• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.335-342
• /
• 2016

This paper proposes an energy storage-assisted, series-connected module-integrated power conversion system that integrates a photovoltaic power conditioner and a charge balancing circuit. In conventional methods, a photovoltaic power conditioner and a cell-balancing circuit are needed for photovoltaic systems with energy storage devices, but they cause a complex configuration and high cost. Moreover, an imbalanced output voltage of the module-integrated converter for PV panels can be a result of partial shading. Partial shading can lead to the fault condition of the boost converter in shaded modules and high voltage stresses on the devices in other modules. To overcome these problems, a bidirectional buck-boost converter with an integrated magnetic device operating for a charge-balancing circuit is proposed. The proposed circuit has multiple secondary rectifiers with inductors sharing a single magnetic core, which works as an inductor for the main bidirectional charger/discharger of the energy storage. The secondary rectifiers operate as a cell-balancing circuit for both energy storage and the series-connected multiple outputs of the module-integrated converter. The operating principle of the cell-balancing power conversion circuit and the power stage design are presented and validated by PSIM simulation for analysis. A hardware prototype with equivalent photovoltaic modules is implemented for verification. The results verify that the modularized photovoltaic power conversion system in the output series with an energy storage successfully works with the proposed low-cost bidirectional buck-boost converter comprising a single magnetic device.

• The Journal of Engineering Geology
• /
• v.19 no.3
• /
• pp.287-294
• /
• 2009

To be design the slope, the area distributed the mica schist which was metamorphosed by shale or mudstone must carefully consider the stability. Mica schist is another unstable rock for slope by schistosity, cleavage, axial plane of a fold etc. In general mica schist contains the swelling clay minerals such as smectite, vermiculite and montmorillonite. These minerals make the slope unstable. At OO tunnel construction area for the rail way of the Kyungbu high speed train, the slope of mica schist is very unstable by the distribution phenomena of the discontinuous plane such as joints which are 1-5 cm spacing and thrust and strike-slip fault. By the drilling core of this area, most RQD have 0-20%.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.9
• /
• pp.4023-4043
• /
• 2016

Network virtualization has been regarded as a core attribute of the Future Internet. In a network virtualization environment (NVE), multiple heterogeneous virtual networks can coexist on a shared substrate network. Thus, a substrate network failure may affect multiple virtual networks. In this case, it is increasingly critical to provide survivability for the virtual networks against the substrate network failures. Previous research focused on mechanisms that ensure the resilience of the virtual network. However, the resource efficiency is still important to make the mapping scheme practical. In this paper, we study the survivable virtual network embedding mechanisms against substrate link and node failure from the perspective of improving the resource efficiency. For substrate link survivability, we propose a load-balancing and re-configuration strategy to improve the acceptance ratio and bandwidth utilization ratio. For substrate node survivability, we develop a minimum cost heuristic based on a divided network model and a backup resource cost model, which can both satisfy the location constraints of virtual node and increase the sharing degree of the backup resources. Simulations are conducted to evaluate the performance of the solutions. The proposed load balancing and re-configuration strategy for substrate link survivability outperforms other approaches in terms of acceptance ratio and bandwidth utilization ratio. And the proposed minimum cost heuristic for substrate node survivability gets a good performance in term of acceptance ratio.

• Journal of KIISE:Computer Systems and Theory
• /
• v.35 no.5
• /
• pp.187-198
• /
• 2008

This paper develops a framework for efficient resource management within the grid service environment. Resource management is the core element of the grid service; therefore, GridRMF(Grid Resource Management Framework) is modeled and developed in order to respond to such variable characteristics of resources as accordingly as possible. GridRMF uses the participation level of grid resource as a basis of its hierarchical management. This hierarchical management divides managing domains into two parts: VMS(Virtual Organization Management System) for virtual organization management and RMS(Resource Management System) for metadata management. VMS mediates resources according to optimal virtual organization selection mechanism, and responds to malfunctions of the virtual organization by LRM(Local Resource Manager) automatic recovery mechanism. RMS, on the other hand, responds to load balance and fault by applying resource status monitoring information into adaptive performance-based task allocation algorithm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.830-833
• /
• 2007

In this paper, we implemented a $17{\times}17b$ binary digital multiplier using radix-4 Booth;s algorithmand proposed an efficient testing methodology for the full-custom design. A two-stage pipeline architecture was applied to achieve higher throughput and 4:2 adders were used for regular layout structure in the Wallace tree partition. Several chips were fabricated using LG Semicon 0.6-um 3-Metal N-well CMOS technology. We did fault simulations efficiently using the proposed test method resulting in the reduction of the number of faulty nodes by 88%. The chip contains 9115 transistors and the core area occupies $1135^*1545$ mm2. The functional tests using ATS-2 tester showed that it can operate with 24 MHz clock at 5.0 V at room temperature.

