• Steel and Composite Structures
• /
• 제13권6호
• /
• pp.521-537
• /
• 2012

In this study, an experimental study is performed to understand the effect of spalling on the structural behavior of fire damaged steel reinforced high strength concrete (SRHSC) columns, and the test results of temperature distributions and the displacements at elevated temperature are analyzed. Toward this goal, three long columns are tested to investigate the effect of various test parameters on structural behavior during the fire, and twelve short columns are tested to investigate residual strength and stiffness after the fire. The test parameters are mixture ratios of polypropylene fiber (0 and 0.1 vol.%), magnitudes of applied loads (concentric loads and eccentric loads), and the time period of exposure to fire (0, 30, 60 and 90 minutes). The experimental results show that there is significant effect of loading on the structural behaviors of columns under fire. The loaded concrete columns result more explosive spalling than the unloaded columns under fire. In particular, eccentrically loaded columns are severely spalled. The temperature distributions of the concrete are not affected by the loading state if there is no spalling. However, the loading state affects the temperature distributions when there is spalling occurred. In addition, it is found that polypropylene fiber prevents spalling of both loaded and unloaded columns under fire. From these experimental findings, an equation of predicting residual load capacity of the fire damaged column is proposed.

• 한국해양공학회지
• /
• 제37권3호
• /
• pp.99-110
• /
• 2023

When a fire accident accompanied by an explosion occurs, the surrounding firewalls are affected by impact and thermal loads. Damaged firewalls due to accidental loads may not fully perform their essential function. Therefore, this paper proposes an advanced methodology for evaluating the fire resistance performance of firewalls damaged by explosions. The fragments were assumed to be scattered, and fire occurred as a vehicle exploded in a large compartment of a roll-on/roll-off (RO-RO) vessel. The impact velocity of the fragments was calculated based on the TNT equivalent mass corresponding to the explosion pressure. Damage and thermal-structural response analyses of the firewall were performed using Ansys LS-DYNA code. The fire resistance reduction was analyzed in terms of the temperature difference between fire-exposed and unexposed surfaces, temperature increase rate, and reference temperature arrival time. The degree of damage and the fire resistance performance of the firewalls varied significantly depending on impact loads. When naval ships and RO-RO vessels that carry various explosive substances are designed, it is reasonable to predict that the fire resistance performance will be degraded according to the explosion characteristics of the cargo.

• Computers and Concrete
• /
• 제7권2호
• /
• pp.159-167
• /
• 2010

This paper demonstrates numerical techniques for complex large-scale modeling with microplane constitutive theories for reinforced high strength concrete, which for these applications, is defined to be around the 7000 psi (48 MPa) strength as frequently found in protective structural design. Applications involve highly impulsive loads, such as an explosive detonation or impact-penetration event. These capabilities were implemented into the authors' finite element code, ParaAble and the PRONTO 3D code from Sandia National Laboratories. All materials are explicitly modeled with eight-noded hexahedral elements. The concrete is modeled with a microplane constitutive theory, the reinforcing steel is modeled with the Johnson-Cook model, and the high explosive material is modeled with a JWL equation of state and a programmed burn model. Damage evolution, which can be used for erosion of elements and/or for post-analysis examination of damage, is extracted from the microplane predictions and computed by a modified Holmquist-Johnson-Cook approach that relates damage to levels of inelastic strain increment and pressure. Computation is performed with MPI on parallel processors. Several practical analyses demonstrate that large-scale analyses of this type can be reasonably run on large parallel computing systems.

