• 한국농공학회논문집
• /
• 제47권2호
• /
• pp.63-72
• /
• 2005

In this study, the physical and mechanical properties of steel fiber reinforced lightweight polymer concrete were investigated experimentally with various steel fiber contents. All tests were performed at room temperature, and stress-strain curve and load-deflection curve were plotted up to failure. The unit weight of steel fiber reinforced lightweight polymer concrete was in the range of $1,020{\sim}1,160\;kg/m^3$, which was approximately $50\%$ of that of the ordinary polymer concrete, The compressive strength, splitting tensile strength, flexural toughness and flexural load-deflection curves after maximum load were shown with increase of steel fiber content. The stress-strain curves of steel fiber reinforced lightweight polymer concrete were bilinear in nature with a small transition zone, Based on these results, steel fiber reinforced lightweight polymer concrete can be widely applied to the polymer composite products.

• 한국농공학회지
• /
• 제45권7호
• /
• pp.11-19
• /
• 2003

In this study, unsaturated polyester resin, artificial lightweight coarse aggregate, artificial lightweight fine aggregate, heavy calcium carbonate and steel fiber were used to produce a steel fiber-reinforced lightweight polymer concrete with which mechanical properties were examined. Results of this experimental study showed that the flexural strength of unnotched steel fiber-reinforced lightweight polymer concrete increased from 8.61 to 13.96 MPa when mixing ratio of fiber content increased from 0 to 1.5%. Stress intensity factors($K_{IC}$) increased with increasing fiber content ratio while it did not increase with increasing notch ratio. Energy release rate ($G_{IC}$) turned out to depend upon the notch size, and it increased with increasing steel fiber content.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.613-616
• /
• 1999

The bond between reinforcing bar and concrete is a significant factor to confirm that they behave uniformly in the reinforced concrete. Thus, the studies on this field have been conducted by many researchers. But for the high strength lightweight concrete few studies have been done. In this study, the steel fiber reinforced high strength lightweight concrete developed to complement the brittleness of the high strength lightweight concrete was studied experimentally to find the local bond stress. Total 20 specimens were tested and the measured test values were compared with those calculated according to ACI 318-95 code and CEB-FIP code, respectively. The results indicate that the maximum bond stress has been influenced by increment of volume fracture of steel fiber, compressive strength and cover, Especially steel fiber caused not only increment of bond strength but also ductile behaviro.

• Computers and Concrete
• /
• 제29권 6호
• /
• pp.393-405
• /
• 2022

Lightweight concrete is a superior material due to its light weight and high strength. There however remain significant lacunae in engineering knowledge with regards to shear failure of lightweight fiber reinforced concrete beams. The main aim of the present study is to investigate the optimum usage of steel fibers in lightweight fiber reinforced concrete (LWFRC). Multi-scale finite element model calibrated with experimental results is developed to study the effect of steel fibers on the mechanical properties of LWFRC beams. To decrease the amount of steel fibers, it is preferred to reinforce only the middle section of the LWFRC beams, where the flexural stresses are higher. For numerical simulation, a multi-scale finite element model was developed. The cement matrix was modeled as homogeneous and uniform material and both steel fibers and lightweight coarse aggregates were randomly distributed within the matrix. Considering more realistic assumptions, the bonding between fibers and cement matrix was considered with the Cohesive Zone Model (CZM) and its parameters were determined using the model update method. Furthermore, conformity of Load-Crack Mouth Opening Displacement (CMOD) curves obtained from numerical modeling and experimental test results of notched beams under center-point loading tests were investigated. Validating the finite element model results with experimental tests, the effects of fibers' volume fraction, and the length of the reinforced middle section, on flexural and residual strengths of LWFRC, were studied. Results indicate that using steel fibers in a specified length of the concrete beam with high flexural stresses, and considerable savings can be achieved in using steel fibers. Reducing the length of the reinforced middle section from 50 to 30 cm in specimens containing 10 kg/m3 of steel fibers, resulting in a considerable decrease of the used steel fibers by four times, whereas only a 7% reduction in bearing capacity was observed. Therefore, determining an appropriate length of the reinforced middle section is an essential parameter in reducing fibers, usage leading to more affordable construction costs.

• Structural Engineering and Mechanics
• /
• 제73권4호
• /
• pp.437-445
• /
• 2020

The microstructure and mechanical properties of concrete will degrade significantly at high temperatures, thus affecting the bond strength between reinforcing steel and surrounding concrete in reinforced concrete members. In this study, the effect of individual and hybrid fiber on the local bond-slip behavior of lightweight aggregate concrete (LWAC) after exposure to elevated temperatures was experimentally investigated. Tests were conducted on local pullout specimens (150 mm cubes) with a reinforcing bar embedded in the center section. The embedment lengths of the pullout specimens were 4.2 times the bar diameter. The parameters investigated included concrete type (control group: ordinary LWAC; experimental group: fiber reinforced LWAC), concrete strength, fiber type, and targeted temperature. The test results showed that for medium-strength LWACs exposed to high temperatures, the use of only steel fibers did not significantly increase the residual bond strength. Moreover, the addition of individual and hybrid fiber had little effect on the residual bond strength of the high-strength LWAC after exposure to a temperature of 800℃.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1990년도 봄 학술발표회 논문집
• /
• pp.11-15
• /
• 1990

