• 펄프종이기술
• /
• 제38권5호
• /
• pp.9-15
• /
• 2006

Wet compaction test (WCT) is a fiber evaluation method where wet fibers are compressed at one side of a cylinder and water drains out from the other side. The consistency of the fiber furnishes and their pressures are recorded during the test. In the previous study we found that WCT results always gave better coefficients of determination in fiber furnish drainage, and paper properties (density, tensile, tear, and burst strength) than those of WRV (water retention value). Fiber freeness and fiber length correlated well with drainage and tear strength of the furnishes, respectively; however, their correlations were very much improved by combining the WCT results. In this study, we used the WCT test for fractionated fiber furnishes to see whether improvement of the WCT is possible. We found that strength properties such as breaking length and burst index were correlated better with the fractionated long fiber furnishes. Drainage was greatly affected by the presence of short fiber furnishes. We used bleached chemical pulps (SwBKP, HwBKP), recycled pulp (OCC), and mechanical pulp (BCTMP) as fiber furnishes in this study. Fiber fractionation can be performed on-line in these days by using multifractor and WCT can be used as an on-line test in papermachine in the future.

• 한국의류산업학회지
• /
• 제19권2호
• /
• pp.240-248
• /
• 2017

This study compares general jacquard fabrics and jacquard fabrics with optical fiber on mechanical properties, sensibility and preference evaluation of fabric for the blind. The analysis also assesses the effect of optical fiber in the evaluation and identifies those best suited for consumers. The mechanical properties of jacquard fabrics were measured by the KES-FB system. Sensibility and the preference of the jacquard fabric for the blind were rated on tactile sensation by women experts in their 20's and 30's. It was found that the optical fiber in jacquard fabric affected the change of mechanical properties as well as sensibility and preference. Jacquard fabric with optical fiber were softer and more transformable, while the fabrics had lower recover property by shear force and compression as well as more violent unevenness. Jacquard fabrics were also classified into three hand factors of surface property, resilience and weightiness. There were significant differences on surface property perceptions and weightiness, hand and blind preferences by optical fiber. Jacquard fabrics that contained optical fiber were not preferred by the blind because they were perceived to be uneven and heavy. Those, that were smooth and light, were preferred for jacquard fabric; in addition, fabrics preferred by the blind had good compression.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.32-33
• /
• 2014

In this study, evaluation on weight loss properties of spalling control fiber with heating rates has been conducted. For evaluation of this study, 3types of organic fibers(Polyethylene, Polypropylene, Nylon) are used as spaling control fiber. Also, to evaluate the effect of heating rate to spallin control fiber, heating rates are set as 10, 25℃/min. As a result, the start time of weight loss of fiber with various heating rate was delayed as heating rate was increased.

• 비파괴검사학회지
• /
• 제27권2호
• /
• pp.148-156
• /
• 2007

섬유복합재료의 역학적인 관점에서 볼 때 PVA-ECC (polyvinyl alcohol-engineered cementitious composite)의 섬유분산성 평가는 매우 중요한 요소이다. 그러나 PVA 섬유의 낮은 명암비 때문에 시멘트계 재료와 섬유를 구별하기가 어려우므로, PVA-ECC의 섬유분산성 평가를 하기에는 어려운 점이 있다. 이 연구에서는 이러한 문제점을 해결하기 위하여 PVA-ECC 내의 섬유분산성을 평가할 수 있는 새로운 방법을 제시하였다. 형광의 원리를 이용하여 섬유복합재료 단면에서 PVA 섬유가 초록빛을 발하는 이미지를 얻었고, PVA-ECC 시편에 대한 섬유분산성은 형광 현미경에 부착된 CCD (charge coupled device) 카메라를 통하여 얻어진 이미지를 이미지 프로세싱 기법과 통계적인 방법을 이용하여 평가하였다. 또한 형상분석을 통하여 섬유의 방향성이 분산성에 미치는 영향을 파악하였으며, 판별함수기법과 분수령 알고리즘을 이용하여 섬유 검출 성능을 향상시킬 수 있는 기법을 제시하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.33-36
• /
• 2011

Recently, It has increased to use ultra high strength concrete. It is effective to mix organic fibers for preventing spalling. But if fiber mixed, flowability of concrete is decreases. The aim of this study is to evaluation of fire resistance performance for fiber-mixed ultra high strength concrete on field application. As a result, flowability of nylon fiber mixed concrete is better than polyethylene fiber mixed. In non-fiber and polyethylene fiber mixed concrete, spalling occurred. And strain converged at 0.004. Also, residual strength could not evaluate. Nylon fiber mixed concrete is effective to prevent spalling. And it remians 50% residual strength compare with compressive strength at room temperature.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.199-202
• /
• 2002

