• Resources Recycling
• /
• v.24 no.5
• /
• pp.33-39
• /
• 2015

A basic study was conducted to effectively recover nitric acid from a waste solder stripper by diffusion dialysis using anion exchange membranes. The effects of flow rate, flux ratio, nitrate concentration, and metallic ion types and concentration on the recovery percentage of nitric acid were investigated. The recovery percentage of nitric acid was decreased with the increase of flow velocity. But the recovery percentage of nitric acid was increased as the increase of flux ratio(W/F) and showing a recovery percentage of nitric acid of about 99% at a flux ratio of 1.5 or more. As the increase of nitric acid concentration in feed solution, the recovery percentage of nitric acid was increased up to 3.0M, but in case of greater than 3.0M, the recovery percentage gradually was decreased. Leakage percentage of metallic ions through the membrane were in the order of Pb, Na and Cu but Fe and Sn did not leakaged. As a result of diffusion dialysis using real waste solder stripper at a flow rate of $0.9L/hr-m^2$, W/F = 1.3, a recovery percentage of nitric acid of approximately 94% was gained.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.320-332
• /
• 2013

The feed air to MSW incinerator influences on the residence time of combustion gas, removal of unburnt ash and exiting gas temperature. Thus the secondary air volume could present sufficient residence time which can maintain the exiting temperature over $850^{\circ}C$. The secondary air also relates directly with the turbulence in the inside of combustion chamber, which finally provide the stable combustion condition. The present study designed a modern incinerator for a field scale, and evaluation of the potential amount of primary air based on the daily combustible quantity. From the evaluated primary air volume, the secondary air flow rate could be estimated, and its dynamic behavior was verified. In addition, the obtained air volume enables to find an optimum operation condition of the combustion. As a result of the CFD simulation, the air ratio 75 : 25 between primary and secondary air amount was optimum ratio than design criteria 72 : 28. And the flow velocity ratio of front-back of secondary air jet nozzle was found excellent at 1 : 3. In addition, the result of applied to the plant, the removal efficiency of NOx and CO generation would concentration of CO.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.1
• /
• pp.127-131
• /
• 2020

Objective: This study was conducted to determine catalytic properties of wheat phytase with exopolyphosphatase activity toward medium-chain and long-chain inorganic polyphosphate (polyP) substrates for comparative purpose. Methods: Exopolyphosphatase assay of wheat phytase toward polyP75 (medium-chain polyP with average 75 phosphate residues) and polyP1150 (long-chain polyP with average 1150 phosphate residues) was performed at pH 5.2 and pH 7.5. Its activity toward these substrates was investigated in the presence of Mg²⁺, Ni²⁺, Co²⁺, Mn²⁺, or ethylenediaminetetraacetic acid (EDTA). Michaelis constant (K_m) and maximum reaction velocity (V_max) were determined from Lineweaver-Burk plot with polyP75 or polyP1150. Monophosphate esterase activity toward p-nitrophenyl phosphate (pNPP) was assayed in the presence of polyP75 or polyP1150. Results: Wheat phytase dephosphorylated polyP75 and polyP1150 at pH 7.5 more effectively than that at pH 5.2. Its exopolyphosphatase activity toward polyP75 at pH 5.2 was 1.4-fold higher than that toward polyP1150 whereas its activity toward polyP75 at pH 7.5 was 1.4-fold lower than that toward polyP1150. Regarding enzyme kinetics, K_m for polyP75 was 1.4-fold lower than that for polyP1150 while V_max for polyP1150 was 2-fold higher than that for polyP75. The presence of Mg²⁺, Ni²⁺, Co²⁺, Mn²⁺, or EDTA (1 or 5 mM) exhibited no inhibitory effect on its activity toward polyP75. Its activity toward polyP1150 was inhibited by 1 mM of Ni²⁺ or Co²⁺ and 5 mM of Ni²⁺, Co²⁺, or Mg²⁺. Ni²⁺ inhibited its activity toward polyP1150 the most strongly among tested additives. Both polyP75 and polyP1150 inhibited the monophosphate esterase activity of wheat phytase toward pNPP in a dose-dependent manner. Conclusion: Wheat phytase with an unexpected exopolyphosphatase activity has potential as a therapeutic tool and a next-generational feed additive for controlling long-chain polyP-induced inappropriate inflammation from Campylobacter jejuni and Salmonella typhimurium infection in public health and animal husbandry.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.21 no.2
• /
• pp.63-70
• /
• 2013

