• 한국재료학회지
• /
• 제13권4호
• /
• pp.213-218
• /
• 2003

Fibrous monolithic control of$ Al_2$$O_3$ -$ZrO_2$composite was investigated by multi-pass extrusion process. To obtain sound $Al_2$$O_3$-X $O_2$sintered bodies, burning out and sintering process were carefully carried out. The sintered bodies showed continuous, fibrous monolithic microstructure without any swelling. Many microcracks were observed at the $Al_2$$O_3$-$ZrO_2$interfaces due to the mismatching of thermal expansion coefficient between $Al_2$$O_3$ and $ZrO_2$phase. Most of m- $ZrO_2$grains included twin defects such as (001), (010) and (011) type to accommodate the phase transformation induced stress.

• 펄프종이기술
• /
• 제37권3호
• /
• pp.50-58
• /
• 2005

It is generally known that paper industry is the second largest industry in the use of process water, and also have the highest environmental impact load in the contaminant sources. Paper is produced from the mixtures composed of 1% fibrous raw materials and 99% water. The optimum use of process water effects on the quality properties of paper and the environmental impact load of waste water treatment. In this research, the kinds of fibrous raw material & additives used in the paperboard production line were investigated, and the quantification of environmental loads and the environmental effects of process water on COD potential were evaluated. The NBDCODs were also analyzed from process water by the method of waste water treatment in paper mill and applied for the optimum use of recycling water, and zero effluent process. In the fibrous raw materials, KOCC caused the highest COD potentials, and sack paper & UKP was comparatively low. The NBDCOD of KOCC largely reduced after biological treatment because of easily biodegradable properties, but AOCC contained non-biodegradable materials. In chemical additives, COD was high in turns of rosin>starch>deaeration agent>dye, NBDCOD greatly reduced in starch and deaeration agent. In the case of 2 kinds of paperboard product, the COD potentials was mainly high in starch, AOCC and KOCC.

• 열처리공학회지
• /
• 제14권4호
• /
• pp.205-211
• /
• 2001

The characteristics of super duplex stainless steel were investigated on its fibrous structure and dispersed structure. These structures consist of various volume fractions and distributions of the austenite phase that were obtained by changing the heat treatment temperature and cycle. The fibrous structure had higher austenite volume fraction than dispersed structure on the same temperature. As the austenite volume fraction increased in both structures, tensile strength and elongation increased, but hardness decreased. Fatigue life of fibrous structure parallel to rolling direction was shorter than that of perpendicular to rolling direction. Fatigue life of dispersed structure was longer than parallel fibrous structure, and shorter than perpendicular fibrous structure. Fatigue crack propagation rate of fibrous structure was faster than that of dispersed structure.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제14권1_2호
• /
• pp.124-134
• /
• 1992

Fibrous dysplasia is a benign pathologic condition of bone in which fibrous tissue gradually expands and replaces normal bone into fibro-osseous lesion. It is a primary developmental abnormality of bone-forming mesenchyme in origin. This study shows clinical history, radiological and histopathological feature of fibrous dysplasia with the intention of establishing correct diagnosis, treatment plan and evaluation of prognosis. This paper reviews and summarizes the materials from 57 fibrous dysplasias submitted to the Department of Oral and Maxillofacial Surgery in College of Dentistry, Seoul National University. Conclusions obtained were as following : 1. Fibrous dysplasia developed mainly in teenagers and shows female predeliction. 2. Fibrous dysplasia developed much on the maxilla 3. Monostotic fibrous dysplasia was most popular form. 4. Main symptom of fibrous dysplasia was painless swelling. 5. Radiological feature of fibrous dysplasia was ground-glass appearance, 6. Histopathological feature of fibrous dysplasia was irregular immature bony trabeculae(woven bone). 7. Treatment of fibrous dysplasia was mainly conservative contouring surgery.

• 한국세라믹학회지
• /
• 제45권8호
• /
• pp.443-452
• /
• 2008

Shrinkage crack is a major concern for cement materials, especially for flat structures such as Korean On-Dol floor system, flooring for garages, and wall. One of the methods to reduce the adverse effects of shrinkage cracking is to reinforce cement materials with shot randomly distributed fibers. The efficiency of inorganic fibrous material to arresting cracks in cementitious composites was studied. Cement materials reinforced with five different qualities of inorganic fibrous material were tested. Contents of inorganic fibrous material were 1.0 kg, 1.5 kg, 2.0 kg, 2.5 kg, 3.0 kg by weight of cement mortar and C : S types of cement mortar were 1:3 and 1:4. W/C were 60% and 80%. Cement mortar of inorganic fibrous material reinforcement showed an ability to reduce the crack width and crack length significantly as compared to unreinforced cement mortar. $40%{\sim}60%$ drop in shrinkage crack of 1:4 cement mortar with 1.5 kg over was observed.

