• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.6
• /
• pp.59-67
• /
• 2006

Particles of soil are crushed when soil is compacted in the in-situ or lab. Among many factors that affect the crush of particles, compaction energy is a major factor. Because the crush of particles can change physical properties, the analysis of effect of compaction energy is very important. In this study, the fragmentation fractals were used for determining the change in grain size distribution and the effect due to change in grain size distribution was estimated. Compaction energy was increased by 50, 100, 200 and 300% based on the energy of standard A compaction test. As a result, grain size distribution curves were changed and fine particles increased as compaction energy were increased. Relative compaction were ranged between $93.38{\sim}107.67$. Fractal dimension of each site increased as compaction energy increased. Relative compaction is proportional to the fractal dimension but coefficients of permeability were in inverse proportional to the involution of fractal dimension.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.3
• /
• pp.46-59
• /
• 1980

This study was conducted to obtain the most effective distribution of grain size and the optimum lime content for lime-soil stabilization. To achieve the aim, the change of consistency, the characteristics of compaction and unconfined compressive strength were tested by adding of 0, 4, 6, 8, 10 and 12 percent lime by weight for all soils adjusted by given ratios of sand to clay. The results obtained were as follows; 1. There was a tendency that the plasticity index of lime-soil mixture was decreased by increasing the amount of lime, whereas the liquid limit was varied irregularly and the plastic limit was increased. 2. With the addition of more lime, the optimum moisture content of lime-soil mixture was increased, and the maximum dry density was decreased. 3. The optimum lime content of lime-soil mixture was varied from soil to soil, and the less amount of small grain size, the less value of optimum lime content. 4. The optimum distribution of grain size for lime-soil mixture was in the soil, having the ratio of about 60 percent of cohesive clay and about 40 percent of sand by weight. 5. In the soil having fine grain size, the effect of curing appeared for long periods of time, whereas the increasing rate of unconfined compressive strength was great on the soil of coarse grain size in the earlier stage of curing period.

• Journal of Powder Materials
• /
• v.17 no.3
• /
• pp.235-241
• /
• 2010

Mo nanopowder was synthesized by ball-milling and subsequent hydrogen-reduction of $MoO_3$ powder. To fabricate ultra fine grained molybdenum, two-step sintering and spark plasma sintering process were employed. The grain size of specimen by two-step sintering and spark plasma sintering was around $0.6\;{\mu}m$ and $0.4\;{\mu}m$, respectively. Mechanical properties of ultra fine grained Mo with relative density of above 90% were significantly improved at room and high temperatures comparing to commercial bulk Mo of 99% relative density. This result was mainly explained by the grain size refinement due to diffusion-controlled sintering.

• Journal of The Geomorphological Association of Korea
• /
• v.26 no.1
• /
• pp.27-40
• /
• 2019

This study tries to reveal source areas of fluvial terrace deposits in Danyang and Geum River basins located in the northern and southern parts of the Sobaek Mountains, respectively, through geochemistry. The samples analyzed in this study show different grain size properties and can be grouped into the coarse, medium and fine samples. Grain size properties suggest that the coarse samples are typically fluvial deposits and geochemistry from the coarse samples is also similar to that from the bedrocks within the basins. The fine samples show geochemical properties different from the bedrocks and similar to loess deposits in Korea. However, different geochemical concentrations among the fine samples can be also recognized, indicating mixtures of loess materials with weathering products of the bedrocks. One sample among the medium samples is considered as fluvial deposit due to geochemical similarity to the bedrocks, while geochemistry from another sample among the medium samples indicates that loess materials were mixed with more abundant weathering products of the bedrocks than those in the fine samples.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.375-375
• /
• 2007

In the conventional crystallization method, thepoly-Si TFTs show poor device-to-device uniformity because of the random location of the grain boundaries. However, our new crystallization method introduced in this paper employed substrate-embedded seeds on the highly ordered anodic alumina template to control both the location of seeds and the number of grain boundaries intentionally. In the process of excimer laser crystallization (ELC), a-Si film deposited on the anodic alumina by low pressure chemical vapor deposition (LPCVD) is transformed into fine poly-Si grains by explosive crystallization (XC) prior to primary melting. At the higher energy density, the film is nearly completely melted and laterally grown by super lateral growth (SLG) from remained small part of the fine poly-Si grains as seeds at the Si/anodic alumina interface. Resultant grain boundaries have almost linear functions of the number of seeds in concavities of anodic alumina which have a constant spacing. It reveals the uniformity of. device can be enhanced prominently by controlling location and size of pores which contains fine poly~Si seeds under artificial anodizing condition.

