• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.36-43
• /
• 2006

There was some difficulty dewatering properties due to small porosity diameter of cake, when pigment sludge contained fine particle was formed by cake under the dewatering. It was difficult to dewater the sludge with fine particles with the conventional mechanical dewatering method. This study was to improve the dewatering rate as discharging the water from porosity of cake easily, supplying the low heat to the cake layer. Thermal dewatering equipment of piston type to keep up constant temperature on the cake was set up and relative experiment was conducted for sludge of 200 g with fine pigment particle. As test results. filtration of 176.8 g, cake weight of 19.4 g, cake thickness of 4.2 mm was measured, and it was analyzed that the water content of cake was 47 wt% and dewatering velocity, which moaned the residual d교 sloid amount per dewatering area, was $2.1DS\;m^{2}{\cdot}cycle$. This results showed that filtration increased, cake weight and thickness decreased and dewatering velocity increased against mechanical dewatering method. And water content of cake decreased about 30%, so the result which dewatering rate improved was drew generally. The reason is that the inner vapor pressure working at the cake porosity increased as applying the low heat to the cake layer, which lead to discharge the water from porosity easily. Therefore, this study was estimated by the useful technology for sludge reduction.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.5
• /
• pp.1477-1488
• /
• 2014

Prevalent construction of impermeable pavements in urban areas causes diverse water-related environmental issues, such as lowering ground water levels and shortage of water supply for the living. In order to resolve such problems, a rainwater reservoir can be an effective and useful solution. The rainwater reservoir facilitates the hydrologic cycle in urban areas by temporarily retaining precipitation-runoff within a shallow subsurface layer for later use in a dry season. However, in order to use the stored water of precipitation-runoff, non-point source pollutants mostly retained in initial rainfall should be removed before being stored in the reservoir. Therefore, the purification system to filter out the non-point source pollutants is essential for the rainwater reservoir. The conventional soil filtration technology is well known to be able to capture non-point source pollutants in a economical and efficient way. This study adopted a sand filter layer (SFL) as a non-point source pollutant removal system in the rainwater reservoir, and conducted a series of lab-scale chamber tests and field tests to evaluate the pollutant removal efficiency and applicability of SFL. During the laboratory chamber experiments, three types of SFL with the different grain size characteristics were compared in the chamber with a dimension of $20cm{\times}30cm{\times}60cm$. To evaluate performance of the reservoir systems, the concentration of the polluted water in terms of TSS (Total Suspended Solids) and COD (Chemical Oxygen Demand) were measured and compared. In addition, a reduction in hydraulic conductivity of SFL due to pollutant clogging was indirectly estimated. The optimum SFL selected through the laboratory chamber experiments was verified on the in-situ rainwater reservoir for field applicability.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.2
• /
• pp.63-71
• /
• 2011

A large volume of uranium electrokinetic leachate has been generated during the electrokinetic decontamination to remove uranium from contaminated soil. The treatment technology for the reuse of the uranium leachate was developed. The concentration of uranium in the generated uranium leachate was 180 ppm and concentrations of Mg(II), K(I), Fe(II), and Al(III) ions ranged from 20 ppm to 1,210 ppm. The treatment process for uranium leachate consisted mainly of mixing and cohesion, precipitation, concentration, and filtration. In order to obtain the pH=11 of a precipitate solution, the calcium hydroxide needs to be 3.0g/100ml and the sodium hydroxide needed to be 2.7g/100ml. The results of several precipitation experiments showed that a mixture of NaOH+0.2g alum+0.15g magnetite was an optimal precipitant for filtration. The average particle size of precipitate with NaOH+alum+0.15g magnetite was $600\;{\mu}m$. Because the total value of metal concentrations in supernatant at pH=9 was the smallest, sodium hydroxide should be added with 0.2g alum and 0.15g magnetite for pH=9 of leachate.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.113.2-113.2
• /
• 2010

