• Applied Biological Chemistry
• /
• v.47 no.3
• /
• pp.344-350
• /
• 2004

This study was conducted to develop and assess the applicability of mixed-bed ion exchange resin capsules for water quality monitoring in small agricultural watershed. Recoveries of resin capsules for inorganic N and P ranged from 96 to 102%. The net activation energies and pseudo-thermodynamic parameters, such as ${\Delta}G^{o\ddag},\;{\Delta}H^{o\ddag},\;and\;{\Delta}S^{o\ddag}$ for ion adsorption by resin capsules, exhibited relatively low values, indicating the process might be governed by chemical reactions such as diffusion. However, those values increased with temperature coinciding with the theory. The reaction reached pseudo-equilibrium within 24 hours for $NH_4-N\;and\;NO_3-N$, and only 8 hours for $PO_4-P$, respectively. The selectivity of resin capsules were in the order of $NO_3\;^-\;>\;NH_4\;^+\;>\;PO_4\;^{3-}$, coinciding with that of encapsulated Amberlite IRN-150 resin. At the initial state of equilibrium, the resin adsorption quantity was linearly proportional to the mass of ions in the streams, but the rate of movement leveled off, following Langmuir-type sorption isotherm. The overall results demonstrated that the resin capsule system was suitable for water quality monitoring in small agricultural watershed, judging from the reaction mechanism(s) of the resin capsule and the significance of model in field calibration.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.1
• /
• pp.51-62
• /
• 2020

This study was conducted to develop a method for depth assessment of embedded sources using gamma-spectrum ratio and for the evaluation of field applicability. To this end, Peak to Compton and Peak to valley ratio changes were evaluated according to ¹³⁷Cs, ⁶⁰Co, ¹⁵²Eu point source depth using HPGe detector and MCNP simulation. The effects of measurement distance of PTV and PTC methods were evaluated. Using the results, the source depth assessment equation using the PTC and PTV methods was derived based on the detection distance of 50 cm. In addition, the sensitivity of detection distance changes was assessed when using PTV and PTC methods, and error increased by 3 to 4 cm when detection distance decreased by 20 cm based on 50 cm. However, it was confirmed that if the detection distance was increased to 100 cm, the effects of detection distance were small. And PTV and PTC methods were compared with the two distance measurement method which evaluates the depth of source by the change of net peak counting rate according to the detection distance. As a result of source depth assessment, the PTV and PTC showed a maximum error of 1.87 cm and the two distance measurement method showed maximum error of 2.69 cm. The results of the experiment confirmed that the accuracy of the PTV and PTC methods was higher than two distance measurement. In addition, Sensitivity evaluation by horizontal position error of source has maximum error of less than 25.59 cm for the two distance measurement method. On the other hand, PTV and PTC method showed high accuracy with maximum error of less than 8.04 cm. In addition, the PTC method has lowest standard deviation for the same time measurement, which is expected to enable rapid measurement.

• Economic and Environmental Geology
• /
• v.50 no.6
• /
• pp.537-544
• /
• 2017

Stable carbon isotope ratio of carbon dioxide (${\delta}^{13}C_{CO2}$) is used as an important indicator in the researches for global climate change and carbon capture and sequestration technology. The ${\delta}^{13}C$ value has been usually analyzed with Isotope Ratio Mass Spectrometer (IRMS). Recently, the use of Laser Absorption Spectrometry (LAS) is increasing because of the cost efficiency and field applicability. The purpose of this study was to suggest practical procedures to prepare laboratory reference gases for ${\delta}^{13}C_{CO2}$ analysis using LAS. $CO_2$ gas was adjusted to have the concentrations within the analytical range. Then, the concentration of $CO_2$ was assessed in a lab approved by the Korea Laboratory Accreditation Scheme and the ${\delta}^{13}C_{CO2}$ value was measured by IRMS. When the instrument ran over 12 hours, the ${\delta}^{13}C$ values were drifted up to ${\pm}10$‰ if the concentration of $CO_2$ was shifted up to 1.0% of relative standard deviation. Therefore, periodical investigation of analytical suitability and correction should be conducted. Because ${\delta}^{13}C_{CO2}$ showed the dependency on $CO_2$ concentration, we suggested the equation for calibrating the concentration effect. After calibration, ${\delta}^{13}C_{CO2}$ was well matched with the result of IRMS within ${\pm}0.52$‰.

