• 한국축산식품학회지
• /
• 제43권6호
• /
• pp.1128-1149
• /
• 2023

In order to extend the shelf life of refrigerating raw lamb by inhibiting the growth of microorganisms, preventing the oxidation of fat and protein, and absorbing the juice outflow of lamb during storage, an active packaging system based on plastic/gelatin bilayer film with essential oil was developed in this study. Three kinds of petroleum-derived plastic films, oriented polypropylene (OPP), polyethylene terephthalate, and polyethylene, were coated with gelatin to make bilayer films for lamb preservation. The results showed significant improvement in the mechanical properties, oxygen, moisture, and light barriers of the bilayer films compared to the gelatin film. The OPP/gelatin bilayer film was selected for further experiments because of its highest acceptance by panelists. If the amount of juice outflow was less than 350% of the mass of the gelatin layer, it was difficult for the gelatin film to separate from lamb. With the increase in essential oil concentration, the water absorption capacity decreased. The OPP/gelatin bilayer films with 20% mustard or 10% oregano essential oils inhibited the growth of bacteria in lamb and displayed better mechanical properties. Essential oil decreased the brightness and light transmittance of the bilayer films and made the film yellow. In conclusion, our results suggested that the active packaging system based on OPP/gelatin bilayer film was more suitable for raw lamb preservation than single-layer gelatin film or petroleum-derived plastic film, but need further study, including minimizing the amount of essential oil, enhancing the mechanical strength of the gelatin film after water absorption.

• Journal of Pharmaceutical Investigation
• /
• 제33권3호
• /
• pp.163-169
• /
• 2003

In order to develop a film-forming transdermal drug delivery system, polyurethane (PU) based on poly(ethylene glycol) and poly(tetramethylene oxide) was synthesized and characterized. The synthesized PU was blended with Gantrez ES 225 (GT) to improve the adhesion property of film-forming agent to the skin. When film-forming gel formulation containing 3% ketoprofen (KP) was applied, transparent thin film was obtained within 5 minutes and adhered to the skin for 8 hours. In vitro percutaneous absortion studies were performed to determine the rate of ketoprofen absorption through guinea pig skin. A prominent effect of limonene on the skin permeability of ketoprofen was observed among the various skin permeation enhancers investigated. Considering mechanica properties of film and skin permeability of ketoprofen, 2% of limonene was optimal content in the film forming transdermal formulation.

• Journal of Multimedia Information System
• /
• 제7권2호
• /
• pp.157-164
• /
• 2020

Considering the frustration affordability level of college entrants and investigating the frustration tolerance of undergraduates in Shenyang City University, this paper provides the basis for the research of improving frustration tolerance of undergraduates through quantitative research results and applies film therapy to the frustration regulation of college students by discussing the role of film therapy in improving frustration affordability ability of college entrants. This paper has concluded that the necessary of improving the frustration tolerance of college students in Northeast China and the feasibility of the film therapy programs on improving the frustration tolerance of college students in Northeast China. Meanwhile, this paper shows that the principle of film selection in film therapy should be based on the requirements of the aesthetics of the film industry in the IT environment. This paper provides a reference for refining the target of film therapy for film therapists to better apply film and television psychotherapy technology, and a basis for the film therapy activity program; Furthermore, it also has a certain reference significance for film and television media workers.

• 한국전기전자재료학회논문지
• /
• 제11권6호
• /
• pp.458-464
• /
• 1998

This paper gives characterization of substrate and PZT(53/47) thin film deposited by metalorganic decomposition, which is concerned in deposition process and device fabrication process, to fabricate micro electro mechanical system (MEMS) device with piezoelectric material. The PZT thin films deposited by MOD at 700^{\circ}C$ for 30 minutes had a polycrystallinity, that is, no substrate dependence, while different interface were developed depending on the bottom electrodes. Such a structural variation could influence on not only the properties of the PZT film but also etching process for fabricating MEMS devices. Therefore the electrode structure is a very important factor in the deposition of the PZT film during etching process by HF acid for MEMS device with piezoelectric material. Piezoelectric coefficients of the PZT films on the different substrates were 40 and 80 pm/V at an applied voltage of 4V. Based in these results, it was possible for deposition of the PZT film by MOD to apply MEMS device fabrication process based on piezoelectricity after selection of proper bottom electrode.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.673-680
• /
• 2015

A roll-to-roll (R2R) continuous manufacturing system for a carbon-nanotube (CNT)-/silver-nanowire (AgNW)- based large-area transparent conductive film was introduced in this study. The systemic guidelines of the R2R slot-die coating process including roll eccentricity, wrap angle, pump accuracy, and blower influence were discussed. To simulate the coating phenomenon, we investigated the governing parameters of the coating process by incorporating the estimated relative thickness that was defined by combining the viscocapillary model and volume model. By using experimental and mathematical approaches, an excellent transparent conductive layer with a $40{\Omega}/{\Box}$ sheet resistance and 88 % transmittance was obtained; moreover, a dimensionless number identifies the correlation between the transparent conductive film and the anti-reflection film.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4329-4337
• /
• 2022

