• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.15-27
• /
• 2004

Sliding aspects of rock slope, where large-scaled tension cracks are induced during preliminary excavation, have been analyzed. Structure of rock mass is investigated by performing the electrical resistivity survey and the orientations and positions of discontinuities are measured from DOM-drilled core log. Geological evidence far primary failure movement has been detected and clay minerals which possess swelling properties are identified through XRD analysis. Slope stability is examined by considering the orientations of discontinuities and their trace distributions on the cut-face and neighboring natural slope surface. Both orientations and positions of failure-invoking discontinuity planes, traces of which are exposed within the anticipated sliding region, are concerned fur analyzing the preferred sliding directions. Regional sliding vectors are assessed based on the relative positions of potential sliding planes in the boreholes and the general trend of anticipated failure movement of rock slope is also investigated.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.1
• /
• pp.73-80
• /
• 2016

Colorectal cancer is a very prevalent diagnosed cancer. The current study was performed in order to examine the role of BRAE (Basella rubra aqueous extract) in regulating aberrant crypt foci (ACF) formation, cell proliferation and inhibition of apoptosis in a colon carcinogenesis model in male Wistar rats. Rats were randomly allocated into six groups. Group I served as control, and group II acted as a drug control administered BRAE (250mg/kg b.w.) orally for 30 weeks. Rats in group III-VI were given subcutaneous injections of DMH (25mg/kg b.w. weekly) for 15 weeks to initiate colon carcinogenesis. Those in group IV and VI were administered BRAE along with DMH injections. Rats in group V were administered with BRAE after cessation of DMH injection. After 30 weeks of experimental period colons were obtained from experimental groups and analyzed for ACF incidence, argyrophilic nucleolar organizing region-associated proteins (AgNOR) count, histopathological and immunohistochemical changes. Only in DMH exposed groups were ACF and AgNOR numbers increased. Administration of BRAE appreciably decreased the numbers of ACF and AgNOR in BRAE treated groups. Histopathological findings revealed a high level of dysplastic changes with decreased number of goblet cells found only in only DMH injected rats. Administration of BRAE in treated group rats reversed these changes. Expression markers for cell proliferation (PCNA and Ki67) were elevated in DMH treated rats, but reduced with BRAE treatement. This expression was reversed with apoptosis markers (p53 and Caspase-3). Thus the results results of the present study were found to be significant and confirmed the potential efficacy of BRAE against colon carcinogenesis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.769-774
• /
• 2013

Turbine blades and disc, which are one of the most important rotating parts of a gas turbine engine, are required to have highly efficient performance in order to minimize the total life cycle costs. Owing to these requirements, these components are exposed to severe conditions such as extreme turbine inlet temperatures, high compression ratios, and high speeds. To evaluate the structural integrity of a turbine disc under these conditions, material modeling and finite element analysis techniques are essential; furthermore, shape optimization is necessary for determining the optimal solution. This study aims to generate 2D finite element models of an axisymmetry model and a sector one and to perform thermal-structural coupled-field analysis and contact analysis. Structurally vulnerable areas such as the disc bore and disc-blade interface region are analyzed by a parametric study. Finally, an improved design is provided based on the results, and the necessity of elaborate shape optimization is confirmed.

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.6
• /
• pp.663-671
• /
• 2011

Although a scooter is a convenient transportation means for a short distance traveling with a light package in the congested urban center, it might be one of the significant sources of air pollutants to which many people can easily be exposed during its passing-by. In this paper, we measured concentrations of gases and particles emitted from a scooter at roadside with no other traffic. To understand the characteristics of scooter emissions with respect to driving speed (idling, 30 km/h) at the roadside, total particle number concentration, particle size distribution, average surface area of particles deposited in the alveolar region, and concentrations of black carbon, CO, and $NO_x$ were measured. The concentrations of the particle number, surface area of deposited particles, CO, and $NO_x$ were highly fluctuated in the scooter's idling condition. The trends of particle number concentration, CO, and $NO_x$ generation were similar to one another. When the scooter started to move, all of $NO_x$, CO and particle number concentrations increased and after it passed by at the speed of 30 km/h, the concentration peaks of the particles and gases appeared at the same time. Unimodal size distribution with ~70 and ~93 nm mode diameters was observed for the idling and cruising condition, respectively. From this work, we found that emission from a passing vehicle could be characterized using a roadside monitoring technique.