• Geophysics and Geophysical Exploration
• /
• v.12 no.1
• /
• pp.56-68
• /
• 2009

Ongoing and extensive urbanisation, which is frequently accompanied with careless construction works, may threaten important archaeological structures that are still buried in the urban areas. Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT) methods are most promising alternatives for resolving buried archaeological structures in urban territories. In this work, three case studies are presented, each of which involves an integrated geophysical survey employing the surface three-dimensional (3D) ERT and GPR techniques, in order to archaeologically characterise the investigated areas. The test field sites are located at the historical centres of two of the most populated cities of the island of Crete, in Greece. The ERT and GPR data were collected along a dense network of parallel profiles. The subsurface resistivity structure was reconstructed by processing the apparent resistivity data with a 3D inversion algorithm. The GPR sections were processed with a systematic way, applying specific filters to the data in order to enhance their information content. Finally, horizontal depth slices representing the 3D variation of the physical properties were created. The GPR and ERT images significantly contributed in reconstructing the complex subsurface properties in these urban areas. Strong GPR reflections and highresistivity anomalies were correlated with possible archaeological structures. Subsequent excavations in specific places at both sites verified the geophysical results. The specific case studies demonstrated the applicability of ERT and GPR techniques during the design and construction stages of urban infrastructure works, indicating areas of archaeological significance and guiding archaeological excavations before construction work.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.5
• /
• pp.667-673
• /
• 2005

The purposes of this study were 1) to analyze the preference of leadership style among ${\lceil}$Transformational leadership$\rfloor$ and ${\lceil}$Service leadership$\rfloor$, 2) to examine the differences of the job satisfaction between the high level of service leadership group and low level of the service leadership group and 3) to testify the hypothesis that the service leadership and its 4 elements (belief, attitude, ability, insight) affect the job satisfaction. The questionnaires were developed to measure the service leadership, the preference of leadership style (transfer-mational leadership and service leadership) and Job satisfaction. The surveys were distributed to 120 managers and employees in the family restaurant in Korea, and 104 questionnaires were responded (response rate: $86.7\%$). The SPSS 12.0 package program was used to conduct the descriptive analysis, correlation analysis, t-test and multiple regression analysis. The result of leadership style preference showed the followers preferred the service leadership $(75.0\%)$ to the transformational leadership $(25.0\%)$. Comparing the job satisfaction of high level of service leadership group and that of low level of service leadership group, the job satisfaction of high level of service leadership group was significantly (p<0.001) higher than that of low level of service leadership group (high level of service leadership group: 4.03, low service leadership group: 3.27, measured on a 5-point likert scale). All three factors of job satisfaction (human factor, service system and company image) in high level of leadership group were significantly (p<0.001) higher than those of lower level of service leadership group. The result of multiple regression analysis presented that the service leadership and it's 4 elements (concept, mind, skill, insight) have significant (p=0.000) effects on the job satisfaction. As a conclusion, we examined theoretical framework of service leadership model and testified the applicability in the field of family restaurants. But the service leadership was the new conceptual theory, so there should be the more empirical studies on managers and employees in the service industry.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.271-278
• /
• 2006

Investigations of underground cavities are required to provide useful information for the reinforcement design and monitoring of the ground subsidence areas. It is, therefore, necessary to develop integrated geophysical techniques incorporating different geophysical methods in order to accurately image and to map underground cavities in the ground subsidence areas. In this study, we conducted geophysical investigations for development of integrated geophysical techniques to detect underground cavities at the field test site in the ground subsidence area, located at Yongweol-ri, Muan-eup, Muan-gun, Jeollanam-do. We examined the applicability of geophysical methods such as electrical resistivity, electromagnetic, and microgravity to cavity detection with the aid of borehole survey results. The underground cavities are widely present within the limestone bedrock overlain by the alluvial deposits in the test site where the ground subsidences have occurred in the past. The limestone cavities are mostly filled with groundwater or clays saturated with water in the site. The cavities, thus, have low electrical resistivity and density compared to the surrounding host bedrock. The results of the study have shown that the zones of low resistivity and density correspond to the zones of the cavities identified in the boreholes at the site, and that the geophysical methods used are very effective to detect the underground cavities. Furthermore, we could map the distribution of cavities more precisely with the study results incorporated from the various geophysical methods. It is also important to notice that the microgravity method, which has rarely used in Korea, is a very promising tool to detect underground cavities.