세라믹 필터는 여러 종류의 분진제거 시스템에서 연소 배가스 정제를 위한 가장 적절한 소재로 알려져 있다. 현재까지 다양한 형태의 세라믹 필터가 개발되고 있는데, 캔들 타입(candle type), 튜브 타입(tubular type), 평판 타입(parallel flow type) 등이 그 예이다. 통상적으로 세라믹 캔들 필터는 가압유동층복합발전(PFBC, Pressurize Fluidized-Bed Combustion), 석탄가스화복합발전(IGCC, Integrated coal Gasification Combined Cycle), 석탄가스화연료전지복합발전(IGFC, Integrated coal Gasification Fuel cell Combined cycle)에서 고온 배가스 정제용으로 사용되고 있다. 일반적으로 IGCC나 CTL 합성가스 정제시스템의 경우에는 높은 고압(약 25기압)과 미세분진이 함유되어 있는 분위기에서 운전된다. 그러므로 이때 사용되는 초청정용 세라믹 집진필터는 고온, 고압 및 부식 환경에서 50 MPa 이상을 갖는 높은 강도와 내식성을 갖도록 개발되어야 하기 때문에 SiC(Silicon Carbide)가 가장 적절한 캔들 필터 소재로 적용되고 있다. 이에 따라 집진용 SiC 세라믹 캔들 필터를 개발하기 위해서는 고온에서 내산화성이 우수하고, 부피팽창에 의한 균열이 발생하지 않는 무기결합재의 선정 및 이를 통한 소재의 특성 최적화가 가장 중요한 부분이라 할 수 있다. 본 연구에서는 래밍성형 공정을 적용하여 1m급 탄화규소 세라믹 캔들 필터 시작품을 제조하였으며, 래밍성형 공정 이외에 정수압가압성형, 진공압출성형으로 제조되고 있는 세라믹 캔들 필터의 국내외 시장 및 그 전망을 분석하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.109.2-109.2
• /
• 2010

세라믹 필터는 여러 종류의 분진제거 시스템에서 연소 배가스 정제를 위한 가장 적절한 소재로 알려져 있다. 현재까지 다양한 형태의 세라믹 필터가 개발되고 있는데, 캔들 타입(candle type), 튜브 타입(tubular type), 평판 타입(parallel flow type) 등이 그 예이다. 통상적으로 세라믹 캔들 필터는 가압유동층복합발전(PFBC, Pressurize Fluidized-Bed Combustion), 석탄가스화복합발전(IGCC, Integrated coal Gasification Combined Cycle), 석탄가스화연료전지복합발전(IGFC, Integrated coal Gasification Fuel cell Combined cycle)에서 고온 배가스 정제용으로 사용되고 있다. 일반적으로 IGCC나 CTL 합성가스 정제시스템의 경우에는 높은 고압(약 25기압)과 미세분진이 함유되어 있는 분위기에서 운전된다. 그러므로 이때 사용되는 초청정용 세라믹 집진필터는 고온, 고압 및 부식 환경에서 50 MPa 이상을 갖는 높은 강도와 내식성을 갖도록 개발되어야 하기 때문에 SiC(Silicon Carbide)가 가장 적절한 캔들 필터 소재로 적용되고 있다. 이에 따라 집진용 SiC 세라믹 캔들 필터를 개발하기 위해서는 고온에서 내산화성이 우수하고, 부피팽창에 의한 균열이 발생하지 않는 무기결합재의 선정 및 이를 통한 소재의 특성 최적화가 가장 중요한 부분이라 할 수 있다. 본 연구에서는 IGCC나 CTL 공정에 적용하기 위한 SiC 캔들 필터 소재 개발을 위해 래밍성형 공정으로 1m급의 탄화규소 캔들 필터 시작품을 제작하여 SiC 출발입자 크기와 무기계 결합재인 스트론튬 카보네이트의 첨가량 변화에 따른 필터 소재의 특성 평가를 수행하였다.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.1
• /
• pp.47-53
• /
• 2018

