• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.501-509
• /
• 2016

We propose a method to improve the robustness of speaker verification on short test utterances. The accuracy of the state-of-the-art i-vector/probabilistic linear discriminant analysis systems can be degraded when testing utterance durations are short. The proposed method compensates for utterance variations of short test feature vectors using deep neural networks. We design three different types of DNN (Deep Neural Network) structures which are trained with different target output vectors. Each DNN is trained to minimize the discrepancy between the feed-forwarded output of a given short utterance feature and its original long utterance feature. We use short 2-10 s condition of the NIST (National Institute of Standards Technology, U.S.) 2008 SRE (Speaker Recognition Evaluation) corpus to evaluate the method. The experimental results show that the proposed method reduces the minimum detection cost relative to the baseline system.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.13 no.4
• /
• pp.2471-2478
• /
• 1971

Go Cong Water Control Project was conducted on its preliminary survey and design by Agricultural development Corporation for the Korean Government, an Executing Agency, and Directorate of Irrigation and Rural Engineering of the Ministry of Land Reform, Agriculture and Fishery Development for the Vietnamese Government, a cooperation Agency, under Korean and Vietnamese Economic and Technical Cooperation Program. The main purposes of the project are aimed at the improvements of irrigation and drainage, and salt water prevention of the Go Cong area located at northern part of the Mekong Delta. All the works from field survey through design to preparing reports were carried out by ADC alone and recently Korean Government submitted the relevant reports to vietnamese Government through official channel. The contents of the project are summarized as following: 1. The project comprises irrigation, drainage and salt water prevention facilities on the benefited area of about 55,000 hectares, covering Go Cong and Dinh Tuong(My Tho) Provinces and it will be possible to cultivate rice cropping twice a year, irrigating all the area in the dry season; 2. With completion of this project, annual production of rough rice and vegetables are anticipated to increase by 222,600 .T. and 142,600 M.T. respectively and the internal rateof return stants at 26 per cent, applying for the exchange rate of US $ 1 to VN $ 275. 3. Total investments required for the project are estimated at US $ 56,394,000 of which actual construction cost is estimated at US $ 39,183,000. The project has planned to be d to be developed by four stages, taking bout 7 years. 4. The project needs for three places of pumping plants. 57Km of feed and main irrigation canals, 81Km of drainage channels, 97Km of dike, 23 places of sluices and navigation locks, etc.

• Journal of Korea Multimedia Society
• /
• v.11 no.4
• /
• pp.516-524
• /
• 2008

This paper presents a new modeling technique for the simulation of cloth specific characteristics with a set of hard constraints using an implicit constraint enforcement scheme. A conventional explicit Baumgarte constraint stabilization method has several defects. It requires users to pick problem-dependent coefficients to achieve fast convergence and has inherent stabilization limits. The proposed implicit constraint enforcement method is stable with large time steps, does not require problem dependent feed-back parameters, and guarantees the natural physics-based motion of an object. In addition, its computational complexity is the same as the explicit Baumgarte method. This paper describes a formulation of implicit constraint enforcement and provides a constraint error analysis. The modeling technique for complex components of cloth such as seams, buttons, sharp creases, wrinkles, and prevention of excessive elongation are explained. Combined with an adaptive constraint activation scheme, the results using the proposed method show the substantial enhancement of the realism of cloth simulations with a corresponding savings in computational cost.

• Journal of Sericultural and Entomological Science
• /
• v.50 no.2
• /
• pp.112-115
• /
• 2012

To develop an efficient mass rearing system for Cadra cautella(Walker) and Orius laevigatus(Fieber) were investigated under the conditions of photoperiod 16L : 8D, $70{\pm}5%$ RH and $23{\pm}2^{\circ}C$. The highest efficiency rate(multiply 28.6) of C. cautella was achieved when using the rearing cage of $20{\ell}$ than $3{\ell}$. The highest efficiency rate(multiply 16.3) of O. laevigatus was achieved when using the rearing cage of $5{\ell}$ (adult 1,500, 10 pcs(10 cm) of plant of egg taking). The moth could be successfully reared with all food substrates tested, of which rice bran(43%) + chick feed(43%) + yeast(14%) assumed to be proper for mass-rearing in view of cost.