• Transactions of Materials Processing
• /
• v.29 no.4
• /
• pp.194-202
• /
• 2020

In this paper, experimental and numerical study on a combined sheet metal forming and plate forging of a seal part of a passenger car's hub bearing is conducted to develop the new process of which target is to remove machining process by plate forging and to achieve near-net shape manufacturing. The previous process of a sheet metal forming inevitably needed a machining process for making stepped sheet after conventional sheet metal forming in a progressive way. The stepped sheet is intended to be formed by plate forging in this study. Through the systematic way of developing the combined forming process using solid elements based-elastoplastic finite element method (FEM), several conceptual designs are made and an optimized process design in terms of geometric dimensioning and tolerance of straightness of the thin part is found, which is exposed to bending in metal forming of axisymmetric part. The predicted straightness measured by the slope angle of the tilted thin region is compared with the experimental straightness, showing that they are in a good agreement with each other. Through this study, a systematic approach to optimal process design, based on elastoplastic FEM with solid elements, is established, which will contribute to innovating the conventional small-scaled sheet metal forming processes which can be dealt with by solid elements.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.5
• /
• pp.537-542
• /
• 2011

The thermo-mechanical interaction between brake block and wheel tread during braking has been found to cause thermal crack on the wheel tread. Due to thermal expansion of the rim material, the thermal cracks will protrude from the wheel tread and be more exposed to wear during the wheel/block contact than the rest of the tread surface. The wheel rim is in residual compression stress when is new. After service running, the region in the tread has reversed to tension. This condition can lead to the formation and growth of thermal cracks in the rim which can ultimately lead to premature failure of wheel. In the present paper, the thermal cracks of railway wheel, one of severe damages on the wheel tread, were evaluated to understand the safety of railway wheel in running condition. The residual stresses for damaged wheel which are applied to tread brake are investigated. Mainly X-ray diffusion method is used. Under the condition of concurrent loading of continuous rolling contact with rails and cyclic frictional heat from brake blocks, the reduction of residual stress is found to correlate well with the thermal crack initiation.

• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.18-25
• /
• 2010

Super-duplex stainless steels (SDSS) have a good balance of mechanical property and corrosion resistance when they consist of approximately equal amount of austenite and ferrite. The SDSS needs to avoid the detrimental phases such as sigma(${\sigma}$), chi(${\chi}$), secondary austenite(${\gamma}2$), chromium carbide & nitride and to maintain the ratio of ferrite & austenite phase as well known. However, the effects of the subsequent weld thermal cycle were seldom experimentally studied on the micro-structural variation of weldment & pitting corrosion property. Therefore, the present study investigated the effect of the subsequent thermal cycle on the change of weld microstructure and pitting corrosion property at $40^{\circ}C$. The thermal history of root side was measured experimentally and the change of microstructure of weld root & the weight loss by pitting corrosion test were observed as a function of the thermal cycle of each weld layer. The ferrite contents of root weld were reduced with the subsequent weld thermal cycles. The pitting corrosion was occurred in the weld root region in case of the all pitted specimen & in the middle weld layer in some cases. And the weight loss by pitting corrosion was increased in proportional to the time exposed at high temperature of the root weld and also by the decrease of ferrite content. The subsequent weld thermal cycles destroy the phase balance of ferrite & austenite at the root weld. Conclusively, It is thought that as the more subsequent welds were added, the more the phase balance of ferrite & austenite was deviated from equality, therefore the pitting corrosion property was deteriorated by galvanic effect of the two phases and the increase of 2nd phases & grain boundary energy.

