• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.448-454
• /
• 2020

This study aims to determine the cause of structural defects occurring during aircraft operations and to verify the structural integrity of the improved features. The fracture plane was analyzed to verify the characteristics of the cracks and the fatigue failure leading to the final fracture was determined by the progress of the cracks by the repeated load. During aircraft operations, the comparative analysis of the load measurement data at the cracks with the aircraft design load determined that the measured load was not at the level of 30% of the design to be capable of being damaged. A gap analysis resulted in a significant stress of approximately 32 ksi at the crack site. Pre-Load testing also confirmed that the M.S. was reduced by more than 50% from +0.71 to +0.43, resulting in a sharp increase in aircraft load and the possibility of cracking when combined. Thus, structural reinforcement and the removal of the gap for aircraft cracking sites improved the defect. Based on the structural strength analysis of the improvement features, the bulkhead has a margin of about +0.88 and the fitting feature is about +0.48 versus allowable stress. In addition, the life analysis results revealed an improvement of approximately 84000 hours.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.53-60
• /
• 2020

The bogies of railway vehicles are one of the most critical components for service. Fatigue defects in the bogie can be initiated for various reasons, such as material imperfection, welding defects, and unpredictable and excessive overloads during operation. To prevent the derailment of a railway vehicle, it is necessary to evaluate and detect the defect of a connection weldment between the car body and bogie accurately. The safety of the bogie weldment was checked using an ultrasonic test, and it is necessary to determine the occurrence of defects using a learning method. Recently, studies on deep learning have been performed to identify defects with a high recognition rate with respect to a fine and similar defect. In this paper, the databases of weldment specimens with artificial defects were constructed to detect the defect of a bogie weldment. The ultrasonic inspection using the wedge angle was performed to understand the detection ability of fatigue cracks. In addition, the convolutional neural network was applied to minimize human error during the inspection. The results showed that the defects of connection weldment between the car body and bogie could be classified with more than 99.98% accuracy using CNN, and the effectiveness can be verified in the case of an inspection.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.4
• /
• pp.137-146
• /
• 1999

Inspection becomes to be important in the safety of structure and economical viewpoint, because structural damage accompanies lots of economical cost and social problems. Especially ship structure is composed of a lot of members and it is impossible to inspect all members continuously. The purpose of this paper is to get optimal inspection plan containing inspection time and method. Crack is one of major modes on the structural failure and can lead to collapse of structure. In this paper, the deteriorating process, which contains inspection to detect the crack before the propagation to large crack, is idealized as Markov chain model. Genetic algorithm is also used to accomplish the optimization of inspection plan. Especially, the probabilistic characteristics of cracks are changed, because ship is operating in corrosive environments and the scantling of structural members is reduced due to corrosion. Non-stationary Markov chain model is used to represent the process of corrosion in structural members. In this paper, the characteristics of indivisual inspection plan are compared by numerical examples for the change of corrosion rate, the cost due to scheduled system down and target failure probability. From the numerical example, it can be seen that the improvement of fatigue life for the members with short fatigue life is the most effective way in order to reduce total maintenance cost.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.1057-1063
• /
• 2023

The urban railway sleeper floating track, the subject of this study, is an anti-vibration track to reduce vibration transmitted to the structure. currently, the replacement cycle of resilience pad for sleeper floating tracks is set and operated based on load. however, most previous studies were conducted on load-based structural safety aspects, such as fatigue life evaluation of sleeper anti-vibration pads and increase in track impact coefficient and track support stiffness due to increase in spring stiffness. therefore, in this study, we measure the vibration acceleration of the ballast for each analysis section and use the results of 7 million fatigue tests to calculate the spring stiffness of the resilience pad for each section. the spring stiffness of the resilience pad calculated for each section was set as the analysis data and the concrete vibration acceleration was derived analytically. the adequacy of analysis modeling was verified as the analyzed concrete bed vibration acceleration for each section was within the field-measured concrete bed vibration acceleration range. using the vibration acceleration curve according to the derived spring stiffness change, the spring stiffness of the resilience pad is estimated from the measured vibration acceleration. therefore, we would like to present a technique that can estimate the spring stiffness of resilience pad of a running track using the vibration acceleration of the measured concrete bed.