Results of an experimental study on the manufacture and the mechanical properties of carbon fiber reinforced fly ash-cement composites are presented in this paper. The carbon fiber reinforced fly ash-cement composites using silica powder and a small amount of Ethylene vinyl acetate emulsion are prepared with carbon fiber, foaming agents and curing conditions. As a result, the manufacturing process technology of carbon fiber reinforced fly ash-cement composites is developed. And the mechanical properties such as compressive, tensile and flexural strengths and drying shrinkage of lightweight carbon fiber reinforced fly ash-cement composites are improved by using a small amount of Ethylene vinyle acetate emulsion. The development and applications of precast products and the design systems of lightweight carbon fiber reinforced fly ash-cement composites are expected in the near future.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권4호
• /
• pp.57-66
• /
• 2015

본 연구는 경량콘크리트와 GFRP 보강근을 휨보강근으로 사용하여 제작되는 GFRP 보강근 경량콘크리트 슬래브를 교량 슬래브 등에 활용해보기 위한 사전 연구로서, 기존의 철근 콘크리트 슬래브와 GFRP 보강근 경량콘크리트 슬래브의 휨 거동 차이점 분석에 초점을 두었다. 이를 위하여 일련의 슬래브 실험체들을 제작하고 3점 휨 실험 및 수치해석을 행하였다. 실험 결과, GFRP 보강근 경량콘크리트 슬래브 실험체는 GFRP 보강근의 과다보강으로 인하여 실험체 하부에 발생된 초기균열이 하중 재하면의 콘크리트 압축부까지 연결되면서 전단파괴되는 경향을 보였다. 그리고 철근 콘크리트로 제작된 슬래브 실험체에 비하여 무게는 72%이었으며 휨 실험에서의 파괴하중은 58%인 것으로 나타났다. 한편, midas FEA를 이용하여 행한 수치해석 과정은 실험에서 나타난 전단파괴 하중까지 잘 모사하였다. 그러나 GFRP 보강근의 인장강도 대신 탄성계수가 입력값으로 요구됨에 따라 가력되는 하중과 처짐은 실험에서 나타난 전단파괴 이후에도 계속하여 증가하는 경향을 보였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.461-464
• /
• 2006

An experimental study is conducted to charaterize the mechanical properties of a fiber-reinforced, lightweight concrete (FRLAC) that is produced without an autoclave process. The FRLAC enhances the strength of lightweight cellular concrete by adding polypropylene fibers. A series of compressive strength tests on cylindrical specimens are carried out to characterize the compressive strength and the modulus of elasticity of the FRLAC. Specifically, various mixing rates of a foam agent are applied in casting of the specimens to investigate the influence of the mixing rate of the foam agent on the performance of the FRLAC and to determine the optimal mixing rate of the foam agent.

• Computers and Concrete
• /
• 제33권1호
• /
• pp.41-53
• /
• 2024

Under constant and cyclic axial compression, square composite short columns reinforced with Self Compacting Concrete (SCC) added with scrap rubber infilled inside steel tubes and with different types of concrete were cast and tested. The test is carried out to find the effectiveness of utilizing an aggregate manufactured from industrial waste and to address the problems associated with the need for alternative reinforcements along with waste management. The main testing parameters are the type of concrete, the effect of fiber inclusion, and the significance of rubber-infilled steel tubes. The failure modes of the columns and axial load-displacement curves of the steel tube-reinforced columns were all thoroughly investigated. According to the test results, all specimens failed due to compression failure with a longitudinal crack along the loading axis. The fiber-reinforced column specimens demonstrated improved ductility and energy absorption. In comparison to the normal-weight concrete columns, the lightweight concrete columns significantly improved the axial load-carrying capacity. The addition of basalt fiber to the columns significantly increased the yield stress and ultimate stress to 9.21%. The corresponding displacement at yield load and ultimate load was reduced to 10.36% and 28.79%, respectively. The precision of volumetric information regarding the obtained crack quantification, aggregates, and the fiber in concrete is studied in detail through image processing using MATLAB environment.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2003년도 학술발표논문집
• /
• pp.367-370
• /
• 2003

Lightweight polymer concrete with steel fiber can be used for thin panel, high building and large span structures due to its may advantages such as its durability, low weight, control of crack propagation, high strength and toughness. This study experimented about steel fiber reinforcement of lightweight polymer concrete using synthetic lightweight aggregate. The test result shows that the maximum strain and elastic modulus are in the range of $0.012{\sim}0.014\;and\;50.2{\times}10^3{\sim}51.0{\times}10^3kgf/cm^2$, respectively. The flexural load-deflection curves after maximum load are shown in smoothly with increase of steel fiber content