• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.11a
• /
• pp.43-49
• /
• 2002

A7003 alloy has characteristics of their excellent weldability, high corrosion resistance and superior plastic working however the broadening of application for the alloy has been hampered by the lower extrudability associated by Mg content. For improvement of extrudability and enhanced recovery efficiency during Al scrap recyeling, it has been generally practiced to reduce Mg content in A7003 alloy. Therefore, it is necessary to investigate the influence of Mg content on mechanical strength and extrudability of A7003 alloy. For efficient material processing which has small amounts, life cycle assessment in material processing(MLCA) is evaluated. The quantitative analysis of energy requirements and $CO_2$ emission for production of A7003 extruded bar are estimated with different Mg content and billet pre-heating process (heating source by light oil or LPG). In particular, the estimation of energy requirements was performed within shipping and gating range (except the mining and extraction stages)to investigate the influence of the variables on energy requirements and $CO_2$ emission in detail. As Mg content increased, the flow stress and the extrusion pressure for A7003 alloy increased. It has been thought that an increment in extrusion pressure with increasing Mg content is caused by the solid solution hardening of Mg atoms in the matrix and increment in volume fraction of intermetallic compound, $Mg_2Si$. The extrudability and the tensile strength are equal to, or above that of conventional A 7003 alloy even the content of Mg varied from $1.1wt.\%\;to\;0.5wt.\%$ alloy. This means that minimizing the content of Mg in A7003 alloy can enhance recovery efficiency during Al scrap recycling. It can be quoted that rather than Mg content energy source for billet heating is a prime factor to determine the atmospheric $CO_2$ emission.

• Transactions of Materials Processing
• /
• v.15 no.4 s.85
• /
• pp.274-280
• /
• 2006

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2006.04a
• /
• pp.640-641
• /
• 2006

• Journal of Pharmaceutical Investigation
• /
• v.5 no.1
• /
• pp.41-48
• /
• 1975

Extrusion-Spheronization Processing (ESP) was applied to preparate sustained release spherical particles as a form of matrix spherical particle (MSP). dl-methylephedrine HCI (ME) was the drug chosen and several dissolution retardants and binders were selected to estimate a relatively good formulation on this purpose. The effect of physicochemical nature, concentration, and solvents of these dissolution retardants and binders on regularity in shape of MSP and in vitro release rate was investigated. The effect of Particle size of matrix particles was also evaluated. It is, therefore, concluded that this ESP would be a relatively good preparation method of sustained release MSP of ME which has the sustained action of about 5 and 8 hours by formulating of ethylcellulose and ethylcellulose-paraffin as a dissolution retardant, respectively, and then ethylcellulose solution of 80% EtOH is recommended as a binder.

• Transactions of Materials Processing
• /
• v.23 no.3
• /
• pp.178-183
• /
• 2014

Continuous casting is a process where molten metal is solidified into a semi-finished billet on a large scale with either a rectangular or round cross section for subsequent processing. The use of continuous casting provides an opportunity for producing material on a practical industrial scale with lower cost than conventional casting. In the current study, the material was fabricated by continuous casting and subsequent extrusion. Tensile tests were conducted on continuous cast ZK60A after extrusion over a range of strain rates at temperatures from 473K to 623K. The alloy exhibits a quasi-superplastic behavior with a maximum recorded elongation of ~250% at 523K when tested with an initial strain rate of $10^{-5}/s$. The experiments give a strain rate sensitivity exponent of 0.3~0.4 and an activation energy of 108 kJ/mol. From the current investigation, it was found that the high-temperature plastic flow of the ZK60A is controlled by a dislocation viscous glide mechanism.

• Journal of Periodontal and Implant Science
• /
• v.45 no.2
• /
• pp.46-55
• /
• 2015

Purpose: This study evaluated the mechanical and structural properties of biphasic calcium phosphate (BCP) blocks processed using a modified extrusion method, and assessed their in vivo effectiveness using a rabbit calvarial defect model. Methods: BCP blocks with three distinct ratios of hydroxyapatite (HA):tricalcium phosphate (TCP) were produced using a modified extrusion method:HA8 (8%:92%), HA48 (48%:52%), and HA80 (80%:20%). The blocks were examined using scanning electron microscopy, X-ray diffractometry, and a universal test machine. Four circular defects 8 mm in diameter were made in 12 rabbits. One defect in each animal served as a control, and the other three defects received the BCP blocks. The rabbits were sacrificed at either two weeks (n=6) or eight weeks (n=6) postoperatively. Results: The pore size, porosity, and compressive strength of the three types of bone block were $140-170{\mu}m$, >70%, and 4-9 MPa, respectively. Histologic and histomorphometric observations revealed that the augmented space was well maintained, but limited bone formation was observed around the defect base and defect margins. No significant differences were found in the amount of new bone formation, graft material resorption, or bone infiltration among the three types of BCP block at either of the postoperative healing points. Conclusions: Block bone substitutes with three distinct compositions (i.e., HA:TCP ratios) processed by a modified extrusion method exhibited limited osteoconductive potency, but excellent space-maintaining capability. Further investigations are required to improve the processing method.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.521-529
• /
• 2007