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.215-220
• /
• 2015

The PVDF fibrous composite filled with iron oxide nanoparticles were prepared by using the electrospinning technique. The electrospun composite have the thickness in the range of $60-80{\mu}m$ with the average fibrous diameters of 500-900 nm. The magnetizations of PVDF fibrous composite filled with iron oxide nanoparticles showed 4.5 emu/g, 3.1 emu/g and 1.6 emu/g at 1.5 T of external magnetic field for 20 wt.%, 10 wt.% and 5 wt.% iron oxide nanoparticles, respectively. The heat elevation of the magnetic composite were measured under various AC magnetic fields, frequency and the ambient temperatures. The temperature reached up to $46.3^{\circ}C$ from $36^{\circ}C$ at 128 Oe and 355 kHz for 20 wt.% iron oxide nanoparticles filled in PVDF fibrous composite sheet. The specific absorption rate of theses sheets increased from 0.041 W/g to 0.236 W/g with the increment of AC magnetic field from 90 Oe to 167 Oe at 190 kHz, respectively.

• 펄프종이기술
• /
• 제44권6호
• /
• pp.58-69
• /
• 2012

As the meaning of dictionary terminology, scum refers to a layer of impurities that accumulates at the surface of a liquid. In papermaking process, scum indicates the floated solid waste generated by a flotation process during the primary wastewater treatment. In this study, different kinds of stocks and scums collected from newspaper, liner, tissue and fine paper were analysed in details. The purpose of this study was firstly to demonstrate the composition characteristics of different sources of scum, secondly the analysis of environmental hazardous materials, and thirdly the evaluation of reutilization ability of fibrous materials from collected scum. As mentioned the meaning of solid waste, scum was actually differ from the waste sludge in sources, compositions and recycling abilities. In the same manner of waste paper, the sludge which is generated within onsite of papermaking processes would be reused as a raw material. The general compositions of scum from waste water were mainly inorganic ash materials, fine fibre fractions, recycled fibre debries, and ink particles. If the scum is able to reuse as fibrous additives in papermaking process, it could contribute to the savings of running costs in both the subsidiaries of fibrous material and the solid waste treatment with even small quantity.

• 한국분말재료학회지
• /
• 제26권5호
• /
• pp.383-388
• /
• 2019

To improve the mechanical properties of aluminum, graphene has been used as a reinforcing material, yielding graphene-reinforced aluminum matrix composites (GRAMCs). Dispersion of graphene materials is an important factor that affects the properties of GRAMCs, which are mainly manufactured by mechanical mixing methods such as ball milling. However, the use of only mechanical mixing process is limited to achieve homogeneous dispersion of graphene. To overcome this problem, in this study, we have prepared composite materials by coating aluminum particles with graphene by a self-assembly reaction using poly vinylalcohol and ethylene diamine as coupling agents. The scanning electron microscopy and Fourier-transform infrared spectroscopy results confirm the coating of graphene on the Al surface. Bulk density of the sintered composites by spark plasma sintering achieved a relative density of over 99% up to 0.5 wt.% graphene oxide content.

• 한국재료학회지
• /
• 제32권2호
• /
• pp.107-113
• /
• 2022

Fibrous supercapacitors (FSs), owing to their high power density, good safety characteristic, and high flexibility, have recently been in the spotlight as energy storage devices for wearable electronics. However, despite these advantages, FCs face many challenges related to their active material of carbon fiber (CF). CF has low surface area and poor wettability between electrode and electrolyte, which result in low capacitance and poor long-term stability at high current densities. To overcome these limits, fibrous supercapacitors made using surface-activated CF (FS-SACF) are here suggested; these materials have improved specific surface area and better wettability, obtained by introducing porous structure and oxygen-containing functional groups on the CF surface, respectively, through surface engineering. The FS-SACF shows an improved ion diffusion coefficient and better electrochemical performance, including high specific capacity of 223.6 mF cm^-2 at current density of 10 ㎂ cm^-2, high-rate performance of 171.2 mF cm^-2 at current density of 50.0 ㎂ cm^-2, and remarkable, ultrafast cycling stability (96.2 % after 1,000 cycles at current density of 250.0 ㎂ cm^-2). The excellent electrochemical performance is definitely due to the effects of surface functionalization on CF, leading to improved specific surface area and superior ion diffusion capability.

• Geomechanics and Engineering
• /
• 제5권2호
• /
• pp.87-97
• /
• 2013

In this paper, a novel fibrous material known as axially reinforced braided composite rods (BCRs) have been developed for reinforcement of soils. These innovative materials consist of an axial reinforcement system, comprised of longitudinally oriented core fibres, which is responsible for mechanical performance and, a braided cover, which gives a ribbed surface texture for better interfacial interactions with soils. BCRs were produced using both thermosetting (unsaturated polyester) and thermoplastic (polypropylene) matrices and synthetic (carbon, glass, HT polyethylene), as well as natural (sisal) core fibres. BCRs were characterized for tensile properties and the influence of core fibres was studied. Moreover, BCRs containing carbon fibre in the core composition were characterized for piezoresistivity and strain sensing properties under flexural deformation. According to the experimental results, the developed braided composites showed tailorable and wide range of mechanical properties, depending on the core fibres and exhibited very good strain sensing behavior.