• 한국항공우주학회지
• /
• 제41권2호
• /
• pp.150-155
• /
• 2013

본 논문에서는 기존의 복잡한 구조를 가지는 비폭발식 분리장치를 단순화시켜 니크롬 와이어와 케블라 로프를 이용한 새로운 개념의 비폭발식 분리 메커니즘을 설계/제작하고 기초성능 평가(사전하중, 분리시간, 충격 실험 등)를 위한 실험을 수행하였다. 그 결과 니크롬 와이어의 회전횟수에 따라 다양한 사전하중 하에서 작동이 가능한 것을 확인하였고, 최대 6.0kN의 사전하중 하에서 110G의 충격을 발생시키며 680ms의 짧은 시간에 분리되는 것을 확인하여 제안된 분리장치의 유용성을 확인하였다. 추후 발사환경 및 우주환경 시험을 통하여 제안된 분리장치의 우주인증을 수행하고 다양한 사전하중에서 작동 신뢰도를 확보하여 태양 전지 패널의 전개뿐만이 아니라 페어링 분리 등 다양한 용도에 사용이 가능하도록 개발하고자 한다.

• 한국지반공학회논문집
• /
• 제20권4호
• /
• pp.89-102
• /
• 2004

디커플링장전조건의 화약 폭발시 발생하는 발파압력은 최대압력, 최대압력 도달시간, 압력파형의 함수로 나타난다. 발파 최대압력과 최대압력 도달시간은 화약과 암반 특성의 함수이다. 화약과 암반특성시험 결과로부터 그 특성치의 확률분포를 산출하였다. 화약과 암반 특성치의 확률분포가 정규분포로 나타났으므로 발파 최대압력과 최대압력 도달시간의 확률분포도 정규분포로 추정되었다. 발파 최대압력과 최대압력 도달시간에 가장 크게 영향을 미치는 변수를 파악하기 위하여 매개변수분석과 불확정성분석을 실행하였다. 최대압력과 최대압력 도달시간은 매개변수분석결과 화약특성에 가장 크게 영향을 받았지만 불확정성분석결과 화약보다 암반특성에 크게 영향을 받았다. 발파로 인하여 굴착선주 변 암반에 발생하는 손상을 수치해석으로 분석하였다. 암반손상을 산정하기 위하여 연속체손상역학에 기초하여 사용자 부 프로그램을 작성하였다. 이 부 프로그램을 ABAQUS 주 프로그램과 연결하여 해석하였다. 동적 해석결과는 확대공 발파에 의한 손상이 외곽공보다 크게 나타났다. 확대공 배치, 암반분류 세분화 등 여굴방지 방안이 제안되었다 손상계수의 파쇄기준이 불명확하므로 fuzzy-random 확률이론을 적용하여 파쇄기준과 파쇄영역을 명확하게 나타내었다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권11호
• /
• pp.647-657
• /
• 2004

Helical magneto-cumulative generator(HMCG)s are very useful devices in suppling pulsed high current to inductance loads. To apply fast high voltage pulses to high impedance loads, high current outputs of HMCGs are required to be conditioned to higher voltages by using various pulse components such as opening/closing switches and pulse transformer. In this paper, stepping with the trends of requirements for ever-increasing energy in pulsed power applications coupling methods is investigated to obtain higher output energy by connecting several HMCGs in series or parallel way. The coil dimension of HMCGs used in series or parallel connections was 50 mm in diameter and 150 mm in length. The coil was fabricated by using enamel-coated copper wire of 1 mm in diameter. The highest energy amplification ratio and peak voltage of load were achieved from the serially connected four-barrel HMCG system. They were 68 and 34 kV, respectively, when the initial energy of 0.36 kJ was supplied into that system with the load of 0.4 μH. Within the tested range of inductance ratio, energy amplification ratio was found to be highly dependent on the inductance ratio of serial- and parallel-connected HMCG systems to load, which to be optimal around 500 was turned out. The experimental results showed that the output energy and voltage of load are controlled by connecting HMCGs in series or parallel.

