• 한국식품과학회지
• /
• 제33권1호
• /
• pp.55-59
• /
• 2001

쌀의 팽화에 관한 연구는 팝콘에 관한 연구와 비교하면 매우 미흡한 편이다. 쌀을 팽화시킬 때 대부분 가압식 팽화기나 압출성형기를 이용하고 있다. 대부분의 쌀의 팽화에 관한 연구는 인도에서 이루어져 왔으며, 가공조건(수분함량, 가열온도) 등이 팽화쌀의 물리화학적 성질에 관한 연구가 대부분이다. 팝콘과 같은 인스턴트 팽화쌀의 팽화기작 및 개발에 관한 연구는 극히 제한되어 있다. 압출성형 팽화펠릿의 팽화에서 3일 수침 후 분쇄한 찹쌀을 이용하여 수분함량 $20{\sim}27%$, $CO_2$ 가스주입압력 2.8 MPa, 스크류회전속도 200 rpm으로 제조한 펠릿을 microwave oven에서 팽화시 밀도와 조직감이 비교적 낮게 나타나는 경향을 보였다. 또한 압출성형기로 제조된 펠릿의 팽화시 가장 큰 영향인자는 펠릿의 수분함량과 가스주입압력, 스크류회전속도의 조절에 의해 팽화 및 조직감을 최적화 할 수 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.170-173
• /
• 2001

The design for cold extrusion dies is very important because the die insert is subjected to very high radial and hoop stresses. The design of cold extrusion dies has many constrained conditions. In this paper, two assumptions were proposed. First assumption was selected by yielding strength dependent on the to hoop stress of each ring in dies. Second assumption is that the maximum inner pressure is determined when yielding occurs in one ring of dies. To obtain the maximum inner pressure the flexible tolerance method was applied. A comparison of design values between the proposed method and the conventional method has been discussed.

• 소성∙가공
• /
• 제3권1호
• /
• pp.23-37
• /
• 1994

The upper bound element technique(UBET) is used to analyze the final stage of the axisymmetric forward extrusion. Kinematically admissible velocity field involving curved surface of velocity discontinuity is assumed. The required power to arise the piping defect is obtained and is compared with Aviture's solution a the same condition. Conditions for inception of the cavity and development of the pipe are predicted. The internal radius of the pipe and critical length of billet are also determined. Experiments are carried out for extrusion with lead specimens to investigate the piping phenomena. The theoretically predicted results showed reasonably good agreement with the experimental observation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.106-109
• /
• 2001

The use of ceramic inserts in hot extrusion dies offers significant technical and economic advantages over other forms of manufacture. These potential benefits can however only be realized by optimal design of the tools so that the ceramic inserts are not subjected to stresses that lead to their premature failure. In this paper, process simulation and stress analysis are thus combined during the design, and a data exchange program has been developed that enables optimal design of the dies taking into account the elastic deflections generated in shrink fitting the die inserts and that caused by the stresses generated in the process. The stress analysis of the dies is used to determine the stress conditions on the ceramic insert by considering contact and interference effects under both mechanical and thermal loads. The results are compared with the experimental ones for verification.

• 한국분말재료학회지
• /
• 제15권3호
• /
• pp.204-209
• /
• 2008

Aluminum alloys are not only lightweight materials, but also have excellent thermal conductivity, electrical conductivity and workability, hence, they are widely used in industry. It is important to control and enhance the densification behavior of metal powders of aluminum. Investigation on the extrusion processing combined with equal channel angular pressing for densification of aluminum powders was performed in order to develop a continuous production process. The continuous processing achieved high effective strain and full relative density at $200^{\circ}C$. Optimum processing conditions were suggested for good mechanical properties. The results of this simulation helped to understand the distribution of relative density and effective strain.

• 소성∙가공
• /
• 제24권5호
• /
• pp.332-339
• /
• 2015

In the current paper, a cold forging sequence was developed to manufacture a precisely cold forged H/Lower, which is used as the air back unit in commercial automobiles. The preform shape of the H/Lower influences the dimensional accuracy and stiffness of the final product. The shape factor (SF) ratio and shape of the tools are considered as the design parameters to achieve adequate backward extrusion height and maintain appropriate thickness variations. The optimal conditions of the design parameters were determined by using an artificial neural network (ANN). To experimentally verify the optimal preform and tool shapes, the experiments of the backward extrusion of the H/Lower were executed. The process design methodology proposed in the current paper, can provide a more systematic and economically feasible means for designing the preform and tool shapes for cold forging.

• Preventive Nutrition and Food Science
• /
• 제19권2호
• /
• pp.124-127
• /
• 2014

The effect of feed moisture contents (30%, 40%, and 50%) and screw speed (200 rpm, 250 rpm, and 300 rpm) on the corn fiber gum (CFG) yield and soluble arabinoxylans (SAX) content of destarched corn fiber was investigated. The CFG yields and SAX contents of extruded, destarched corn fiber were higher than that of destarched corn fiber. In extruded, destarched corn fiber, increased screw speed and decreased feed moisture contents resulted in a higher SAX contents. The maximum yields of CFG obtained from extruded, destarched corn fiber were $79.1{\pm}19.0g/kg$ (30% feed moisture content) and $82.3{\pm}11.30g/kg$ (300 rpm screw speed). The highest SAX content was also observed at a screw speed of 300 rpm. The results of the present study show that water extraction and extrusion combined have the potential to increase CFG and SAX yields from corn fiber.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 추계학술대회논문집
• /
• pp.29-37
• /
• 1996

A ductile fracture criterion, which has already proposed, namely, ($\Delta$1/1o)f at $\Delta$$\sigma$ m=(($\Delta$1/1o)f+(-1/tan$\theta$)$\Delta$$\sigma$m(where ($\Delta$1/1o)f is fracture elongation, $\Delta$$\sigma$m is mean stress variation) was made use of to study the working limit in axisymmetric extrusion. The present investigation is concerned with the application of theory on flow and fracture to the prediction of workability of materials in axisymmetric bar extrusion, with special reference to central bursting. The influenced of die geometry and manufacturing conditions on the central bursting are predicted.

• 소성∙가공
• /
• 제13권7호
• /
• pp.623-628
• /
• 2004

This paper is concerned with pressure welding, which has been known as a main bonding mechanism during the cold and warm forming such as clad extrusion or bundle extrusion/drawing. Bonding characteristics between the Cu and Al plates by pressure welding are investigated focusing on the weak bonding. Experiments are performed at the cold and warm temperatures ranging from the room temperature to $200^{\circ}C$. The important factors examined in this work are the welding pressure, pressure holding time, surface roughness, and temperature. A bonding map, which can identify the bonding criterion with a weak bonding strength of IMPa , is proposed in terms of welding pressure and surface roughness fur the cold and warm temperature ranges.

• 소성∙가공
• /
• 제28권3호
• /
• pp.123-129
• /
• 2019

Hypereutectic Al-Si alloys have been widely utilized for wear-resistant components in the automotive industry. In order to expand the application of Hypereutectic Al-Si alloys, the addition of alloying elements forming a stable precipitate at high temperature is required. Thermally stable inter metallic compounds can be formed through the addition of transition elements such as Fe, Ni to Al alloys. However, the amount of transition element to be added to Al alloys is limited due to their low solid solubility. Also, hypereutectic Al-Si-Fe alloys form coarse primary Si phases and needle-shaped intermetallic compounds during solidification in the general casting processes. In this study, the effects of the destruction of Intermetallic compound and Si phase are investigated via hot extrusion. Both the microstructure and mechanical properties are discussed under different extrusion conditions.