• Journal of Bio-Environment Control
• /
• v.24 no.2
• /
• pp.123-127
• /
• 2015

Wood piles are rarely used in the construction of a greenhouse in Korea, but they are relatively more often used in other countries, such as the Netherlands. There are several advantages associated with wood piles: they are more cost-effective, less time-consuming, and more ecofriendly than the steel pipes (SPs) and pre-stressed highstrength (PHC) piles. However, one of the limiting conditions is that they have to be installed below the groundwater level to prevent decay. Since the groundwater levels are generally high in the reclaimed lands in Korea, wood piles are expected to be used often as reinforcements for foundations of greenhouses in these areas. In this study, we measured the uplift capacities of wood piles through in-situ uplift capacity tests with an aim to provide basic design data for wood pile foundations. In order to test their applicability, we then compared these experimentally measured ultimate uplift capacities with the ones calculated through some of the existing theoretical equations. The wood piles used in the loading tests were made of softwood (pine wood), and the tests were performed using piles with different diameters (∅25cm and ∅30cm) and embedded depths (1m, 3m, and 5m). The test results revealed that the uplift capacity of the wood piles showed a clear linearly increasing tendency in proportion to the embedded depth, with the ultimate uplift capacities for the diameters 25cm and 30cm being 9.38 and 10.56tf, respectively, at the embedded depth of 5m; thus demonstrating uplift capacities of ${\geq}9tf$. The comparison between the actually measured values of the uplift capacity and the ones calculated through equations revealed that the latter, which were obtained using the ${\alpha}$ method, were generally in an approximate agreement with the in-situ measured values.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.6
• /
• pp.346-361
• /
• 2013

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2012. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. The conclusions are as follows : (1) The research works on thermal and fluid engineering have been reviewed as groups of fluid machinery, pipes and valves, fuel cells and power plants, ground-coupled heat pumps, and general heat and mass transfer systems. Research issues are mainly focused on new and renewable energy systems, such as fuel cells, ocean thermal energy conversion power plants, and ground-coupled heat pump systems. (2) Research works on the heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer, and industrial heat exchangers. Researches on heat transfer characteristics included the results for natural convection in a square enclosure with two hot circular cylinders, non-uniform grooved tube considering tube expansion, single-tube annular baffle system, broadcasting LED light with ion wind generator, mechanical property and microstructure of SA213 P92 boiler pipe steel, and flat plate using multiple tripping wires. In the area of pool boiling and condensing heat transfer, researches on the design of a micro-channel heat exchanger for a heat pump, numerical simulation of a heat pump evaporator considering the pressure drop in the distributor and capillary tubes, critical heat flux on a thermoexcel-E enhanced surface, and the performance of a fin-and-tube condenser with non-uniform air distribution and different tube types were actively carried out. In the area of industrial heat exchangers, researches on a plate heat exchanger type dehumidifier, fin-tube heat exchanger, an electric circuit transient analogy model in a vertical closed loop ground heat exchanger, heat transfer characteristics of a double skin window for plant factory, a regenerative heat exchanger depending on its porous structure, and various types of plate heat exchangers were performed. (3) In the field of refrigeration, various studies were executed to improve refrigeration system performance, and to evaluate the applicability of alternative refrigerants and new components. Various topics were presented in the area of refrigeration cycle. Research issues mainly focused on the enhancement of the system performance. In the alternative refrigerant area, studies on CO2, R32/R152a mixture, and R1234yf were performed. Studies on the design and performance analysis of various compressors and evaporator were executed. (4) In building mechanical system research fields, twenty-nine studies were conducted to achieve effective design of mechanical systems, and also to maximize the energy efficiency of buildings. The topics of the studies included heating and cooling, HVAC system, ventilation, renewable energy systems, and lighting systems in buildings. New designs and performance tests using numerical methods and experiments provide useful information and key data, which can improve the energy efficiency of buildings. (5) In the fields of the architectural environment, studies for various purposes, such as indoor environment, building energy, and renewable energy were performed. In particular, building energy-related researches and renewable energy systems have been mainly studied, reflecting interests in global climate change, and efforts to reduce building energy consumption by government and architectural specialists. In addition, many researches have been conducted regarding indoor environments.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.3
• /
• pp.252-260
• /
• 2011