• 한국전산구조공학회논문집
• /
• 제24권6호
• /
• pp.629-636
• /
• 2011

최근 들어 여러 테러에 의한 폭발사건에서 유발된 위험상황에서 보듯이 폭발에 의한 인명피해나 시설물의 손상은 우리가 고려하는 재해수준을 넘는 비참한 결과를 항상 수반한다. 하지만 폭발에 대한 구조물의 설계는 그 연구나 대책이 상당히 미비한 실정이다. 이에 미국건물설계기준(UBC94)을 바탕으로 내진설계(Welded Moment Resistant Frame)된 10층 건물의 폭발에 대한 해석적 모델을 제공하고자 한다. 현재 폭발하중의 정량적인 결과는 미국 육군(U.S.Department of Army)에서 개발된 경험적 방법에 기반을 둔 프로그램을 통해 폭간거리에 따른 하중의 크기와 분포를 알 수 있다. 본 연구에 사용된 폭원의 성격은 반구형 표면 폭발(Hemispherical Surface Burst)의 경우를 사용하였으며, 또한 선형 및 비선형 시간 이력해석을 통해 건물의 변위, 상대변위, 요구/수행비 및 비선형 거동에 대한 해석적 결과를 제공하였다. 또한 현재 사용되고 있는 내진기준(FEMA356)에 적용하여 소성힌지의 거동을 통해 폭발에 대한 건물의 성능수준을 예상하였다.

• Advances in concrete construction
• /
• 제14권3호
• /
• pp.153-167
• /
• 2022

The interaction between blast load and structures, as well as the interaction among structural members may well affect the structural response and damages. Therefore, it is necessary to analyse more realistic reinforced concrete structures in order to gain an extensive knowledge on the possible structural response under blast load effect. Among all the civilian structures, columns are considered to be the most vulnerable to terrorist threat and hence detailed investigation in the dynamic response of these structures is essential. Therefore, current research examines the effect of blast loads on the reinforced concrete columns via development of Pressure- Impulse (P-I) diagrams. In the finite element analysis, the level of damage on each of the aforementioned RC column will be assessed and the response of the RC columns when subjected to explosive loads will also be identified. Numerical models carried out using LS-DYNA were compared with experimental results. It was shown that the model yields a reliable prediction of damage on all RC columns. Validation study is conducted based on the experimental test to investigate the accuracy of finite element models to represent the behaviour of the models. The blast load application in the current research is determined based on the Lagrangian approach. To develop the designated P-I curves, damage assessment criteria are used based on the residual capacity of column. Intensive investigations are implemented to assess the effect of column dimension, concrete and steel properties and reinforcement ratio on the P-I diagram of RC columns. The produced P-I models can be applied by designers to predict the damage of new columns and to assess existing columns subjected to different blast load conditions.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 봄 학술발표회 논문집
• /
• pp.1-8
• /
• 1994

An automated procedure which allows adaptation of spatial and time discretization simultaneously in finite element analysis of linear elastodynamic problems is presented. For dynamic problems having responses dominated by high frequency modes, such as those with impact, explosive, traveling and earthquake loads high gradient stress regions change their locations from time to time. And the time step size may need to vary in order to deal with whole process ranging from transient phase to steady state phase. As the sizes of elements in space vary in different regions, the procedure also permits different time stepping. In such a way, the best performance attainable by the finite element method can be achieved. In this study, we estimate both of the kinetic energy error and stran energy error induced by spatial and time discretization in a consistent manner. Numerical examples are used to demonstrate the performance of the procedure.

• Journal of Mechanical Science and Technology
• /
• 제18권4호
• /
• pp.560-572
• /
• 2004

Aeroelastic response and control of airfoil-flap system exposed to sonic-boom, blast and gust loads in an incompressible subsonic flowfield are addressed. Analytical analysis and pertinent numerical simulations of the aeroelastic response of 3-DOF airfoil featuring plunging-pitching-flapping coupled motion subjected to gust and explosive pressures in terms of important characteristic parameters specifying configuration envelope are presented. The comparisons of uncontrolled aeroelastic response with controlled one of the wing obtained by feedback control methodology are supplied, which is implemented through the flap torque to suppress the flutter instability and enhance the subcritical aeroelastic response to time-dependent excitations.