• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.721-724
• /
• 2005

With the advantages of large vibration energy dissipation of structures, the granular materials are used as vibration and acoustic treatments. In this case of vibro acoustic controls, a finite dynamic strength of the solid component (frame) is an important design factor. The dynamic stiffness of hollow cylindrical beams containing porous and granular materials as damping treatment was measured. Using the Rayleigh-Ritz method, the effects of damping materials on the dynamic characteristics of beams were investigated. The results suggested that the acoustic structure Interaction between the frame and the structure enhances the dissipation of the vibration energy significantly. The same methods were applied also to vibration control of sandwich panels. By filling the cavities of honeycomb cores using unconsolidated granular materials, its sound transmission toss was improved significantly.

• Carbon letters
• /
• v.2 no.3_4
• /
• pp.165-169
• /
• 2001

Modification of C/C composite bipolar plate for improving electrical conductivity was carried out by addition of electroconductive carbon black (EC-CB). Carbon black was carefully mixed to methanol-containing phenolic resin, impregnated into 2D-carbon fabrics, hot pressed and then carbonized to obtain composite plate. Inclusion of electro-conductive carbon black enhanced the electrical conductivity of the C/C composites by increasing the conduction path. Addition of 10 vol% carbon black increased the electrical conductivity from 5.5/${\Omega}cm$ to 32/${\Omega}cm$ and reduced the crack formation by filling effect, resulting in the increase of flexural properties of composite plate. However, at carbon black content over 10 vol%, flexural properties decreased by delaminating role of excess carbon black at the interface in C/C composites.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1463-1470
• /
• 2018

In this study, 20 types of samples were prepared by mixing different kinds of inorganic materials to develop insulation materials for epoxy - based GIS substation equipment used under high voltage environmentally friendly insulation gas. One of the electrical characteristics, AC insulation breakdown experiment was performed. As mixing ratio of mixed heterogeneous inorganic materials, the dielectric breakdown strength was increased with increasing filler ratio of micro silica, micro silica : micro Alumina, 1:9, 3:7, 5:5, 7:3, 9:1, and decreased as the filling amount of micro alumina increased. The AC insulation breakdown characteristics were the best when the composition ratio was 9:1. The higher the content of silica, the better the interfacial properties, and the larger the alumina content ratio, the worse the interfacial properties.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.413-416
• /
• 2003

Experimental tests on the high strength self-compacting concrete with light-weight fine aggregate and light-weight coarse aggregate(LHSSC) were performed with slump-flow, reaching time to the slump-flow of 500mm, V-funnel dropping time and U-box difference level and compressive strength. LHSCC with light-weight fine aggregate of 75% and light-weight coarse aggregate of 100% was only satisfied with the property conditions of second self-compacting concrete(SCC), like as flowability, resistance to segregation and filling ability. The 28-day compressive strength of LHSCC indicated above 300kgf/$\textrm{cm}^2$ in all concrete mixtures, and it was increased to increase the replacement ratio of light-weight fine aggregate or to decrease the replacement ratio of light-weight coarse aggregate. Therefore, for satisfying the properties of fresh SCC and hardened concrete with above 350kgf/$\textrm{cm}^2$, it would expected that the replacement ratio of light-weight fine aggregate and light-weight coarse aggregate will be determined with 50~75% and 25~50%, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.74-77
• /
• 2003

This paper investigated the apparent chloride diffusivity of various concretes. Ten mixtures of concrete were initially prepared and tested to estimate diffusion property. The penetration depth and concentration of chloride ion were examined at the same water-binder ration. The binders were composed of normal portland cement, fly ash, ground granulated blast-furnace slag, and silica fume. From the results, it was concluded that using the mineral admixtures had a filling effect on the pore structure of cements matrix due to those pozzoanic reaction with the hydrates of cement, which increases the tortuosity of pore and makes large pore finer. And diffusivity of chloride is following: NPC100 > F10N90 > F30N70 > F20N80 > F20S05 > G30N70 > F10S05 > G30S05 > G30F15 > G50N50.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.500-503
• /
• 2002

In this paper, we demonstrate the deformation of TFT-LCD panel using numerical analysis based on the finite element method. To make better uniform cell gap and less stress at a photo-definable spacer (spacer), we have investigated process and design factors such as amount of liquid crystal (LC), spacer density, area, height, and material property. Furthermore we optimized design factors and achieved the robust design through the simulation.

• Tribology and Lubricants
• /
• v.12 no.2
• /
• pp.32-40
• /
• 1996

The tribological role of copper alloy fine particles in an additive is not well known compared to solid lubricants such as $MoS_{2}$ and PTFE. In this experimental investigation, a series of friction and wear test was undertaken to gain a better understanding of an additive containing copper alloy fine particles and to identify the effectiveness of copper alloy particles in improving tribological performance of the lubricant. Friction and wear of specimens under lubricated contact condition were studied and the worn surfaces were characterized by AES (Auger Electron Spectroscopy), SEM (Scanning Electron Microscopy) and optical microscopy. It was revealed that a copper-contained layer was formed and this layer resulted in considerable reduction in both friction and wear due to its lubricity and anti-wear property. The analysis of worn surface revealed that copper of the fine alloy particles in the additive helps healing the worn surface by plating and filling wear pits.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.09a
• /
• pp.3-12
• /
• 2006

The main feature of these total technologies is that we can constitute the optimum treatment scheme fitting to the property of wastes, amount of wastes and energy requirement. For high moisture content wastes or biomass resources, high pressure steam process (MMCS) for crush, dry and deodorize wastes to produce high quality fertilizer of fuel is most appropriate. For dry or semi-dry solid wastes, the STAR-MEET system can be applied to produce low-BTU gases for power generation using duel fueled diesel engines of Stirling engines, and the REPRES and HyPR-MEET systems can be applied to produce hydrogen rich medium-BTU gas. For waste plastics and oils, liquefaction technology is best fit to produce light oil or kerosene equivalent fuel oils. These total technologies are completely different from the existent waste treatment technologies based on land-filling or incineration, and are expected to disseminate all over the world in the near future.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.253-256
• /
• 2000

In order to commercialize the low cost composite fabrication technology in the area of domestic aerospace structure field, Resin Transfer Molding process has been considered as an alternative process to replace the high cost autoclave technology. The end part for the development of RTM process is the control rod of flight control system of aircraft. A braided preform was triaxially designed to improve the dimensional stability and mechanical property in the direction of external loads. Through the flow analysis using CVFEM, the resin filling time was calculated and the resin injection method was determined. The results of the flow analysis were directly applied to RTM mold design. The control rod was successfully manufactured by RTM process using internal pressure. The length and outer diameter of the manufactured part are 1148mm and 32mm, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.497-500
• /
• 2004

Recently, the use of structure compound waterproof agent (hereinafter referred to as 'SCWA') that is used when manufacturing concrete for concrete structures, increases in quantity. However, while it is expected that the SCWA that is mixed in the concrete inside can significantly affect the change of physical properties that lift the internal force of a structure. This study has been conducted through an experiment for the effects of cement hardener on the formation of microscopic texture, and newly generated hydrates from that result were not confirmed in the present experiment. It was found that at the hydrate reaction it has the property that can be hardened within the limit of pore diameterar a specific size rather than there is the internal gap filling capacity due to generating other hydrates.