• The Journal of Korean Medicine
• /
• v.44 no.4
• /
• pp.41-58
• /
• 2023

Objectives: This retrospective observational study aimed to investigate the efficacy and safety of Cheongpebaedok-tang, a traditional Korean herbal medicine, provided via telemedicine to patients with asymptomatic to mild COVID-19 in Korea. Methods: From February to April 2020, a retrospective analysis investigated COVID-19 patients treated via Korean telemedicine. The study involved asymptomatic to mild cases receiving Cheongpebaedok-tang more than three times, along with continuous Korean medicine care in convalescence. Diagnoses and treatment adhered to the telemedicine guidelines of the Association of Korean Medicine, with varied Cheongpebaedok-tang prescriptions based on symptom severity. Symptom evaluation involved a detailed assessment using a 15-item tool at initial and final sessions. Results: The study included 27 patients, with a mean age of 48.7 ± 2.3 years (mean ± standard error). Patients began self-administering oral Cheongpebaedok-tang for an average of 19.4 ± 1.8 days after the date of COVID-19 diagnosis confirmation and continued the medication for 15.8 ± 1.2 days. The reported side effects of the Cheongpebaedok-tang included palpitations (11.1%), insomnia (7.4%), dizziness (3.7%), and diarrhea (3.7%). All side effects disappeared after adjusting the prescription according to standard treatment guidelines. The occurrence of all COVID-19-related adverse symptoms, except fatigue and myalgia, decreased. Fatigue was the most common chronic symptom persisting after 6 months (51.9%), followed by ocular symptoms (37.0%) and sore throat (22.2%). Conclusions: This study implies Cheongpebaedok-tang may offer a potentially safe, symptom-alleviating approach for managing mild COVID-19 cases via telemedicine, although further comprehensive research is warranted.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.5
• /
• pp.535-543
• /
• 2017

Objective: This study was designed to identify factors affecting pilots' +Gz tolerance recovery from +Gz induced exhaustion. Background: +Gz tolerance of pilots has been considered as a crucial factor to fly the modern high performance fighter aircrafts. However, the factors affecting pilots' G-tolerance recovery from +Gz induced exhaustion have not been examined in the acceleration research community. Method: A centrifuge profile consisting of a high +Gz run for pilot's exhaustion and a low +Gz run for pilot's recovery and another high +Gz runs for pilot's second exhaustion was designed. The subjects' +Gz tolerance recovery ratio was measured by ratio of second high +Gz run time to the first high +Gz run time. The subjects' +Gz tolerance recovery rate was measured by dividing the subjects' +Gz tolerance recovery ratio by the low +Gz run time. The subjects' G-tolerance recovery rate was analyzed with respect to the subjects' personal factors including subjects' anthropometric and physiologic characteristics, flight time, flying aircraft type and so on. Results: The subjects' previous three-month flight hours (r=-0.336, p=0.039), six-month flight hours (r=-0.403, p=0.012) and one-year flight hours (r=-0.329, p= 0.044) correlated with the subjects' G-tolerance recovery rate. Conclusion: The subjects' G-tolerance recovery rate is clearly related to the subjects' previous flight hours. However, the subjects' anthropometric and physiologic characteristics do not show any statistically significant correlation with the subjects' G-tolerance recovery rate. Application: This research provides a safety critical insight to aviation community by identifying the factors to affect the gravity-induced loss of consciousness (GLOC) of pilots.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.11
• /
• pp.5587-5591
• /
• 2012

