• Journal of the Korean Wood Science and Technology
• /
• 제16권4호
• /
• pp.10-39
• /
• 1988

This study investigated the temperatures and relative humidities in the semi-greenhouse type solar dryer with a black rock-bed heat storage and without heat storage and outdoor temperature and relative humidity at 9 a.m. and 2 p.m.. A comparison was made of the drying rates, final moisture contents, moisture content distributions, casehardening stresses, drying defects, volumetric shrinkage of dried lumber for solar- and air-drying from the green condition of mixtures of Douglas-fir, lauan, taun, oak and sycamore 25mm- and 50 mm-thick lumber during the same period for four seasons, and heat efficiencies for solar dryer with and without the heat storage for saving of heat energy and the cost of lumber drying using the solar energy. The results from this study were summarized as follows: I. The mean weekly temperatures in the solar dryers were 3 to $6^{\circ}C$ at 9 a.m. and 9 to $13^{\circ}C$ at 2 p.m. higher than mean outdoor temperature during all the drying period. 2. The mean weekly relative humidities in the solar dryers were about 1 to 19% at 9 a.m. higher than the outdoor relative humidity. and the difference between indoor and outdoor relative humidity in the morning was greater than in the afternoon. 3. The temperatures and relative humidities in the solar dryer with and without the heat storage were nearly same. 4. The overall solar insolation during the spring months was highest and then was greater in the order of summer, atumm, and winter month. S. The initial rate of solar drying was more rapid than that of air drying. As moisture content decreased, solar drying rate became more rapid than that of air drying. The rates of solar drying with and without heat storage were nearly same. The drying rate of Douglas-fir was fastest and then faster in the order of sycamore, lauan, taun and oak. and the faster drying rate of species, the smaller differences of drying rates between thicknesses of lumber. The drying rates were fastest in the summer and slowest in the winter. The rates of solar drying during the spring were more slowly in the early stage and faster in the later stage than those during the autumn. 6. The final moisture contents were above 15% for 25mm-thick air dried and about 10% for solar dried lumber, but the mean final MCs for 50mm-thick lumber were much higher than those of thin lumber. The differences of final MC between upper and lower course of pile for solar drying were greater than those of pile for air drying. The differences of moisture content between the shell and the core of air dried lumbers were greater than those of solar dried lumber, smallest in the drying during summer and greatest in the drying during winter among seasons. 7. Casehardening stresses of 25mm- and 50mm-thick dried lumber were slight, casehardening stress of solar dried lumber was severer than that of air dried lumber and was similar between solar dried lumber with and without heat storage, Casehardening stresses of lumber dried during spring were slightest and then slighter in the order of summer, autumn, and winter. Casehardening stresses of Douglas -fir, sycamore and lauan were slight, comparing with those of taun and oak. 8. Maximum initial checks of 25mm-thick lumber occurred above and below fiber saturation point and those of 50mm-thick lumber occurred in the higher moisture content than thin lumber. As the moisture content decreased, most of checks were closed and didn't show distinct difference of the degree of checks among drying methods. The degree of checks were very slight in case of Douglas-fir and lauan, and severe in case of taun and oak. The degree of checks for 50mm-thick lumber were severer than those for 25mm-thick lumber. 9. The degree of warpage showed severe in case of oak and sycamore lumber, but no warping was found in case of Douglas-fir, lauan and taun. 10. The volumetric shrinkages of taun and oak were large and medium in case of Douglas-fir, lauan and sycamore. 11. Heat efficiencies of solar dryer with heat storage were 6.9% during spring, 7.7% during summer, 12.1% during autumn and 4.1% during winter season. Heat efficiency of solar dryer with heat storage was slightly greater than that of without heat storage. As moisture content of lumber decreased, heat efficiency decreased.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.863-877
• /
• 1996

A drying model to predict the drying process in continuous dryer was developed and proved by drying experiments. The experiment showed that the difference of moisture contents between the predicted and the observed was within 0.5%(wb). There was no cracked rice found even in high drying rate with the inlet moisture content over 23%(wb), and tempering treatment in the same temperature reduced the ratio of cracked rice. There was a little difference in the ratio of cracked rice between 40$^{\circ}C$ and 45$^{\circ}C$ drying temperatures with the final drying moisture content (14.5% wb), and the cracked rice increased at 55$^{\circ}C$. As a results, it was better to make fast drying on the rice over 23%(wb) inlet content it was recommended to keep drying at 45$^{\circ}C$.

• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.89-96
• /
• 1984

This study was intended to search the thermal properties of rice which are necessary in preventing qualitative and quantitative losses in the drying and milling processes. First, the coefficient of cubical thermal expansion of brown rice was measured, which is required for analyzing the internal stress of rice, and then theoretical thermal and moisture stresses were calculated. The results are summarized as follows: 1. The coefficient of cubical thermal expansion of brown rice was about $2.81{\times}10^{-4}/^{\circ}C$ in the temperature range of $10^{\circ}C-60^{\circ}C$. 2. When the shape of brown rice was assumed to be a sphere or a cylinder, maximum thermal stress due to temperature change of $20^{\circ}C-60^{\circ}C$ was in the range of $25-100kg/cm^2$. And maximum moisture stress was in the range of $450-650kg/cm^2$ when the drying temperature was $35^{\circ}C$, initial and final moisture contents of brown rice were 20% and 14% (w.b.), and the moisture diffusion coefficient was assumed to be $6.79{\times}10^{-4}cm^2/hr$. 3. Consequently, it was concluded that crack formation in a rice kernel is mainly caused by moisture stress.

• Journal of Biosystems Engineering
• /
• 제23권3호
• /
• pp.229-244
• /
• 1998

This study was performed to determine proper fan and heater management schemes for natural air drying of rough rice in round steel bin with stirring device under Korean weather conditions. A computer simulation model was developed to predict moisture content changes, energy requirements, and drymatter losses during drying of rough rice by natural air. Drying test was conducted to validate the simulation model using round steel bin of holding capacity of 300ton at Rice Processing Complex in Jincheon. The bin was filled with rough rice every day and mixing by stirring device. Moisture contents, ambient air temperatures, relative humidities, static pressures in plenum chamber in the bin, airflow rates, and electrical and fuel energy were measured. Relative errors of moisture content changes predicted by the simulation model were below 5ft, and relative errors of final moisture content, final grain weight, required energy ranged from 0.9% to 6%. These not levels indicated that the simulation model can satisfactorily predict the performance factors of natural air drying system such as drying rates and energr consumptions comparing error level of 10% to 15% in other drying simulation models generally used in dryer desists. Twelve different fan and heater management schemes were evaluated using the computer simulation model based on three hourly weather data from Suweon for the period of 1952-1994. The best management schemes were selected comparing the drymatter losses, required drying times, required energy consumptions. Operating fan without heating only when ambient relative humidity was below 85% or 90% appeared to be the most effective method of In operation in favorable drying weather. Under adverse drying climates or to reduce required drying time, operating fan continuously, and heating air with $1.5^{\circ}C$ temperature rise only when ambient relative humidity was over 85% appeared to be the most suitable method.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 1997년도 총회 및 춘계 학술발표회 논문집
• /
• pp.47-52
• /
• 1997

The experimental investigations considered in this paper are similar in many respects to those of Lee$^1$, with some key differences. First, there is no layering of the soils in a heterogeneous liner. The only soil investigated is the clay component of the cover liner. This ensures that the clay is exposed to freezing and that frost propagation in the clay can be investigated separate from other processes. Second, a closed system approach to the simulation was adopted. According to Jones$^2$, closed-system freezing occurs when there is no source of water available beyond that originally present in the soil voids. Freezing under such conditions results in very thin or non-existent ice lenses. One of tile objectives of the experiments described in this paper was the moisture migration and the changing of moisture contents of the compacted clay liner in landfill. The closed-system was used to limit tile variables in the experimental simulation to make these calculations more direct, although the final results could be applied to an open system also. As a result, the moisture content decreased about 45%-46% after two freeze/thaw cycles.