• Economic and Environmental Geology
• /
• v.26 no.4
• /
• pp.519-539
• /
• 1993

A total of 264 independently oriented core samples were collected from 26 sites in the southwestern part (the Naktong Trough) of the Cretaceous $Ky{\check{o}}ngsang$ Basin in south Korea. The sampled formations comprise the sedimentary Shindong and the Hayang Groups of the Lower Cretaceous age. Alternating field and thermal demagnetizations were conducted. Characteristic remanent magnetization (ChRM) was relatively easily isolated in each formation except in the Chinju formation, from which only remagnetization circles were observed. Even though an extensive use of the fold test was not possible due to the nearly homoclinal nature of the strata in the area, we believe that the ChRM of each formation is of primary origin based on the following grounds: The in-situ ChRM direction of each formation is different from the present geomagnetic field direction. Fisherian precision parameter becomes enhanced through the tilt correction in all formations, closely to the values required for a positive fold test. Three out of the five studied formations pass the reversal test. The mean palaeomagnetic pole position from the studied area is found to be statistically different from the contemporary pole from the Chinese block exclusive of the Shandong area. The difference in magnetic declination suggests a $14.5^{\circ}$ (${\pm}10.5^{\circ}$) clockwise rotation of the studied area relative to the Chinese block comprising the west of the Tan-Lu fault. On the other hand, any significant difference in magnetic inclination and concurrent palaeolatitude is not observed between the studied area and China as well as the other area (Taegu-Andong area) in the $Ky{\check{o}}ngsang$ Basin. The dual nature of the magnetic polarity confirmed in all formations suggests an older than 124 Ma (Neocomian or older) age of the studied sedimentary strata.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.288-300
• /
• 2002

In this paper, a novel method of equalization of RF transceivers is suggested for MIMO(Multiple Input Multiple Output) antenna actively studied for high speed data transmission in the recent IMT-2000 system. The core of suggestion is in equalizing the transfer characteristics of multiple transceivers using feedback and memory during the predefined calibration time. This makes it possible to weight the signals in the intermediate frequency, which is easier in the application of recently developed DoA(Direction of Arrival) algorithms. In addition, the time varying optimum cell formation according to traffic is feasible by antenna beam-forming based on the DoA information. The suggested method of equalizing multiple transceivers are successfully verified using envelope simulation. two outputs. This paper is concerned with the diagnosis of multiple crosstalk-faults in OSM. As the network size becomes larger in these days, the convent.
nal diagnosis methods based on tests and simulation be.
me inefficient, or even more impractical. We propose a simple and easily implementable alg？ithm for detection and isolation of the multiple crosstalk-faults in OSM. Specifically, we develop an algorithm for isolation of the source fault in switc.
ng elements whenever the multiple crosstalk-faults are.
etected in OSM. The proposed algorithm is illustrated by an example of 16$\times$16 OSM.

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.2
• /
• pp.339-347
• /
• 1996

object-oriented programming is used to develop next-generation telecommu- nications services running on the distributed processing environment. In order to test these services efficiently at the system-level during not only in the development phase but also in the operation phase, we define an embedded monitor service within the infrastructure to monitor the operation of the distributed programs, and describe a system-level test mechanism based on the monitor service. By separating the function of monitor server which monitors operations of objects and collects monitored data and that of tester which makes analysis and decides the sequence of test events, the invasive effect of monitoring can be minimized. At the same time, accurate diagnosis on the system can be achieve by exploiting the test mechanism. The mechanism, as a core component for the implementation of real-time fault-tol-erant systems, is applicable to general-purpose distributeded systems as well.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.113-117
• /
• 2008

We investigated the current limiting and the recovery characteristics of a flux-lock type superconducting fault current limiter(SFCL) according to the winding directions. The flux-lock type SFCL consists of two coils. The primary coil was wound in parallel to the secondary coil through an Iron core, and the secondary coil was connected with the superconducting element in series. We have changed the winding direction of coils to compare the resistive type SFCL with the flux-lock type SFCL. The current limiting and the recovery characteristics were dependent on the winding direction. The quenching time in the additive polarity winding was faster than that of the subtractive polarity winding or the resistivity type. A consumed energy in a superconducting element was represented as $W= VIt=I^2Rt$. We found that there was a difference in the consumed energies in accordance with winding types because of differences in voltages imposed on a superconducting element in accordance with a winding direction.

• Nuclear Engineering and Technology
• /
• v.49 no.4
• /
• pp.710-720
• /
• 2017

In Korea, many nuclear power plants operate at a single site based on geographical characteristics, but the population density near the sites is higher than that in other countries. Thus, multiunit accidents are a more important consideration than in other countries and should be addressed appropriately. Currently, there are many issues related to a multiunit probabilistic safety assessment (PSA). One of them is the quantification of a multiunit PSA model. A traditional PSA uses a Boolean manipulation of the fault tree in terms of the minimal cut set. However, such methods have some limitations when rare event approximations cannot be used effectively or a very small truncation limit should be applied to identify accident sequence combinations for a multiunit site. In particular, it is well known that seismic risk in terms of core damage frequency can be overestimated because there are many events that have a high failure probability. In this study, we propose a quantification method based on a Monte Carlo approach for a multiunit PSA model. This method can consider all possible accident sequence combinations in a multiunit site and calculate a more exact value for events that have a high failure probability. An example model for six identical units at a site was also developed and quantified to confirm the applicability of the proposed method.