Experiments in a pilot-scale hybrid multi-stage unit system (HMUS) combination of ATAD and EGSB followed by SBR process for pig slurry treatment were conducted to demonstrate the feasibility of using autothermal thermophilic aerobic digestion (ATAD) and expended granular sludge bed (EGSB) followed by sequencing batch reactor (SBR) system. Contaminants in pig slurry with high organic matter, nitrogen (N) and phosphorus (P) content were completely removed in the combined process. The highest removal rate for CODcr among contaminants in the feed pig slurry was attained by about 43.3% in ATAD unit process. Also TS removal rate of 96.5% was attained and the highest in the next coagulation unit process. The highest removal rate of CODcr under operating parameter conditions of OLR(organic loading rate), 3-6Kg $COD/m^3{\cdot}day$ and line velocity, 1.5-4m/h was earned at 3days of HRT. The disinfection of pathogens was effective at 50,000mg/L of TS in ATAD unit process. Biogas production per organic removal was $2.3{\sim}8.5m^3/kgTS{\cdot}d$ (average $5.2m^3/kgTS{\cdot}d$) in EGSB unit process. The average removal rates of CODcr 71.7%, TS 64.1%, TN 45.9%, and TP 50.4% were earned in the intermittent aeration SBR unit process.

• Journal of Korea Soil Environment Society
• /
• v.4 no.2
• /
• pp.137-147
• /
• 1999

Fluidized-bed thermal desorber coupled with a heat pipe was investigated for the remediation of soil contaminated with diesel oils. Thermal gravimetric analysis by Cahn-balance indicated that the desorption of diesel oils from the soil particles was mainly governed by the internal diffusion at low concentration of less than 0.5 wt. % of oils in the soil particles. In fluidized-bed experiments. increase of fluidizing gas velocity reduced the residual oils of the contaminated soils, the increase of soil feed rate decreased efficiency of fluidized-bed desorber. A mathematical model was developed by incorporating Fickian diffusion kinetics into the Kunii-Levenspiel model Simulation results showed reasonable agreement for the performance of fluidized-bed thermal desorber.

• Journal of Environmental Science International
• /
• v.23 no.10
• /
• pp.1703-1718
• /
• 2014

An eco-friendly integrated multi-trophic aquaculture (IMTA) farming technique was developed with the goal of resolving eutrophication by excess feed and feces as fish-farming by-products. A variety of seaweed species were tried to remove inorganic nutrients produced by fish farming. However, there have been few trials to use Sargassum fulvellum in an IMTA system, a species with a relatively wide distribution across regions with various habitat conditions, great nutrient removal efficiency and importance for human food source and industrial purposes. In this regard, our study tried to examine feasibility of using S. fulvellum in an IMTA system by analyzing growth characteristics of the species in an IMTA system comprising of rockfish (Sebastes shlegeli), sea cucumber (Stichopus japonocus) and the tried S. fulvellum (October 2011 - November 2012). We also monitored environment conditions around the system including current speed, water temperature and inorganic nutrient level as they may affect growth of S. fulvellum. S. fulvellum in the IMTA system, which were $15.72{\pm}5.67mm$ long at the start of the experiment in October 2011, grew to a maximum of $1093{\pm}271.13mm$ by May 2012. In September, seaweed growth was reduced to a minimum of $280{\pm}70.43mm$ in length. Then, S. fulvellum began to grow again reaching $325{\pm}196.19mm$ by November 2012. Wet weight of the seaweed was $4.01{\pm}1.89g$ at the start of the experiment and reached a maximum of $109.26{\pm}34.23g$ in May. The weight gradually declined to a low of $15.12{\pm}8.40g$ in September 2012. Weight began to increase once more, rising to $39.27{\pm}21.69g$ by November. During the experiment, the average velocity at the surface and the bottom was 6.5 cm/s and 3.4 cm/s, respectively. The water temperature ranged $5.0-23.5^{\circ}C$, which was considered suitable for growing S. fulvellum. Results of the study indicated no significant differences in inorganic nutrients between pre- and post-IMTA installation. It was thus concluded that S. fulvellum can be a suitable seaweed species to be used in an IMTA system.

• Korean Journal of Environment and Ecology
• /
• v.30 no.5
• /
• pp.888-895
• /
• 2016

The population ecology (Ecological characteristics) of Squalidus chankaensis tsuchigae were investigated at Geum River from March to November, 2013. This species inhabited midstream of the river where was mostly covered with cobble and sand. The depth of the habitat was 30~60 cm and velocity of stream was 2.27~4.88 cm/sec. The sex ratio of female to male was 1 : 0.86. They were sexually mature when they were over two years of age. The spawning period was from June to July with water temperatures from $25^{\circ}C$ to $25^{\circ}C$. Sexually matured individuals appeared over the two year of age. Frequency analysis of total length indicated that the group with 55~70 mm in total length was one year old, the 71~90 mm was two years old, and the group over 91 mm was three years old. The average number of eggs in the ovaries was estimated as 2,219 per matured female. The number of matured eggs size in ovaries was 0.64~0.98 (mean: 0.85) mm. Calulation length-weight relation of S. chankaensis tsuchigae show the value of contant a as 0.0002 and b as 2.81, and condition factor (K) was 1.06 on average. The stomach contents were Cyanophyta, Chlorophyta, Bacillariophyta, Crustaceae, Copepoda, Nematota, Actithocephala, and Ephemeroptera, Hemiptera, Diptera, and Trichoptera that belong to Aquatic insect, and dormant bud of Pectinatella that belongs to Phylactolaemata. The diet of S. chankaensis tsuchigae was omnivorous, mainly vegetable feed on attached algae (filament form), and mainly animality feeded on benthic invertebrates such as Chironomidae larvae.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.4
• /
• pp.179-189
• /
• 2006