Objective: This study was performed to evaluated the efficacy and safety of continuous infusional paclitaxel and 5-Fu as first-line chemotherapy in patients with advanced esophageal squamous cell cancer (ESCC). Methods: A total of 22 patients with advanced esophageal squamous cell cancer with no indications for surgery and radiation therapy, or recurrent patients were enrolled from October 2008 to November 2010. All were treated with PTX 20 $mg/m^2$ was administered through a 16 hours continuous intravenous infusion on days 1 to 3, 8 and 9. DDP 3.75 $mg/m^2$ was given on days 1 to 4 and 8 to 11, continuous infusional 5-FU over 24-hours on days 1 to 5 and 8 to 12 at a dose of 375 $mg/m^2$, and folacin 60 mg orally synchronized with 5-Fu. The treatment was repeated every 21 days for at least two cycles. Results: 22 cases of all enrolled patients could be evaluated for the effect of treatment: 2 cases were CR, 9 cases PR, 5 cases SD and 2 cases PD, giving an overall response rate of 68.2%(15/22). The median time to progression was 7.0 months. The adverse reactions related to chemotherapy were tolerable; the most common toxic effects were marrow depression, alopecia, and fatigue. Conclusion: Low-dose continuous infusional PTX over 16-hours and 5-fu over 24-hours is a promising regimen with good tolerability in treating patients with advanced esophageal squamous cell cancer.

• Structural Engineering and Mechanics
• /
• v.63 no.6
• /
• pp.809-824
• /
• 2017

The accurate evaluation of wind characteristics and wind-induced structural responses during a typhoon is of significant importance for bridge design and safety assessment. This paper presents an expectation maximization (EM) algorithm-based angular-linear approach for probabilistic modeling of field-measured wind characteristics. The proposed method has been applied to model the wind speed and direction data during typhoons recorded by the structural health monitoring (SHM) system instrumented on the arch Jiubao Bridge located in Hangzhou, China. In the summer of 2015, three typhoons, i.e., Typhoon Chan-hom, Typhoon Soudelor and Typhoon Goni, made landfall in the east of China and then struck the Jiubao Bridge. By analyzing the wind monitoring data such as the wind speed and direction measured by three anemometers during typhoons, the wind characteristics during typhoons are derived, including the average wind speed and direction, turbulence intensity, gust factor, turbulence integral scale, and power spectral density (PSD). An EM algorithm-based angular-linear modeling approach is proposed for modeling the joint distribution of the wind speed and direction. For the marginal distribution of the wind speed, the finite mixture of two-parameter Weibull distribution is employed, and the finite mixture of von Mises distribution is used to represent the wind direction. The parameters of each distribution model are estimated by use of the EM algorithm, and the optimal model is determined by the values of $R^2$ statistic and the Akaike's information criterion (AIC). The results indicate that the stochastic properties of the wind field around the bridge site during typhoons are effectively characterized by the proposed EM algorithm-based angular-linear modeling approach. The formulated joint distribution of the wind speed and direction can serve as a solid foundation for the purpose of accurately evaluating the typhoon-induced fatigue damage of long-span bridges.

• Explosives and Blasting
• /
• v.28 no.1
• /
• pp.1-10
• /
• 2010

In blasting for lighting, fatigue behaviors of pillars such as destruction and deformation may occur due to blasting vibration and flyrock, which may cause collapses of cavities. This study aims to identify dynamic behavior of pillars to maintain efficient safety of cavities in large drafts. when they collide with flyrocks under blasting for the excavation. For the purpose, we compared ground vibration around pillar when flyrock collided with the pillar and that when explosive blast happened for the excavation. we conducted fragmentation analysis of the flyrock and compared impact vibration obtained from empirical equation with ground vibration obtained from regression analysis of real vibration data. also we compared those with results analyzed from numerical analysis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.77-82
• /
• 2012

It is well known that the targeted fuel efficiency could only be achieved by more than 40% reduction of the vehicle weight through improved design and extensive utilization of lightweight materials. In order to obtain the goal of the weight reduction of automobiles, the researches about lighter and stronger rear sub-frame have been studied without sacrificing the safety of rear sub-frame. In this study, the weight reduction design process of rear sub-frame could be proposed based on the variation of von-Mises stress contour by substituting an AA6061 (aluminum 6061 alloy) having tensile strength of 310 MPa grade instead of SAPH440 steels. In addition, the stress ratio variations (stress over fatigue limit) of the rear sub-frame were examined and compared carefully. It could be reached that this approach method could be well established and be contributed for light-weight design guide and the optimum design conditions of the automotive rear sub-frame development.