BACKGROUND: Currently, national biomass inventory are being established for efficient management of the potential energy sources. Among the various types of biomass, agricultural wastes are considered to take the biggest portion of the total annual biomass generated in Korea, implying its importance. However, the currently estimated amount is not reliable because the old reference data are still used to estimate total annual amount of agricultural wastes. METHODS AND RESULTS: Therefore, to provide reliable estimation data, a correct conversion factor obtained by taking into account the current situation is required. For this, the current study was conducted to provide the conversion factors for each representative 8 crop through a field cultivation study. Also conversion factors for 18 crops were calculated using the average amount of each crop produced during 2004 and 2008, subsequently; total amount of agricultural wastes generated in 2009 was estimated using these conversion factors. The total biomass of rice straw and rice husk generated in 2009 were 6.5 and 1.1 million tons, respectively, which consist 75% of the total agricultural based wastes, while the total biomass of pepper shoots and apple pruning twigs were 1.0 and 0.6 million tons, respectively. Despite the high amount of rice-based biomass, their applicability for bio-energy production is low due to conventional utilization of these materials for animal feeds and beds for animal husbandry. In addition to exact estimation of the total biomass, temporal variations in both generated amount and the type of agricultural biomass materials are also important for efficient utilization; fruit pruning twigs (January to March); barley-, been-, and mustard-related waste materials (April to June); rice-related waste (September to October). CONCLUSION(s): Such information provided in this study can be used to establish a master plan for efficient utilization of the agricultural wastes on purpose of bio-energy production.

• Journal of Korean Society on Water Environment
• /
• v.23 no.4
• /
• pp.467-473
• /
• 2007

Although the dominant land use at the Imha-dam watershed is forest areas, soil erosion has been increasing because of intensive agricultural activities performed at the fields located along the stream for easy-access to water supply and relatively favorable topography. In addition, steep topography at the Imha-dam watershed is also contributing increased soil erosion and sediment loads. At the Imha-dam watershed, outflow has increased sharply by the typhoons Rusa and Maemi in 2002, 2003 respectively. In this study, the Soil and Water Assessment Tool (SWAT) model was evaluated for simulation of flow and sediment behaviors with long-term temporal and spatial conditions. The precipitation data from eight precipitation observatories, located at Ilwol, Subi and etc., were used. There was no significant difference in monthly rainfall for 8 locations. However, there was slight differences in rainfall amounts and patterns in 2003 and 2004. The topographical map at 1:5000 scale from the National Geographic Information Institute was used to define watershed boundaries, the detailed soil map at 1:25,000 scale from the National Institute of Highland Agriculture and the land cover data from the Korea Institute of Water and Environment were used to simulate the hydrologic response and soil erosion and sediment behaviors. To evaluate hydrologic component of the SWAT model, calibration was performed for the period from Jan. 2002 to Dec. 2003, and validation for Jan. 2004 to Apr. 2005. The $R^2$ value and El value were 0.93 and 0.90 respectively for calibration period, and the $R^2$ value and El value for validation were 0.73 and 0.68 respectively. The $R^2$ value and El value of sediment yield data with the calibrated parameters was 0.89 and 0.84 respectively. The comparisons with the measured data showed that the SWAT model is applicable to simulate hydrology and sediment behaviors at Imha dam watershed. With proper representation of the Best Management Practices (BM Ps) in the SWAT model, the SWAT can be used for pre-evaluation of the cost-effective and sustainable soil erosion BMPs to solve sediment issues at the Imha-dam watershed. In Korea, the Universal Soil Loss Equation (USLE) has been used to estimate the soil loss for over 30 years. However, there are limitations in the field scale mdel, USLE when applied for watershed. Also, the soil loss changes temporarily and spatially, for example, the Imha-dam watershed. Thus, the SW AT model, capable of simulating hydrologic and soil erosion/sediment behaviors temporarily and spatially at watershed scale, should be used to solve the muddy water issues at the Imha-dam watershed to establish more effective muddy water reduction countermeasure.