• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.989-994
• /
• 1995

Rigid porous carbon fiber composites with the uniform pore size distribution were prepared by vacuum forming from water slurries containing carbonized PAN fibers, a phenolic resin and ceramic binders. The composites were designed to use for highly efficient carbon fiber filters for particulate filtration and gas adsorption. As the as-received carbon fibers of 1mm in length were milled to an approximate average length of 300${\mu}{\textrm}{m}$, modulus of rupture (MOR) of the composite filter was increased from 1MPa to the value larger than 5 MPa. Modulus of rupture (MOR) for the composite filter fabricated using the milled carbon fiber was increased from 5 MPa to 10 MPa as the carbonization temperature of the PAN fiber was raised from 90$0^{\circ}C$ to 140$0^{\circ}C$. The air permeability and an average pore size of the composite filter were increased from 40 to 270cc/min.$\textrm{cm}^2$ and from 35 to 80${\mu}{\textrm}{m}$, respectively, as the apparent porosity increased from 80 to 95%. It was shown that the MOR of the carbon fiber composite filter was dependent primarily on the average length of carbon fiber, carbonization temperature and the type of bonding materials.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.1
• /
• pp.59-68
• /
• 1994

The effects of silt and clay, water temperature and salinity on the metabolic activities: rates of respiration, filtration and nitrogen excretion in the clam, Mactra veneriformis, were investigated in ranges of $0{\sim}250ppm,\;15{\sim}25^{\circ}C\;and\;10{\sim}30\%0$ respectively. The weight specific respiration rate decreased with shell length and significantly declined at lower temperatures and lower salinity levels. Average respiration rates, filtration rates and ammonia excretion rates of the clam groups declined as water temperature was lowered. The respiration rate(R) and the filtration rate(F) decreased as the concentration of silt and clay(C) increased, the relationships between the two parameters were expressed as a regression line, R=a+b LogC and LogF=a+b LogC, respectively. On the rearing experiment treated with 50ppm of silt and clay, the relationship between the accumulative mortality(M) and the elapsed day(T) was $M=0.0186T^{2.7965}$, and the median lethal time was calculated at 16.8 days. From the rearing experiment, both rate of respiration and ammonia nitrogen excretion of experimental groups and control groups decreased with elapsed days, the rates of experimental groups, especially declined more compared with those of the control groups.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.154-157
• /
• 2001

The effects of pleating parameters on the performance of cylindrical cartridge air filters was experimentally studied. The tested filters are 150 mm in outer diameter and 700 mm in length. As the pleat count increases, the pressure drop across a cartridge filter is decreased for a constant pleat depth and flow rate. This is due to the increased filtration area which brings out less pressure loss of the filter. However, in the case of the filters having the pleat depth of 40 mm, the inner diameter of the cartridges is so small that the pressure loss is greatly increased.

• Bulletin of the Korean Mathematical Society
• /
• v.31 no.1
• /
• pp.35-44
• /
• 1994

In this paper we study exponential growth of Betti numbers over artinian local rings. By the Change of Tor Formula the results in the paper extend to the asymptotic behavior of Betti numbers over Cohen-Macaulay local rings. Using the length function of an artinian ring we calculate an upper bound for the number of generators of modules, this is then used to maximize the number of generators of sygyzy modules. Finally, applying a filtration of an ideal, which we call a Loewy series of an ideal, we derive an invariant B(R) of an artinian local ring R, such that if B(R)>1, then the sequence $b^{R}$$_{i}$ (M) of Betti numbers is strictly increasing and has strong exponential growth for any finitely generated non-free R-module M (Theorem 2.7).).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.6
• /
• pp.639-643
• /
• 2002

Water quality, bacterial phase and fish growth rate were analyzed in the process of artificial seed production of flounder (Paralichtys oliraceus) larvae to investigate the water quality in rearing tank using Ultra Filtration System (UES). Sand Filtration System (SFS) and Ultra Filtration System (Ins) were set up in the experimental group. For the analysis of water quality, pH, salinity, DO, SS, COD, $NH_{4}^{+},\;NO_{2}^{-},\;NO^-,\;DIN$ (dissolved inorganic nitrogen) and DU (dissolved inorganic phosphate) were measured. There was no data difference between SFS group and UES group in most analysis items, but the UEs group showed low salinity and low 55 values, such that salinity was $33.5\%_{\circ}$ in SES group and $30.2\%_{\circ}$ in WS group and 55 was 15.5 mL/L in SES group and 7.0 mL/L for UPS group. For changes in bacterial phase and TBC (Total Bacterial Counts), in SES group, 6$\times$10^{5}CFU/mL in seawater decreased to the ratio of about 116, and TBC, Genus Vibrio and bacteria in the Genus Acinetobacter and Genus Micrococcus sharply increased after nine days, while stable bacterial phase was maintained low in UES group during the experiment except for Genus Ajteromonas. In the growth of the larvae, fish length was 17.0 mm (SGR 14.0) in the SES group and 18.8 mm (SGR 14.3) in the UFS group. It is concluded that when water is supplied for artificial seed production with WS, stabilization of water quality condition and inhibition of bacterial multiplication are possible. When production environment becomes stable, stable growth of fish becomes possible by reduction of environmental stress.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.1
• /
• pp.1-9
• /
• 2011

In order to investigate the cause and magnitude of scale effect occurring in the model experiments of fishing nets, five pairs of Nylon pyramid nets and one pair of PE ones in which all the two nets paired were equal each other in the factors determining their flow resistance, i. e., the ratio d/l of diameter d to length l of bars, the angle f between two adjacent bars, the attack angle q of nettings to the water flow, and the wall area S of nets, and different in the values of d and l were prepared. Then, the nets were attached to the circular steel frame alternately and their flow resistances with shapes in water were measured on the sea ascribing no turbulent flows by using the tension meter made of a block bearing for the experiment. All the Nylon nets were spreads out easily in water to form a circular cone at relatively low velocity of water and showed the resistance smaller a little in the nets with larger d and l than them with smaller d and l, because the filtration of water through meshes become easier in nets especially with larger l. But PE nettings were not spread out sufficiently on account of their small flexibility and showed higher resistance especially in them with thicker twines. Therefore, the difference in bar length or mesh size and flexibility of nettings between prototype and model nets are regarded to become factors ascribing scale effect. Especially the influence of the difference in mesh size may become large significantly in actual model experiments because the mesh size of model nets is decided at much larger value than that given by scale ratio and so the difference of mesh size between the two nets become much larger than that between nets used in this experiment.