• Journal of Animal Science and Technology
• /
• v.63 no.5
• /
• pp.1064-1075
• /
• 2021

Recently, a high level of dietary crude protein (CP) has become of interest as a possible practice to improve the carcass quality of beef cattle, and its level has been increasing in the field. However, there is little scientific evidence that supports this. This study was conducted to test whether a high dietary CP level would improve growth performance, body metabolism, and carcass traits in Hanwoo beef cattle. A total of 32 Hanwoo finishing beef cattle (18 multiparous cows, six heifers, and eight steers) participated in a 12-weeks feeding trial. Two kinds of total mixed rations were prepared to contain two different CP; 156 g/kg for the control (CON) and 173 g/kg of CP for the treatment (HCP), while maintaining a similar level of metabolizable energy. The experiment was ended when more than half of the steers reached the target body weight (730 kg). Blood was collected at the end of the experiment. After harvesting, the carcass trait was evaluated at the slaughterhouse according to Korean standards. The carcass yield score and grade were also calculated based on revised criteria. Overall, dry matter intake, average daily gain, blood metabolites concentration, and the carcass traits, except for backfat thickness and the yield score, did not differ between the treatments. The HCP had lower backfat thickness than those of CON. There was no difference in the carcass yield grade, but the yield score was higher in the HCP treatment. According to the newly revised carcass grading criteria, both yield score and grade were higher in HCP than in CON. Increasing CP supply decreased the carcass's backfat thickness without altering growth performance and body metabolism, resulting in improved yield score and grade. Therefore, feeding a high CP diet may be beneficial in the farm income, although it may also increase feed cost and nitrogen excretion to the environment.

• Resources Recycling
• /
• v.28 no.1
• /
• pp.62-72
• /
• 2019

Generally, $H_2SO_4$ and Cu metal are used as raw materials for producing copper sulfate. The study relates to a method for producing copper sulfate using electrowinning from a waste solution of copper chloride. Uses are used for copper plating for industry, plating, feed, agriculture, electronic grade PCB. Conventional methods for producing copper sulfate have a problem of a large amount of waste water and a high energy cost. A study on the production method of copper sulfate ($CuSO_4$), which is the most used among copper (Cu) compounds, has a low process operation ratio, a small amount of waste water, and a simple manufacturing process. It is easy to remove Na, Ca, Mg, and Al as impurities by using a cationic membrane. At the same time, high purity copper powder could be recovered by an electrowinninng method. Using the recovered copper powder, high purity copper sulfate could be produced.

• Korean Journal of Poultry Science
• /
• v.46 no.1
• /
• pp.47-53
• /
• 2019

The aim of this study was to investigate the difficulties that Korean farmers and processors currently experience with respect to the market for Korean native chicken (KNC). This study also provides suggestions by which they can overcome these difficulties. In all, sixty-nine farmers and sixty-two processors participated in our investigation, which addressed 1) the current difficulties that KNC farmers face, 2) the current importance-satisfaction measures among KNC farmers and processors, and 3) the future direction of the KNC market: farmer and processor opinions. The respondents stated that the limited number of sales stores was the most difficult market condition they faced in raising KNC, followed by feed cost, animal disease, and poor production environment. Regarding issues of importance and satisfaction, origin in raising step and slaughtering in the processing and distribution step were considered the areas most in urgent need of improvement, given farmers' and processors' high levels of dissatisfaction with these. Both the free-range farming system and the concept of animal welfare are growing in importance, given consumers' interests in these areas. As to opinions on the direction of KNC development, menu development was cited as most important, followed by public advertisement, accessibilities, business aid, and breed development. Consequently, the results show that well-organized support from both the government and related industries is needed, as chicken farmers and processors cannot resolve certain limitations inherent in the KNC industry on their own.