• Korean Journal of Veterinary Service
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2001

This study was carried out to investigate and analyze the gross lesions of lungs in slaughtered pigs. Pigs were collected from the areas of Kyounggj, Chungbuk, Chungnam and Kangwon provinces from November to December 1999. One hundred-eleven pigs(17.4%) had lung lesions with various degrees among 639 pigs tested. By the standard scoring system, mean score of the lung lesion was 25.6+13.2. Regional prevalence of lung lesions were 23.5%(8/34)) in Kangwon, 17.3%(61/352) in Kyunggi, 15.7%(32/204) in Chungnam and 20.4%(10/49) in Chungbuk. Mean number of pulmonary lesions per pig were 2.87. Most frequent region with pulmonary lesions was right cranial lobe(30.1%) and the decreasing prevalence rates were followed by 23.8% in right middle lobe, 21.05 in right accessory lobe, 15.0% in left cranial lobe, and 5.0% in left middle and accessory lobe(5.0%) and also there was the same prevalent tendency on pulmonary lesions in each lobes of 111 pigs with gross lesion. Isolation rate of bacteria from the affected lungs was 72.1% and main pathogen was Pasteurella multocida. Gross and histological examination of pulmonary lesions in some pigs suggested that there were no marked changes regarded as the correlation with specific diseases except fibropurulent bronchopneumonia which was suspective of some respiratory bacteria including Pasteurella multocida and peribronchiolar lymphoid hyperplasia in varying degrees which was strongly associated with mycoplasmal infection. Consequently, the results in the study were suggested that there was consistently exposed against many causative factors including bacteria in the considerable number of pig herds rearing in the middle area in Korea.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.423-423
• /
• 2011

Zinc oxide is metal oxide semiconductor with the 3.37 eV bandgap energy. Zinc oxide is very attractive materials for many application fields. Zinc Oxide has many advantages such as high conductivity and good transmittance in visible region. Also it is cheaper than other semiconductor materials such as indium tin oxide (ITO). Therefore, ZnO is alternative material for ITO. ZnO is attracting attention for its application to transparent conductive oxide (TCO) films, surface acoustic wave (SAW), films bulk acoustic resonator (FBAR), piezoelectric materials, gas-sensing, solar cells and photocatalyst. In this study, we synthesized ZnO nanoparticles and defined their physical and chemical properties. Also we studied about the application of ZnO nanoparticles as a photocatalyst and try to find a enhancement photocatalytic activity of ZnO nanorticles.. We synthesized ZnO nanoparticles using spray-pyrolysis method and defined the physical and optical properties of ZnO nanoparticles in experiment I. When the ZnO are exposed to UV light, reduction and oxidation (REDOX) reaction will occur on the ZnO surface and generate O2- and OH radicals. These powerful oxidizing agents are proven to be effective in decomposition of the harmful organic materials and convert them into CO2 and H2O. Therefore, we investigated that the photocatalytic activity was increased through the surface modification of synthesized ZnO nanoparticles. In experiment II, we studied on the stability of ZnO nanoparticles in water. It is well known that ZnO is unstable in water in comparison with TiO2. Zn(OH)2 was formed at the ZnO surface and ZnO become inactive as a photocatalyst when ZnO is present in the solution. Therefore, we prepared synthesized ZnO nanoparticles that were immersed in the water and dried in the oven. After that, we measured photocatalytic activities of prepared samples and find the cause of their photocatalytic activity changes.

• Journal of Biosystems Engineering
• /
• v.27 no.4
• /
• pp.341-348
• /
• 2002

Quality evaluation of red ginsengs is determined by outer shape and inner qualities. Especially, the inner qualities are main grading criteria. Currently, red ginsengs are classified into 3-grades; heaven, earth and good. The best heaven grade must not include inner holes and sponge tissues. This study was conducted to develop a red ginseng sorting system using x-ray image processing technique. Because of lens characteristic, gray values of the central region in the x-ray image are higher and gradually decreased towards the edge regions. This difference of gray values gives trouble in segmentation and detection of inner holes in red ginseng image, so preprocessing technique is necessary. The preprocessing was done by subtracting source image from an empty background image. But, simple subtraction was not quite appropriate because of too small contrast between inner holes and sound part. Scaled subtraction images were obtained by multiplying all gray values by some numbers. However this method could not help to set threshold value because the gray values of root part are generally lower than body part when red ginseng is exposed to the x-ray. To determine threshold value for detecting inner holes, an algorithm was developed by increasing overall gray values of less clear images.