This paper is concerned with the analysis on the surface expansion of AA 2024 and AA 1100 aluminum alloys in backward extrusion process. Due to heavy surface expansion appeared usually in the backward can extrusion process, the tribological conditions along the interface between the material and the punch land are very severe. In the present study, the surface expansion is analyzed especially under various process conditions. The main goal of this study is to investigate the influence of degree of reduction in height, geometries of punch nose, friction and hardening characteristics of different aluminum alloys on the material flow and thus on the surface expansion on the working material. Two different materials are selected for investigation as model materials and they are AA 2024 and AA 1100 aluminum alloys. The geometrical parameters employed in analysis include punch corner radius and punch nose angle. The geometry of punch follows basically the recommendation of ICFG and some variations of punch geometry are adopted to obtain quantitative information on the effect of geometrical parameters on material flow. Extensive simulation has been conducted by applying the rigid-plastic finite element method to the backward can extrusion process under different geometrical, material, and interface conditions. The simulation results are summarized in terms of surface expansion at different reduction in height, deformation patterns including pressure distributions along the interface between workpiece and punch, comparison of surface expansion between two model materials, geometrical and interfacial parametric effects on surface expansion, and load-stroke relationships.

• Korean Journal of Food Science and Technology
• /
• v.27 no.6
• /
• pp.934-938
• /
• 1995

Water soluble fractions (WSF) of wheat bran treated with thermal processes such as autoclaving, microwaving and extrusion were characterized to investigate the structural response of plant cell wall to thermal and mechanical energy. From the chemical analysis and gel filtration chromatography of WSF, gelatinization of starch was found to be the primary solubilizing mechanism of wheat bran, followed by the structural disintegration of fibrous non-starch cell wall materials. It was also found that extrusion process resulted in degrading relatively higher molecular weight non-starch polysaccharides from the cell wall. GC analysis of water soluble non-starch polysaccharides indicates that the arabinoxylan residues of cell wall are the most susceptible site to thermal treatments studied. In particular, the degrading degree of cell wall of wheat bran is the most significant for extrusion accompanying both high temperature and high shear.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.32 no.8
• /
• pp.1270-1277
• /
• 2003

The extrusion conditions of the soymilk residue and corn grits mixtures were optimized. The experiment was designed according to the D-optimal design of response surface methodology (RSM), which shows 18 experimental points including 4 replicates for three independent variables (screw speed, water content and die temperature). The responses variables such as bending force, expansion ratio, bulk density, water solubility index (WSI), water absorption index (WAI), and color values (L＊, a＊, b＊) were evaluated using response surface analysis. Expansion ratio and WSI decreased with increasing water content, whereas bulk density tended to increase with increasing water content. While greater screw speeds enhanced WSI and yellowness, higher moisture contents decreased the expansion ratio and WSI value. However, die temperature did not influence upon the response variables. The optimum extrusion conditions by numerical and graphical methods were similar: the screw speed, water content, and die temperature were 250 rpm, 22.43% and l28.16$^{\circ}C$ by the numerical method; 250 rpm, 22.43%, and 128.02$^{\circ}C$ by graphical method.

• Transactions of Materials Processing
• /
• v.4 no.2
• /
• pp.131-140
• /
• 1995

In this paper damage propagation of a material during forming is investigated with the concept of continuum damage mechanics. An isotropic damage model based on the theory of materials of type N is adopted to describe the damage process of a ductile material with large elasto-viscoplastic deformation. The stiffness degradation of the loaded material is chosen as a damage measure. The highly nonlinear equilibrium equations are reduced to the incremental weak form and approximated by the total Lagrangian finite element method. To simulate contact condition, extended interior penalty method with modified coulomb friction law is adopted. The displacement control method along with the modified Riks' continuation technique is used to solve the incremental iterative equations. As numerical examples, upsetting problem and backward extrusion problem are simulated and the results of damage propagation and $J_2$ stress contours with and without friction are presented.