• Structural Engineering and Mechanics
• /
• v.61 no.6
• /
• pp.711-719
• /
• 2017

This study investigates the effects of reinforcing bar diameter and cover depth on the shrinkage behavior of restrained ultra-high-performance fiber-reinforced concrete (UHPFRC) slabs. For this, twelve large-sized UHPFRC slabs with three different rebar diameters ($d_b=9.5$, 15.9, and 22.2 mm) and four different cover depths (h=5, 10, 20, and 30 mm) were fabricated. In addition, a large-sized UHPFRC slab without steel rebar was fabricated for evaluating degree of restraint. Test results revealed that the uses of steel rebar with a large diameter, leading to a larger reinforcement ratio, and a low cover depth are unfavorable regarding the restrained shrinkage performance of UHPFRC slabs, since a larger rebar diameter and a lower cover depth result in a higher degree of restraint. The shrinkage strain near the exposed surface was high because of water evaporation. However, below a depth of 18 mm, the shrinkage strain was seldom influenced by the cover depth; this was because of the very dense microstructure of UHPFRC. Finally, owing to their superior tensile strength, all UHPFRC slabs with steel rebars tested in this study showed no shrinkage cracks until 30 days.

• Journal of the Korean Geosynthetics Society
• /
• v.2 no.1
• /
• pp.47-55
• /
• 2003

The effects of fiber composition factors of 14 geotextiles which are thickness, porosity, fiber length and diameter etc. on the transmissivity were examined and in-plane permeability of geotextiles under thickness change, transmissivity, confined load were analyzed by the constitutive equations. And the effects of laminar structure on the permittivity of laminar geotextile composites which were manufactured with fiber packing densities were assessed. Transmissivities were increased with thickness of geotextiles and in-plane permeability coefficients were increased with porosity and fiber diameter. The effects of porosity were decreased with normal stress and slightly increased with fiber length. Transmissivities were increased with fiber diameter and showed same tendensy for the same fiber length. Permittivities of laminar geotextile composites were influenced by the waterhead loss in the inner interface and the connection shape of these composites to water path was interpreted as bell mouth type or soft flux pipe type.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.04a
• /
• pp.161-163
• /
• 2001

• Carbon letters
• /
• v.3 no.1
• /
• pp.33-38
• /
• 2002

Petroleum based isotropic pitch was spun into short fiber by melt-blown spinning technology. The processing parameters chosen were air velocity, die temperature, and throughput rate of the pitch within the ranges of experimental tolerances. The fiber diameter was reduced to $6{\mu}m$ by increases of hot air velocity, and spin die temperature. Also, the fiber diameter was strongly dependent on the throughput rate of the pitch and jet speed of hot air through the spinnerets. Even fibers with $10{\mu}m$ diameter were produced at throughput rate of $0.17g/min{\cdot}hole$ and at die temperature of $290^{\circ}C$.

• Membrane Journal
• /
• v.7 no.2
• /
• pp.84-94
• /
• 1997

The performances of both module sets made by different methods for helical module were compared. All experiments were conducted simultaneously at the same transmembrane pressure and energy cosumption per membrane area. The effects of Dean vortices for reducing concentration polarization and fouling were low for the first module set. The increase of 115% for permeate flux improvement(permeate flux difference ${\times}100$/pemeate flux of linear module) was measured. The second module set was more effective in reducing concentration polarization and fouling.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.3-6
• /
• 2003

In this work, poly(ethylene oxide) nanofibers were fabricated by electrospinning to prepare nanofibers-reinforced composites. And the PEO powders-impregnated composites were also prepared to compare with physicochemical properties of nanofibers-reinforced composites. Morphology and fiber diameter of PEO nanofibers were determined by SEM observation. Mechanical interfacial properties of the composites were investigated in fracture toughness tests and interlaminar shear strength (ILSS) test. As a result, the fiber diameter decreased in increasing applied voltage. However the optimum condition for the fiber formation was 15 ㎸, resulting from increasing of jet instability at high voltage and the prepared PEO nanofibers were useful in fiber reinforced composites. The PEO-based nanofibers-reinforced composites showed an improvement of fracture toughness factors ($K_{IC} and G_{ IC}$) and ILSS, compared to the composites impregnated with PEO powders. These results were noted that the nanofibers had higher specific surface area and larger aspect ratio than those of the powder, which played an important role in improving the mechanical interfacial properties of the composites.