• Advances in nano research
• /
• v.10 no.1
• /
• pp.59-69
• /
• 2021

Electrospinning is a cost-effective and versatile method for producing submicron fibers. Although this method is relatively simple, at the theoretical level the interactions between process parameters and their influence on the fiber morphology are not yet fully understood. In this paper, the aim was finding optimal electrospinning parameters in order to obtain the smallest fiber diameter by using Taguchi's methodology. The nanofibers produced by electrospinning a solution of Thermoplastic Polyurethane (TPU) in Dimethylformamide (DMF). Polymer concentration and process parameters were considered as the effective factors. Taguchi's L9 orthogonal design (4 parameters, 3 levels) was applied to the experiential design. Optimal electrospinning conditions were determined using the signal-to-noise (S/N) ratio with Minitab 17 software. The morphology of the nanofibers was studied by a Scanning Electron Microscope (SEM). Thereafter, a tensile tester machine was used to assess mechanical properties of nanofibrous scaffolds. The analysis of DoE experiments showed that TPU concentration was the most significant parameter. An optimum combination to reach smallest diameters was yielded at 12 wt% polymer concentration, 16 kV of the supply voltage, 0.1 ml/h feed rate and 15 cm tip-to-distance. An empirical model was extracted and verified using confirmation test. The average diameter of nanofibers at the optimum conditions was in the range of 242.10 to 257.92 nm at a confidence level 95% which was in close agreement with the predicted value by the Taguchi technique. Also, the mechanical properties increased with decreasing fibers diameter. This study demonstrated Taguchi method was successfully applied to the optimization of electrospinning conditions for TPU nanofibers and the presented scaffold can mimic the structure of Extracellular Matrix (ECM).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.54 no.6
• /
• pp.974-981
• /
• 2021

The aim of this study was to evaluate genetic parameters of growth traits for improving selective breeding in olive flounder Paralichthys olivaceus produced in April 2019. The total length and body weight at 11-, 18-, and 22-months-old were measured for 7,479, 2,831 and 1,904 individuals, respectively. Since 2004, we have been conducting a selective breeding program to improve growth traits in the olive flounder. Data were analyzed using the restricted maximum likelihood method using the multiple traits animal model. The effect of sex and production period showed significant differences in all traits (P<0.05). The heritability of all traits was 0.428-0.520, which is relatively high by measurement month. Therefore, it is considered that individual selection will be more advantageous than family selection. However, to maintain an appropriate degree of inbreeding and genetic diversity for future generations, it is necessary to consider family selection adequately. Results of the correlation analysis between the same traits according to the measurement period indicated that considering production costs such as feed cost, selection at 18-months-old will be advantageous. Olive flounder is a major aquaculture species in Korea, and continuous selective breeding research is essential to improve productivity.

• Structural Engineering and Mechanics
• /
• v.80 no.5
• /
• pp.503-522
• /
• 2021

This paper investigates experimentally and numerically the influence of drilling process on the mechanical and thermomechanical behaviors of woven glass fiber reinforced polymer (GFRP) composite plate. Through the experimental analysis, a CNC machine with cemented carbide drill (point angles 𝜙=118° and 6 mm diameter) was used to drill a woven GFRP laminated squared plate with a length of 36.6 mm and different thicknesses. A produced temperature during drilling "heat affected zone (HAZ)" was measured by two different procedures using thermal IR camera and thermocouples. A thrust force and cutting torque were measured by a Kistler 9272 dynamometer. The delamination factors were evaluated by the image processing technique. Finite element model (FEM) has been developed by using LS-Dyna to simulate the drilling processing and validate the thrust force and torque with those obtained by experimental technique. It is found that, the present finite element model has the capability to predict the force and torque efficiently at various drilling conditions. Numerical parametric analysis is presented to illustrate the influences of the speeding up, coefficient of friction, element type, and mass scaling effects on the calculated thrust force, torque and calculation's cost. It is found that, the cutting time can be adjusted by drilling parameters (feed, speed, and specimen thickness) to control the induced temperature and thus, the force, torque and delamination factor in drilling GFRP composites. The delamination of woven GFRP is accompanied with edge chipping, spalling, and uncut fibers.