset due to the regional metamorphism of the Daebo orogeny. The granitic rocks of the area are felsic to mafic, metaluminous to peraluminous, calc-alkalic (alkali-lime index${\fallingdotseq}$ 57) and I-type (magnetite-series) based on the chemical data_ And they appear to have been fractionated at the order of Geodo granodiorite, Quartz monzonite porphyry and Imog granite. In terms of mineralogy, geochemistry and K/Ar biotite age, a rock suite of monzodiorite, quartz monzodiorite and quartz monzonite-granodiorite in the Geodo stock was fractionally differentiated from a magmatic body from its margin to inward.

• The Journal of Engineering Geology
• /
• v.11 no.1
• /
• pp.51-62
• /
• 2001

Jurassic granites of three sites, Pocheon, Geochang and Habcheon, were analysed with respect to the characteristics of the rock cleavage. Microscopic analysis for the oriented thin sections of the specimens was conducted by using the scanline survey technique to measure microcrack direction, spacing and length. The results showed that the preferred orientations of microcrack developed in quartz and feldspar arc coincident with the orientation of quarry planes. The length of microcrack is related to grain size. The length of microcrack in coarse-grained granite is longer than that in relatively fine-grained granite. In all granites, microcracks related to the preferred orientations are well developed in order of rift, grain and hardway planes in number, length and density.

• Journal of Welding and Joining
• /
• v.25 no.1
• /
• pp.57-62
• /
• 2007

In the coarse grained HAZ of conventional TiN steel, most TiN particles are dissolved and austenite grain growth easily occurrs during high heat input welding. To avoid this difficulty, thermal stability of TiN particles is improved by increasing nitrogen content in EH36-TM steel. Increased thermal stability of TiN particle is helpful for preventing austenite grain growth by the pinning effect. In this study, the mechanical properties and microstructures of high heat input welded Tandem EGW joint in EH36-TM steel with high nitrogen content were investigated. The austenite grain size in simulated HAZ of the steel at $1400^{\circ}C$ was much smaller than that of conventional TiN steel. Even for high heat input welding, the microstructure of coarse grained HAZ consisted of fine ferrite and pearlite and the mechanical properties of the joint were sufficient to meet all the requirements specified in classification rule.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.468-474
• /
• 2015

Evaluations of the microstructure and mechanical properties of age hardenable Cu-2.0wt%Be alloy are performed in order to determine whether it can be used as a welding electrode for projection welding. The microstructure examinations, hardness measurements, and tensile tests of selective aging conditions are conducted. The results indicate that the aging treatment with the fine-grained microstructure exhibits better hardness and high tensile properties than those of the coarse-grained microstructure. The highest hardness value and high tensile strength are obtained from the aged condition of $300^{\circ}C$ for 360 min due to the presence of the metastable ${\dot{\gamma}}$ precipitates on the grain boundaries. The values of the highest hardness and tensile strength are measured as 374 Hv and 1236.2 MPa, respectively. The metastable ${\dot{\gamma}}$ precipitates are transferred to the equilibrium ${\gamma}$ precipitates due to the over-aged treatment. The presence of the ${\gamma}$ precipitates appears as nodule-like precipitates decorated around the grain boundaries. The welding electrode with the best aging treated condition exhibits better welding performance for electrodes than those of electrodes used previously.

• Journal of the Korean Ceramic Society
• /
• v.33 no.5
• /
• pp.602-615
• /
• 1996

The purpose of the present study is to investigate the microstructural effect on the R-curve behavior in three aluminas with different grain size distributions by analyzing the bridging stress distribution. The crack opening displacement (COD) according to the distance behind the stationary crack tip was measured using an in situ SEM fracture method. The measured COD values in the fine-grained alumina agreed well with Wiederhorn's sollution while they deviated from Wiederhorn's solution in the two coarse-grained aluminas because of the increase of the crack closure due to the grain interface bridging in the crack wake. A numerical fitting procedure was conducted by the introduction of the power-law relation and the current theoretical model together with the measured COD's in order to obtain the bridging stress distribution. The results indicated that the bridging stress function and the R-curve computed by the current model were consistent with those computed by the power-law relation providing a reliable evidence for the bridging stress analysis of the current model. The strain-softening exponent in the power-law relation n, was calculated to be in the range from 2 to 3 and was closely related to the grain size distribution. Thus it was concluded from the current theoretical model that the grain size distribution affected greatly the bridging stress distribution thereby resulting in the quantitative analysis of microfracture of polycrystalline aluminas through correlating the local-fracture-cont-rolling microstructure.