High velocity oxygen fuel(HVOF) thermal spray coating of WC-Co powder is one of the most promising candidate for the replacement of the traditional hard chrome plating and ceramics coating because of the environmental problem of the very toxic $Cr^{6+}$ known as carcinogen and the brittleness of ceramics coating. WC-Co micron and nano powder were coated by HVOF thermal spraying method for the study of durability improvement of the high speed spindle. Coatings were planned by Taguchi program for the four spray parameters of spray distance, flow rates of hydrogen, oxygen and powder feed rate. Optimal coating process was obtained by the studies of coating properties such as porosity, surface roughness, micro hardness, and micro structure. WC-Co micron and nano powder were coated on the Inconel 718 substrate by the optimal coating process obtained in this study. The wear behaviors were studied by the sliding wear tester at room temperature and at an elevated temperature of $500^{\circ}C$ for the application to high speed spindle. Sliding wear test was carried out for four most promising hard coatings of chrome coating, ceramics coatings such as $A1_2O_3,\;Cr_2O_3$ and HVOF Co-alloy T800 for the comparison of their wear behaviors. HVOF WC-Co coating was better than other coatings showing highest micro hardness of 1400 Hv and comparable friction coefficients with others. HVOF WC-Co coating is a strong candidate for the replacement of the traditional hard chrome plating for the high speed spindle.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.17-24
• /
• 2021

The development of a new sorbent for carbon dioxide depends on several factors, such as fast adsorption/absorption velocity, hydrophobicity, and lower regeneration temperature than commercial sorbent. In this study, aminosilane grafted activated carbon was synthesized to capture CO2. Methyltrimethoxysilane (MTMS) and 3-aminopropyl-triethoxysilane (APTES) were used as the grafting precursor of the amine functional group. The APTES grafting activated carbon showed higher sorption property than MTMS used one. The characteristics of the separation mechanism of carbon dioxide were examined by measuring the adsorption capacity according to temperature and carbon dioxide partial pressure. The absorption capacity of carbon dioxide was similar to amine grafting activated carbon and activated carbon at 25℃, but amine-grafted activated carbon was higher at 75℃. The amine functional group-grafted activated carbon showed higher absorption capacity than activated carbon with a 1% carbon dioxide partial pressure. Aminosilane grafting of activated carbon was chemically absorbed but also showed the characteristics of physical adsorption. The reforming activated carbon with an amine functional group grafted solid absorption/adsorption sorbent would significantly impact the material engineering industry and carbon dioxide adsorption process. The functionalized sorbent is a high-performance composite material. The developed sorbent may have applications in other industrial processes of absorption/adsorption and separation.

• Journal of The Korean Astronomical Society
• /
• v.56 no.2
• /
• pp.169-185
• /
• 2023

The GMT-Consortium Large Earth Finder (G-CLEF) is the first instrument for the Giant Magellan Telescope (GMT). G-CLEF is a fiber feed, optical band echelle spectrograph that is capable of extremely precise radial velocity measurement. G-CLEF Flexure Control Camera (FCC) is included as a part in G-CLEF Front End Assembly (GCFEA), which monitors the field images focused on a fiber mirror to control the flexure and the focus errors within GCFEA. FCC consists of an optical bench on which five optical components are installed. The order of the optical train is: a collimator, neutral density filters, a focus analyzer, a reimager and a detector (Andor iKon-L 936 CCD camera). The collimator consists of a triplet lens and receives the beam reflected by a fiber mirror. The neutral density filters make it possible a broad range star brightness as a target or a guide. The focus analyzer is used to measure a focus offset. The reimager focuses the beam from the collimator onto the CCD detector focal plane. The detector module includes a linear translator and a field de-rotator. We performed thermoelastic stress analysis for lenses and their mounts to confirm the physical safety of the lens materials. We also conducted the global structure analysis for various gravitational orientations to verify the image stability requirement during the operation of the telescope and the instrument. In this article, we present the opto-mechanical detailed design of G-CLEF FCC and describe the consequence of the numerical finite element analyses for the design.