• Journal of the Korean Ceramic Society
• /
• v.33 no.5
• /
• pp.602-615
• /
• 1996

The purpose of the present study is to investigate the microstructural effect on the R-curve behavior in three aluminas with different grain size distributions by analyzing the bridging stress distribution. The crack opening displacement (COD) according to the distance behind the stationary crack tip was measured using an in situ SEM fracture method. The measured COD values in the fine-grained alumina agreed well with Wiederhorn's sollution while they deviated from Wiederhorn's solution in the two coarse-grained aluminas because of the increase of the crack closure due to the grain interface bridging in the crack wake. A numerical fitting procedure was conducted by the introduction of the power-law relation and the current theoretical model together with the measured COD's in order to obtain the bridging stress distribution. The results indicated that the bridging stress function and the R-curve computed by the current model were consistent with those computed by the power-law relation providing a reliable evidence for the bridging stress analysis of the current model. The strain-softening exponent in the power-law relation n, was calculated to be in the range from 2 to 3 and was closely related to the grain size distribution. Thus it was concluded from the current theoretical model that the grain size distribution affected greatly the bridging stress distribution thereby resulting in the quantitative analysis of microfracture of polycrystalline aluminas through correlating the local-fracture-cont-rolling microstructure.

• Journal of Magnetics
• /
• v.9 no.4
• /
• pp.109-112
• /
• 2004

The HDDR (Hydrogenation-Disproportionation-Desorption-Recombination) process is a special method to produce anisotropic NdFeB powders for bonded magnet. The effect of the modified HDDR process on magnetic properties of $Nd_2Fe_{14}B$-based magnet with several composition $Nd_{11.2}Fe_{66.5-x}Co_{15.4}B_{6,8}Zr{0.1}Ga_x(x=0{\sim}1.0)$ and that of microelement Ga, disproportional temperature and annealing temperature on $_jH_c$, grain size were investigated in order to produce anisotropic powder with high magnetic properties. It was found that modified HDDR process is very effective to enhance magnetic properties and to fine grain size. The addition of Ga could change disproportionation character remarkably of the alloy and could improve magnetic properties of magnet powder. Increasing annealing temperature induces significant grain growth. And grain size produced by modified HDDR process is significantly smaller than those produced by conventional HDDR process.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.217-221
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occupied during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of high nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400 C and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.6
• /
• pp.315-322
• /
• 2010

Effect of hardenability, grain size and microstructural change according to the change of austenitizing temperature was analyzed in Jominy hardenability test of AISI 51B20 steel. Grain growth was small, 7 ${\mu}m$ and 12 ${\mu}m$ austenite grain sizes at austenitizing temperature of $900^{\circ}C$ and $1000^{\circ}C$, respectively, while rapid grain growth was observed up to 30 ${\mu}m$ austenite grain size at austenitizing temperature of $1100^{\circ}C$. As austenitizing temperature increased from $900^{\circ}C$ to $1100^{\circ}C$, hardenability in the region within 15 mm from end-quenched surface decreased due to the grains growth of bainite and martensite mixture, on the other hand the hardenability in the region exceeding 15 mm from end-quenched surface increased. Increased hardenability was attributed to different microstructures; pearlite, fine pearlite and bainite, and bainite and martensite structures at austenitizing temperature of $900^{\circ}C$, $1000^{\circ}C$ and $1100^{\circ}C$, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.163-171
• /
• 1999

The abnormal grain coarsening in wire rolling induces detrimental defects, such as jagged size tolorance, severe bending after heat treatments and drawing troubles, in the following secondary processes. Neishi et al observed that there is a band type region where grain coarsenting occurs in the plastic strain vs. deformation temperature plot. Based on the finding, we have investigate whether grain sizes and ferrite volume fractions are correlation to deformation strain with three kinds of wire rod diameters as for the different average deformation conditions. The samples were chosen from the No.2 Wire Rod Mill of POSCO where 3-roll type of finishing mill stand are used. It was found in the present work that the grain size and ferrite volume fraction of the rolled and cooled microstructure were changed with rolling reduction and rolling temperature. Abnormally grown grains at various observed points were also found. To have homogeneously fine grains of microstructure from the No. 2 Wire Rod Mill, it will be easier to control finish rolling temperature at around 750$^{\circ}C$ rather than to find another rolling schedule.