• Journal of Power System Engineering
• /
• v.20 no.6
• /
• pp.40-45
• /
• 2016

The manufacturing process of large scaled Al 7050 alloy is difficult for the occurrence of solidification crack during casting. The aims of this study are the evaluations of microstructure and mechanical properties of extruded Al 7050 billet and ring forged one with large scale. Large scaled Al 7050 billet was casted by direct-chill casting process. The extruded and ring forged specimens were prepared from the casted ingot after residual stress relief and homogenization heat treatment, respectively. Microstructures, hardness and tensile test of the surface, middle and center part of each specimen were performed at room temperature. Sheared and elongated type grains were observed at the edge parts of surface and center area and its aspect ratios of grains were low and similar as 0.21 while that of middle area was closed to 0.92 value in ring forged Al 7050 alloy. The mechanical properties of extruded Al 7050 alloy were superior than those of ring forged one. The hardness values of surface and center part were slightly higher than that of middle part in ring forged Al 7050 alloy.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1099-1107
• /
• 2013

This study proposes a weight reduction design for urban transit, specifically, a Korean EMU carbody made of aluminum extrusion profiles, according to size optimization and useful material changes. First, the thickness of the under-frame, side-panels, and end-panels were optimized by the size optimization process, and then, the weight of the Korean EMU carbody could be reduced to approximately 14.8%. Second, the under-frame of the optimized carbody was substituted with a frame-type structure made of SMA 570, and then, the weight of the hybrid-type carbody was 3.8% lighter than that of the initial K-EMU. Finally, the under-frame and the roof-panel were substituted with a composite material sandwich to obtain an ultralight hybrid-type carbody. The weight of the ultralight hybrid-type carbody was 30% lighter than that of the initial K-EMU. All the resulting carbody models satisfied the design regulations of the domestic Performance Test Standard for Electrical Multiple Unit.

• The Korean Journal of Mycology
• /
• v.14 no.4
• /
• pp.265-271
• /
• 1986

To screen biologically active components of the higher fungi of Korea, the dried carpophores of Auricularia polytricha were extracted with water. The extract was examined for acute toxicity in ICR mice. A low molecular weight toxin of this fungus was purified by a acetone precipitation followed by cellulose, silica gel and Sephadex LH-20 column chromatography. Major symptoms of this toxin were decreasing of normal motility, eye extrusion, hair erection, shivering, trembling of head, paralysis, rapid running or moving before death and depression of respiration. The median lethal doses of the total extract were 1. 28 g/kg and 4. 31 g/kg by i.p. and p.o. administrations, respectively. The amounts of one mouse lethal unit of the total extract and final fraction that killed a 20 g mouse within 30 minutes were 28.5 and 12.0 mg/mouse, respectively.

• Imaging Science in Dentistry
• /
• v.35 no.2
• /
• pp.111-114
• /
• 2005

A 15-year-old patient, who had been diagnosed and treated as Burkitt cell type acute lymphoblastic leukemia (ALL-L3) already, visited our department. He complained of gingival enlargement and loosening teeth 1 month ago. The clinical examination revealed anterior open bite, gingival enlargement, and nontender swelling particularly in molar regions of both jaws. Deep periodontal pockets and severe mobility was shown on most of the teeth. The panoramic radiographs showed severe bone destruction and extrusion of the molars. The contrast enhanced CT showed multiple enhanced mass and bone marrow obliteration in both jaws. Chemotherapy was done and the swelling was subsided at 1 month later. In conclusion, radiologic findings of leukemia with soft tissue mass, known as chloroma or granulocytic sarcoma, mimic those of lymphoma, so blood test may be needed for the final diagnosis.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.437-440
• /
• 2008

This study enforced to produce the planting concrete block which could be applied to various slopes economically. First of all, the physical properties was investigated with the various types of aggregate and aggregate ratio of the paste for the lead to mixture proportion of the planting concrete. As a result, the orchid stone as aggregate and 30% of aggregate ratio of the paste were used as the basic mixture proportion considering 20${\sim}$30% of maintained void ratio for the growth of plant, over 20% of capillary suction for holding water, and 3MPa as the minimum strength. For the result of the test to the new planting block which was quite different from existing planting concrete block, it could complement the problems and be possible to produce effectively and economically because various slopes like $40^{\circ}{\sim}75^{\circ}$, continual produce by extrusion, and pumping out were possible were possible.