• 한국환경보건학회지
• /
• 제22권4호
• /
• pp.82-90
• /
• 1996

This study was performed to find the optimum mixing ratio of paper waste in composting of mixture of swine feces and newspaper. Using the experimental setting of aeration rate which was found in the experiment carried out priorly, and moisture contents reported in other literature, just the initial C:N ratios were differentiated by mixing different amount of newspaper with the same amount of swine feces. This study was carried out by operating 4 experimental cornposting reactors of bench scale for 3 weeks. The followings are the conclusions that were derived from this study. 1. During composting reaction, the C:N ratio of each cornposter was decreased. Degree of decrease was in order of run 3, run 2, run 4, and run 1 of which initial C:N ratio was 30, 25, 35, and 20 respectively. All of the final composts were found to be completed composting reaction. 2. Ash contents of each reactor increased rapidly in order of run 3, run 2, run 4, and run 1. The absolute values of quadratic effect coefficients of each second order regression function was 0.059, 0.038, 0.032, and 0.030 respectively. Ash contents evolution trend had a linear correlation with the C:N ratio trend. (r=-0.96932, p<0.05) 3. The range of highest temperatures reached during composting was 47.2-53.5$\circ$C. Those were not significantly different from one another. Thermophilic temperatures were maintained in the range of 48-108 hours. 4. Contents of heavy metal detected in the final compost were lower than those of Korean and European standards. 5. Concentration range of Nitrogen in the final compost was 1.11-2.27%, and that of phosphorus was 8.40-10.70 mg/kg. 6. The optimum C:N ratio which has been proposed without the consideration of types of bulking agents should be re-examined. Biodegradabilities of each bulking agents was thought to be important factor when determining the optimum initial C:N ratio for cornposting.

• 동아시아식생활학회지
• /
• 제25권3호
• /
• pp.460-473
• /
• 2015

This study aimed to create a standardized recipe using three cultivars of tomatoes (Chal-tomato, Daejeo-tomato, Blacktomato) and select an appropriate tomato for producing tomato Jangajii through quality and sensory evaluation. With regard to the proximate composition of tomato Jangajii, moisture and ash contents of Chal-tomato were highest in the early stage of storage, whereas moisture, crude protein and ash contents of Black-tomato were highest in the final stage of storage. Daejeotomato showed minimal changes in pH, but showed the highest salt and sugar contents. L value increased with increasing storage time and then decreased thereafter (p<0.001). The a and b values decreased with increasing storage time and then increased thereafter (p<0.001). The reducing sugar content increased with increasing storage time and then decreased thereafter (p<0.001). With regard to Daejeo-tomato, hardness was the highest (p<0.001), and total microbial counts were lowest (p<0.001). Daejeo-tomato showed the lowest activities of PME as a softening enzyme and PG. For sensory properties, Daejeo-tomato showed a relatively high preference for all items except aroma. Based on the above results, Daejeo-tomato Jangajii showed superior quality characteristics and high preference in general among tomato Jangajii from all three cultivars of tomatoes. Therefore, Daejeo-tomato Jangajii is useful as low-sodium tomato Jangajii in light of quality characteristics and preference.