This study investigated phosphorus removal from secondary treated effluent using coagulation-membrane separation hybrid treatment to satisfy strict regulation in wastewater treatment. The membrane separation process was used to remove suspended phosphorus particles after coagulation/settlement. Membrane separation with $0.2{\mu}m$ pore size of micro filtration membrane could reduce phosphorus concentration to 0.02 mg P/L after coagulation with 1 mg Al/L dose of polyaluminum chloride (PACl). Regardless of coagulant, the residual concentration of phosphorus decreased as the dose increased from 1.5 to 3.5 mg Al/L, while the target concentration of 0.05 mg P/L or less was achieved at 2.5 mg Al/L for the aluminum sulfate (Alum) and 3.5 mg Al/L for PACl. Moreover, alum showed better membrane flux as make bigger particles than PACl. Alum showed a 40% of flux decrease at 2.5 mg Al/L dose, while PACl indicated a 50% decrease of membrane flux even with a higher dose of 3.5 mg Al/L. Thus, alum was more effective coagulant than PACl considering phosphorus removal and membrane flux as well as its dose. Consequently, the coagulation-membrane separation hybrid treatment could be mitigate regulation on phosphorus removal as unsettleable phosphorus particles were effectively removed by membrane after coagulation.

• Journal of Wetlands Research
• /
• v.13 no.2
• /
• pp.199-208
• /
• 2011

Scarcity of water worldwide, increasing greenhouse gas emissions, increased energy consumption due to the Earth is threatened. Existing in the process of urban planning and development of forests, rivers and other natural ecosystems have been destroyed and that there was increased impervious pavement. Impervious pavement increase water circulation system to destroy the natural and urban water retention, infiltration and decreased evaporation. Nonpoint source pollution(NPS) occurs when rainfall impervious pavement and appeal directly to the river water inflow is adversely impacts of the situation. In this study, rainfall occurs impervious pavement NPS pollution reduction and temperature increase due to the increase in urban areas, and to solve heat island phenomenon is to develop small HSSF constructed wetland technology. The small HSSF constructed wetland sedimentation, filtration, adsorption, absorption by vegetation, including such mechanisms. Techniques for verification of the pilot-scale test was conducted. In the future domestic urban heat island phenomenon and restore the natural water cycle for the facilities will be used as a basis to develop.

• The Korean Journal of Zoology
• /
• v.36 no.1
• /
• pp.97-108
• /
• 1993

The biochemical characteristics of immunorecative atrial natriuretic peptide (irAUPP and the changes in the levels of irANP in the heart were investigated during the metamorphosis of frog tadpoles. Immunohistochemical localization of pro-ANP in cardiocfes and the presence of irAW in the peritoneal fluid of metamorphosing tadpoles were also examined. The major form of irANP in the cardiocvtes of tadpoles (Rana omurensisp was high molecular weight on gel filtration chromatographv and reverse-phase HPLC. The levels of irANP in the atrium of tadpoles were five to seven times higher than those in the ventricle. In metamorphosing tadpoles the levels of irANP in the atrium increased at stage XX, the climax of metamorphosis, and decreased at stage XXV (P < 0.051, the completion of metamorphosis. When the levels of irANP was expressed as a function of body weight of tadpoles, a continuous increase in the levels of irANP was observed from pre- to postmetamorphosis (P < 0.051. The levels of irAUP in the ventricle were found to be higher in the adult frogs than in tadpoles (R. omurensisl (P < 0.01). Pro-ANP (31-67) immunoreactivity was detected in the ventricle as well as in the atrium of tadpoles fR. nigromaculotal. The peritoneal fluid was also found to contain low molecular weight of irAUP and the levmils of irANP were 55.4 $\pm$ 9.1 pg/ml. Changes of the level of irANP at different stases of the life cycle suggest that ANP may play a role in the regulation of body fluid homeostasis of frog tadpoles during the metamorphosis.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.5
• /
• pp.619-627
• /
• 2012