Jet impinging device is designed for decay heat removal on horizontal fuel rods in a low temperature heating reactor. An experimental system with a fuel rod simulator is established and experiments are performed to evaluate water film covering capacity, within 0.0287-0.0444 kg/ms mass flow rate, 0-164.1 kW/m² heating flux and 13.8-91.4℃ feeding water temperature. An effective method to obtain the film coverage rate by infrared equipment is proposed. Water film flowing patterns are recoded and the film coverage rates at different circumference angles are measured. It is found the film coverage rate decreases with heating flux during single-phase convection, while increases after onset of nucleate boiling. Besides, film coverage rate is found affected by Marangoni effect and film accelerating effect, and surface wetting is significantly facilitated by bubble behavior. Based on the observed phenomenon and physical mechanism, dry-out depth and initial dry-out rate are proposed to evaluate film covering potential on a heating surface. A model to predict film coverage rate is proposed based on the data. The findings would have reliable guide and important implications for further evaluation and design of decay heat removal system of new reactors, and could be helpful for passive containment cooling research.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.41.2-41.2
• /
• 2011

Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Metal Oxide Semiconductor) based electronic devices become much faster speed and smaller size than ever before. However, very narrow interconnect line width causes some drawbacks. For example, deposition of conformal and thin barrier is not easy moreover metallization process needs deposition of diffusion barrier and glue layer. Therefore, there is not enough space for copper filling process. In order to overcome these negative effects, simple process of copper metallization is required. In this research, Cu-V thin alloy film was formed by using RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane $SiO_2$/Si bi-layer substrate with smooth and uniform surface. Cu-V film thickness was about 50 nm. Cu-V layer was deposited at RT, 100, 150, 200, and $250^{\circ}C$. XRD, AFM, Hall measurement system, and XPS were used to analyze Cu-V thin film. For the barrier formation, Cu-V film was annealed at 200, 300, 400, 500, and $600^{\circ}C$ (1 hour). As a result, V-based thin interlayer between Cu-V film and $SiO_2$ dielectric layer was formed by itself with annealing. Thin interlayer was confirmed by TEM (Transmission Electron Microscope) analysis. Barrier thermal stability was tested with I-V (for measuring leakage current) and XRD analysis after 300, 400, 500, 600, and $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However V-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Thus, thermal stability of vanadium-based thin interlayer as diffusion barrier is good for copper interconnection.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1370-1376
• /
• 2003

The investigation of liquid fuel film on the cylinder liner is an essential to understand the engine-out hydrocarbon emissions formation in SI engines. In this research, two-dimensional visualization was carried out to investigate the liquid fuel film on the quartz liner in the optical engine. For this, the optical engine with hydraulic system was designed based on the commercial SI engine. The visualization was based on the laser-induced fluorescence with total reflection technique. Using a quartz liner and a special lens, only the liquid fuel film on the liner was visualized. With using this technique, the distribution of the fuel film on the cylinder liner was measured for different engine conditions and injection timing in the optical engine.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2008년도 하계종합학술대회
• /
• pp.789-790
• /
• 2008

In this paper, we introduce the multi-target-based auto surveillance algorithm. Multi-target-based surveillance system detects intrusion objects in the specified areas. The proposed algorithm can divide into two parts: i) background generation, ii) object extraction. In this paper, one of the optical flow equation methods for estimation of gradient method used to generate the background [2]. In addition, the objects and back- ground video images that are continually entering the differential extraction.

• 한국전기전자재료학회논문지
• /
• 제15권3호
• /
• pp.281-286
• /
• 2002

In odder to investigate the magnetic properties of CoCr-based bilayered thin films on kind of underlayer, we introduced amorphous Si layer to Co-Cr(-Ta) magnetic layer as underlayer. First, we prepared CoCr and CoCrTa single layer using the Facing Targets Sputtering system to investigate theirs properties. It was revealed that with increasing the film thickness of CoCr, CoCrTa single layer, crystalline orientation and perpendicular coercivity was improved. The CoCrTa thin film showed bettor crystalline and magnetic characteristics than CoCr thin film. As a result of investigating magnetic properties of CoCr and CoCrTa magnetic layer on introducing the Si underlayer, perpendicular coercivity and saturation magnetization of CoCr/Si and CoCrTa/Si bilayered thin film were decreased due to the increased grain size and diffusion of Si atoms to magnetic layer. And they showed constant with increasing the film thickness of Si thin film. However, in case of CoCrTa/Si bilayered thin film, in-plane coercivity was controlled low at about 250Oe. The c-axis orientations of CoCr/si and CoCrTa/Si bilayered thin film showed a good crystalline characteristics as about $2^{\circ}$.