• 한국축산식품학회지
• /
• 제35권4호
• /
• pp.441-448
• /
• 2015

Blanching beef for use in home meal replacements (HMR) is an important process that determines the final quality of the beef after the cooking process. Thermal pretreatment also minimizes the change in quality during the main cooking process or storage. In this study, beef samples were washed and sliced, then treated by immersion in boiling water (1-10 min), steaming (1-10 min), or pan-frying in oil (30-240 s). The color after each thermal treatment showed higher L* and b* values and lower a* values compared with the raw beef, except for the pan-frying thermal treatment. The total color difference (∆E) and pH value were significantly increased by panfrying (p<0.05). There was no significant difference in the shear force of the beef samples, except for the sample pan-fried for 210 s. The nutritional content of beef was measured as the moisture, protein, fat, and ash contents, which were 69.96, 16.64, 3.49, and 1.13%, respectively, in raw beef. After thermal treatment, the crude protein and fat contents were increased, whereas the moisture and ash contents decreased. The mineral content, including Na, Mg, Fe, and Ca was highest after pan-frying. The heat treatment decreased microorganisms in all the samples. The total bacteria count in raw beef was 4.5-4.7 Log CFU/g, whereas the bacteria count decreased to 2.2-2.8 Log CFU/g after blanching. Thermophilic bacteria, coliform, mold, and yeast not detected in any thermally treated sample.

• 한국작물학회지
• /
• 제58권3호
• /
• pp.226-231
• /
• 2013

국내 쌀 품종의 아밀로오즈 함량에 따른 총 11종 쌀가루의 아밀로오즈 함량, 손상전분, 수분함량, 수분흡수 지수(WAI), 수분용해지수(WSI), 입도분포 및 호화특성을 분석하였다. 국내 메성 쌀 품종 쌀가루의 아밀로오즈 함량은 9.95-21.52, 중간찰성은 11.69 및 찰성은 7.09%의 아밀로오즈 함량을 나타냈으며, 유색미 메성품종은 17.06-18.36% 및 유색 찰성 품종은 7.04%의 아밀로오즈 함량을 나타내는 것으로 확인되었다. 국내 쌀품종 쌀가루의 수분함량은 7.19-13.89%를 나타내었고, 수분흡수지수(WAI) 및 수분용해지수(WSI)의 경우 각각 남일 및 동진찰이 가장 높게 나타났고, 수분함량이 높은 시료의 경우 손상전분 함량이 낮은 것을 확인하였다. 국내 11품종의 쌀가루 입도 분포는 27.61- 189.67 ${\mu}m$를 나타내었으며 일반 메성 신동진 이 189.67 ${\mu}m$로 가장 높은 입도를 나타내었으며, 일반메성 품종인 남일이 27.61 ${\mu}m$로 가장 낮은 입도분포를 나타내는 것으로 확인되었다. 또한 본 연구결과 쌀가루의 수분함량이 낮은 시료가 전분입도가 낮으나 손상전분 함량이 높은 것으로 확인되었으며, 일반 메성 품종의 경우 수분함량 및 입도가 작은 시료는 최고 점도 및 최종점도가 높고, 유색메성품종의 경우 수분함량 및 입도가 작은 시료는 점도가 낮은 결과를 나타냈다.

• 한국응용과학기술학회지
• /
• 제25권1호
• /
• pp.15-22
• /
• 2008

The effects of fillers on the mechanical and thermal properties of glass/novolac composites have been studied. The matrix polymer and reinforcement were novolac type phenolic resin and milled glass fiber, respectively. Three different fillers, such as calcium carbonate, aluminum oxide, and wood powder were used for glass fiber reinforced plastic(GFRP) manufacture. Gravity, moisture content, tensile and flexural strength were measured to analyze the mechanical properties of GFRP and the final composites was burned in the electronic furnace at $1000^{\circ}C$ to confirm thermal properties GFRP containing aluminium oxide shows the highest thermal stability with 32% of weight loss at $1000^{\circ}C$ for one hour. GFRP containing calcium carbonate shows the maximum flexural strength (146 MPa), but that containing wood powder dose the highest tensile strength (65 MPa). Conclusively, we found that the characteristics of final composites strongly depend on several factors, such as types of materials, contents and chemical affinity of fillers. Therefore, it is very important to set up the combination of fillers for GFRP manufacturing to improve both mechanical and thermal properties at the same time.