In order to determine reduction of greenhouse gas emissions (GHGs) when the submerged membrane bioreactor with granular sulfur (MBR-GS) is used in wastewater treatment plant (WTP), the amount of GHGs was compared and analyzed in the advanced treatment process of P wastewater treatment plant (WTP). The amount of GHGs was estimated by classifying as construction and operation phase in WTP. The amount of GHGs in construction phase was evaluated from multiplying raw materials by using carbon emission factors. Also the amount of GHGs in operating phase was calculated by using total electricity consumption and carbon emission factor. The construction of anoxic tank and secondary settling tank is unnecessary, because the MBR-GS conducts simultaneously the nitrification and denitrification in aeration tank and filtration by hollow fiber membrane. The amount of $CO_2$, $CH_4$, and $N_2O$ emitted by constructing the MBR-GS was 6.44E+06 kg, 8.16E+03 kg and 1.38E+01 kg, respectively. The result shows that the GHGs was reduced about 47 % as compared with the construction in the MLE process. In operating the MBR-GS, the electricity is not required in the biological reactor and secondary setting tank. Thus, the amount of $CO_2$, $CH_4$, and $N_2O$ emitted by operating in the MBR-GS was 7.39E+05 kg/yr, 5.80E+02 kg/yr and 2.44E+00 kg/yr, respectively. The result shows that the GHGs were reduced about 37 % as compared with the operation in the MLE process. Also, $LCCO_2$(Life Cycle $CO_2$) was compared and analyzed between MLE process and MBR-GS. The amount of $LCCO_2 $emitted from the MLE process and MBR-GS was 3.56E+04 ton $CO_2$ and 2.12E+04 ton $CO_2$, respectively. The result shows that the GHGs in MBR-GS were reduced to about 40 % as compared in the MLE process during life cycle. As a result, sulfur-utilizing autotrophic denitrification process (SADP) is expected to be utilized as the cost-effective advanced treatment process, owing to not only high nitrogen removal efficiency but also the GHGs reduction in construction and operation stage.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.426-438
• /
• 2023

Lithium-sulfur batteries, recently attracting attention as next-generation batteries, have high energy density but are limited in application due to sulfur's insulating properties, shuttle phenomenon, and volume expansion. This study used an economical and simple vacuum filtration method to prepare a freestanding electrode without a binder and collector. Carbon nanotubes (CNTs) are used to improve the electrical conductivity of sulfur, where CNT also acts as both collector and conductor. In addition, metal oxides (MO_x, M=Ni, Mg), which are easy to adsorb lithium polysulfide, are added to the CNT/S electrode to suppress the shuttle reaction in lithium-sulfur batteries, which is a result of suppressing the loss of active sulfur material due to the excellent adsorption of lithium polysulfide by metal oxides. The MO_x@CNT/S electrode exhibited higher capacity characteristics and cycle stability than the CNT/S electrode without metal oxides. Among the MO_x@CNT/S electrodes, the NiO@CNT/S electrode displayed a high discharge capacity of 780 mAh g^-1 at 1 C and an extreme capacity decrease to 134 mAh g^-1 after 200 cycles. Although the MgO@CNT/S electrode exhibited a low discharge rate of 544 mAh g^-1 in the initial cycle, it showed good cycle stability with 90% of capacity retention up to 200 cycles. Further, to achieve high capacity and cycle stability, the Ni_0.7Mg_0.3O@CNT/S electrode, mixed with Ni:Mg in the ratio of 0.7:0.3, manifested an initial discharge rate of 755 mAh g^-1 (1 C) and a capacity retention rate of more than 90% after 200 cycles. Therefore, applying binary metal oxides to CNT/S provides a freestanding electrode for developing economical and high-performance Li-S batteries, effectively improving lithium polysulfide's high capacity characteristics and dissolution.