• Journal of the Korea Concrete Institute
• /
• v.26 no.6
• /
• pp.741-749
• /
• 2014

Prestressed hollow-core (PHC) slabs are structurally-optimized lightweight precast floor members for long-span concrete structures, which are widely used in construction markets. In Korea, the PHC slabs have been often used with cast-in-place (CIP) topping concrete as a composite slab system. However, the PHC slab members produced by extrusion method use concrete having very low slump, and it is very difficult to make sufficient roughness on the surface as well as to provide shear connectors. In this study, a large number of push-off tests was conducted to evaluate interfacial shear strengths between PHC slabs and CIP topping concrete with the key variable of surface roughness. In addition, the horizontal shear strengths specified in the various design codes were evaluated by comparing to the test results that were collected from literature.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.263-268
• /
• 1999

In this study, a new concept of aluminum-matrix composites and the possibility of in-situ processing are suggested, and preliminary results on AI- Ti system are presented. Fine powders of AI-lO% Ti were prepared by the gas atomization so that fine $Al_3Ti$ formed into flake shape. A 25v/o $Al_3Ti/Al$ composite sample was made by the pow­d er metallurgy process involving hot extrusion. Microstructure and mechanical behavior both at room temperature and high temperatures were analysed by OM, SEM, TEM and tension test. Microstructural characteristics and mechanical properties of the composites exhibited similar behavior to those of $SiC_w/2124$ composites. Merits and drawbacks of the $Al_3Ti/Al$ composites are discussed together with a possibility of further improvement.

• The Korean Journal of Pain
• /
• v.34 no.4
• /
• pp.447-453
• /
• 2021

Background: Provocative discography (PD) is a test that is useful in diagnosing discogenic pain (DP). In this study, to diagnose DP, we used a posterolateral approach of needle placement and followed pressure criteria laid down by the Spine Intervention Society. The aim was to identify the correlation between magnetic resonance imaging (MRI) findings (desiccation, high intensity zone and change in shape and size of the disc) and the results of PD. Methods: Records of 50 patients who underwent PD for DP were analyzed. A total of 109 PDs were performed, with 54 suspect and 55 control discs. Alternate pain generators were ruled out. Results: A total of 35 suspect discs were positive on PD. The mean disc pressure in the suspect disc was 31.9 ± 7.9 psi (range, 15-44). Of the 50 patients who underwent PD, 35 had positive MRI findings. A significant positive correlation was found only between disc desiccation and discography result (r = 0.6, P < 0.001). Logistic regression analysis revealed that only desiccation successfully predicted the result of discography (OR = 26.5, P < 0.001); a high intensity zone and a disc protrusion/extrusion had an OR 2.3 and 1.24, respectively. Disc desiccation of Pfirmann grade 3 or more had a sensitivity and specificity of 0.93 and 0.64 respectively in identifying painful discs; the positive likelihood ratio was 2.58 while the negative likelihood ratio was 0.11. Conclusions: In patients with DP, disc desiccation is the most useful MRI feature that predicts a painful disc on PD.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.521-528
• /
• 2021

The high-density fiber composite manufacturing method by the extrusion molding method has the characteristic that continuous production is possible, and the product is molded through a mold forming a specific cross-section. OPC is used as a defect material, an appropriate amount of SiO₂ is supplied for CaO reaction activity, and high density and high strength are expressed through steam and autoclave curing. However, due to the use of organic reinforcing fibers, the flame duration exceeds the regulations during the non-combustible performance test, making it difficult to secure performance. In this study, the product was produced by mixing alkali-resistant organic fiber and fly ash having voids as a binder by replacing the existing polypropylene fiber. appeared to be possible.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.27 no.3
• /
• pp.159-167
• /
• 2021

The need for biodegradable plastic continues to increase, improvement of physical properties is necessary for actual use in the market. In this study, composite film was produced by adding peroxide additives to bioplastic according to concentration to investigate changes in the melt index, elongation, morphology, and TGA of the composite film. The addition of peroxide compatibilizer showed superior elongation of film and TGA compared to those of control. The added amount of compatibilizer affected the extrusion process, and it was revealed that adding an appropriate amount of peroxidizer is important. Analysis of the composite film's morphology revealed a heterogeneous dispersion sequence due to different rates of crystallization depending on the resin, and surface physical properties were best in the group added with 4% peroxide. The results above showed that the test group added with 4% peroxide compatibilizer was superior in the production of composite biodegradable film.