• Journal of fish pathology
• /
• v.19 no.2
• /
• pp.99-108
• /
• 2006

Diseased tiger puffer (Takijugu rubripes) showed anorexia and severe anemia in the gills. In wet mount preparations Heterobothrium sp. with 4 sets of clamps on the opisthohaptor attached to the gill filaments of the diseased fish. From the drum-shaped filter for filtration of the culturing water and the sediment of aquarium held the diseased fish in the laboratory, their eggs forming long strings through connection of the bipolar filaments could be easily collected. The parasites with 4 pairs of clamps on the opisthohaptor were 2.38mm in length and 0.71 mm in width, but had no isthmus which was separated the opisthohapor from the body proper. The parasites could be easily distinguished from Heterobothrium tetrodonis and H. okamotoi in the absence of distinct isthmus, and resembled H. yamagutii described from the gills of Takifugu xanthopterus in Japan. Their eggs were yellowish spindle in shape and 180-200 x 5-6 Iffil in size, which were pointed at both ends. The eggs were linked to adjacent egg shells like a string of beads by the filaments. Onchomiracidia, ciliated larvae spawned from the eggs were 133 Iffil (120-146 Iffil) x 751ffil (68-80 Iffil) in size. The length of the ciliates was 12 Iffil in the anterior part of the larvae and 14 Iffil in the posterior part. Round or leaf-shaped young parasites attached on the secondary gill lamellae. There was a tendency that most of round smaller parasites without an opisthohaptor were found in the middle part of the gill lamellae while leaf-shaped larger ones with a opisthohaptor attached on the distal part of the gill filaments. Each clamp of mature parasites grasped one secondary gill filament which resulted in bending of the filaments and hyperplasia of the epithelium and mucous cells. In the branchial cavity around the pseudobranch, mature parasites grasped the adjacent ones by means of the clamps, and the epithelia of the branchial cavity around the parasites showed severe irregular hyperplasia and erosion with strongly PAS-positive mucous cells.

• Carbon letters
• /
• v.11 no.3
• /
• pp.184-191
• /
• 2010

Carbon nanotubes are unique tubular structures of nanometer diameter and large length/diameter ratio. The nanotubes may consist of one up to tens and hundreds of concentric shells of carbons with adjacent shells separation of ~0.34 nm. Multiwalled carbon nanotubes were synthesized by arc-discharge technique. MWCNTs were formed at the cathode deposit along with other carbonaceous materials like amorphous carbon, graphite etc. However, to get the best advantage of carbon nanotubes in various advanced applications, these undesired carbonaceous materials to be removed which is a challenging task. In the present study, various techniques were tried out for purifying MWCNTs such as physical filtration, chemical treatment and thermal annealing. SEM, FTIR, TGA and BET techniques were used to characterize the CNTs at various stages. Results shows that suitable chemical treatment followed by thermal annealing under controlled flow of oxygen gives the better route for purification of carbon nanotubes.

• Journal of Korean Society on Water Environment
• /
• v.22 no.5
• /
• pp.926-932
• /
• 2006

A series of bench-scale membrane filtration experiments were performed to systematically investigate the removal mechanisms of reverse osmosis (RO) and nanofiltration (NF) membranes for BTEX (benzene, toluene, ethylene, xylene), trichloroethylene (TCE) and tetrachloroethylene (PCE). The molecular weight of these organic compounds ranged from 78 to 166 dalton. The rejection of organic compounds by RO/NF membranes varied significantly from 59.6 to 99.2% depending on solute and membrane types. Specifically, experimental results demonstrated that the removal efficiency of RO/NF membranes increased as solute molecular characteristics such as W/L (molecular width/length) ${\times}$ $M_W$ (molecular weight) and octanol-water partition coefficient increased. This observation suggested that the rejection of small organic compounds by RO/NF membranes was determined by the combined effect of physical (molecular size and shape) and chemical (hydrophobicity) properties.

• Journal of Korean Society on Water Environment
• /
• v.26 no.1
• /
• pp.44-51
• /
• 2010

A lab-scale apparatus for turbid water transport control was tested and examined. The channel had a dimension of $100cm{\times}30cm{\times}15cm$ (length${\times}$hight${\times}$width). And the turbidity water was prepared using two types of particles, bentonite and loess. The channel equipped with filamentous mat was operated under various shock load conditions. In the control channel, instantly, turbid water mixed with the clean water inside the channel and turbidity prevails the entire channel. While in the mat-equipped channel, it increases only at the bottom. Overall, the filamentous mat gave capture efficiency of 70~90% compared with the control group. The capture efficiency of turbid particles decreased with increased input turbidity flux. The result of experimental run on how turbid particles are separated in the mat channel shows that settling, filtration and attachment are the main processes. Meanwhile, turbidity was diffused from the channel bottom due to turbidity gradient before and after mat zone. The particle size before mat zone was lightly coarser than that after mat zone.