Interfacial properties and electrical sensing for fiber fracture in carbon and SiC fibers/epoxy composites were investigated by the electrical resistance measurement and fragmentation test. As fiber-embedded angle increased, interfacial shear strength (IFSS) of two-type fiber composites decreased, and the elapsed time was long to the infinity in electrical resistivity. The initial slope of electrical resistivity increased rapidly to the infinity at higher angle, whereas electrical resistivity increased gradually at small angle. Furthermore, both fiber composites with small embedded angle showed a fully-developed stress whitening pattern, whereas both composites with higher embedded angle exhibited a less developed stress whitening pattern. As embedded angle decreased, the gap between the fragments increased and the debonded length was wider for both fiber composites. Electro-micromechanical technique can be a feasible nondestructive evaluation to measure interfacial sensing properties depending on the fiber-embedded angle in conductive fiber reinforced composites.

• 한국안전학회지
• /
• 제13권2호
• /
• pp.122-129
• /
• 1998

A field experiment was performed to analyze the properties of SFRS(steel fiber reinforced shotcrete) against WMRS(wire mesh reinforced shotcrete) with some experimental parameters. The parameters were reinforcing methods(steel fiber and wire mesh), steel fiber contents(0.5%, 0.75%, and 1.0%), silica fume contents(0.0% and 10.0%), spraying thicknesses of layer(10㎝, 8㎝, and 6㎝), and spraying parts(side wall, shoulder, and crown). According to the analyzed results, the mechanical properties of SFRS such as compressive strength, flexural strength, and load-carrying capacity after cracks were improved. And the economic evaluation was also performed on the basis of the required thickness of the layer and other researcher's results for rebound ratios. From the results of this tests, it is found that the traditional WMRS may be substituted by the SFRS in the viewpoint of the economic evaluation as well as the mechanical properties. In additions, the silica fume, even if it is very expensive, can significantly improve the mechanical properties of the shotcrete regardless of mixing with or without the steel fiber.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.125-128
• /
• 2005

Recently new materials, such as fiber reinforced polymer(FRP) and other composite materials are being applied in reinforcing plate or plate or prestressing cables of concrete structures. Although these new materials themselves show the excellent durability and high strength, the bond behaviour between concrete surface and FRP is not well recognized. Therefore, this paper propose a evaluation method for effective bond length between fiber reinforced polymer(FRP) and concrete. To develop the evaluation method, this paper presents a review of current evaluation methods for effective bond length. These methods are compared by single face test, expose merits and demerits. And based on them, new evaluation method was developed. Finally, the new method was compared with existing methods to verify a adequateness for evaluation of effective bond length.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.242-245
• /
• 2000

The fiber contributes the high strength and modulus to the composite. The fiber orientation in FRP has a great effect on the strength of FRP because the strength of FRP mainly depends on the strength of fiber. In this study, FRP was made unidirectionally by pultrusion method and outer part of FRP was made by filament winding method to give fiber orientation to the FRP. The bending strength and bending stresses of FRP rods were simulated according to the winding orientation of glass fiber. The bending strength of FRP was also evaluated. The results of simulation and evaluation Were compared each other to investigate main stresses which affect the fracture of FRP. The main stresses which had a great effect on the strength of FRP were shear stresses.

• Composites Research
• /
• 제12권2호
• /
• pp.10-25
• /
• 1999

Fragmentation 시험법에 의한 섬유상 복합재료의 계면적 특성에 대한 새로운 평가방법이, 순차적으로 섬유간의 간격이 변하게 된 단계적 다섬유 복합재료를 사용하여 제시되었다. 섬유간의 간격이 증가함에 따라, 부서진 섬유들의 형상비는 감소하였으며, 섬유와 기지간의 계면전단강도는 증가함을 보여주었다. 섬유간 거리의 역수를 취했을 때에, 형상비와 계면전단강도 모두가 포화되는 값을 보여주었다. 이것은 단계적 다섬유 복합재료가 형상비에서의 상한값을 나타내고, 계면전단강도에서 하한값을 보여준다는 것을 의미한다. 이 fragmentation 시험법은 복합재료의 평가에 새로운 방법이 될 수 있다. 왜냐하면, 이 두 한계값의 차이를 줄이는 것이 복합재료의 강화에 효과적이기 때문이다. 또한, 섬유 파괴점 부근에서의 섬유응력 분포와 위의 결과를 관련시키기 위해 탄송-소성 유한요소 해석이 행해졌다. 단계적 다섬유 복합재료 시험에서 얻어진 한계값은 그룹형태의 다 섬유 파괴에 의해 야기된 응력집중과 밀접하게 관련되어 있다는 것이 입증되었다.