• Textile Coloration and Finishing
• /
• v.21 no.6
• /
• pp.22-28
• /
• 2009

Oil-absorbable nonwovens were produced by melt-blown processing of polypropylene chips. The melt-blown processing conditions, such as air pressure, and gear pump speed, DCD. In this study, these three factors were chosen to produce samples. Experimental array and variance analysis of the design of experiment were used to increase the field repeatability and universality. The effect of the factors on oil absorption properties of melt-blown nonwoven fabric such as oil absorbency were evaluated. As a result, the fiber diameter decreased as gearpump speed decreased or air pressure increased. The oil absorbency increased as air pressure increased or gearpump speed decreased and with the DCD increasing the oil absorbency significantly increased.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.2
• /
• pp.186-190
• /
• 2015

$TiO_2$ nanoparticles can be used to improve the performance of carbon fiber-reinforced epoxy resin composites. In this study, the effect of the size of $TiO_2$ nanoparticles on the mechanical properties of carbon fiber-reinforced epoxy resin composites was investigated. The size of the $TiO_2$ nanoparticles was easily controlled using heat treatment. The size of the $TiO_2$ nanoparticles for this study were20nm, 100nm, and 200nm. Three types of carbon fibers with different diameters were also used in this study. The carbon fiber-reinforced epoxy resin composites with 20-nm $TiO_2$ powder showed the highest tensile strength compared to the other types of CFRP, regardless of the fiber maker or fiber diameter. The size of the $TiO_2$ powder and the diameter of the carbon fiber strongly affected the interfacial properties of all kinds of CFRP in this study.

• Physical Therapy Korea
• /
• v.7 no.3
• /
• pp.34-48
• /
• 2000

The purpose of this study was to determine the effects of mild-intensity exercise training on the denervated muscle atrophy in the sciatic nerve injured rat. Thirty-six male Sprague-Dawley rats (250~300 g) were randomly assigned into three groups; sham-denervated group (n=8), denervated group (n=8), and denervated-exercised group (n=20). Exercise consisted of treadmill running at 20 m/min speed with 0% grade for 30 min/day. The animals were decapitated at the second and sixth weeks postcrush. Soleus and medial gastrocnemius were immediately excised to be weighed. Type I and II fibers of the muscles were differentiated by m-ATPase (pH 9.4) stain, and fiber diameters were evaluated. The results were as follows: 1) The weight of the soleus and medial gastrocnemius muscles showed a tendency to increase in both the denervation-exercised groups compared to the denervated group. 2) In the 2-week denervation-exercised group, type II fiber diameter of soleus and type I fiber diameter of medial gastrocnemius were increased significantly compared to the denervated control group. 3) In the 6-week denervated-exercised group, type I fiber diameter of soleus and type II fiber diameter of medial gastrocnemius were hypertrophied significantly compared to sham-denervated group. The results of this study suggested that treadmill exercise partially prevented denervation atrophy in the soleus and medial gastrocnemius of the rat.

• Journal of the Korea Furniture Society
• /
• v.29 no.1
• /
• pp.1-7
• /
• 2018

A study was carried out to observe the 1% aqueous safranine solution flow speed in longitudinal and radial directions of softwood Metasequoia glyptostroboides, diffuse-porous wood Anthocephalus cadamba and ring-porouswood Fraxinus rhynchophylla. In radial direction, ray cells and in longitudinal direction, tracheids, vessel and wood fiber were considered for the measurement of liquid penetration speed at less than 12% moisture contents (MC). The length, lumen diameter, pit diameter, end wall pit diameter and the numbers of end wall pits determined for the flow rate. The liquid flow in the those cells was captured via video and the capillary flow rate in the ones were measured. Vessel in hardwood species and tracheids in softwood was found to facilitate prime role in longitudinal penetration. Anatomical features like the length and diameter, end-wall pit numbers of ray parenchyma were found also responsible fluid flow differences. On the other hand, vessel and fiber structure affected the longitudinal flow of liquids. Therefore, the average liquid penetration depth in longitudinal tracheids of Metasequoia glyptostroboides was found the highest among all cells considered in Anthocephalus cadamba and Fraxinus rhynchophylla In radial direction, ray parenchyma of Metasequoia glyptostroboides was found the highest depth and the one of Fraxinus rhynchophylla was the lowest. The solution was penetrated lowest depth in the wood fiber of Fraxinus rhynchophylla. The large vessel of Fraxinus rhynchophylla was found the lowest depth among the vessels. The solutin was penetrated to the wood fiber of Anthocephalus cadamba higher than the one of Fraxinus rhynchophylla.