• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.194-201
• /
• 2014

To increase the capacity of secondary cells, an appropriate serial composition of the battery modules is essential. The unbalance that may occur due to the series connection in such a serial composition is the main cause for declines in the efficiency and performance of batteries. Various studies have been conducted on the use of a passive or active topology to eliminate the unbalance from the series circuit of battery modules. Most topologies consist of a complex structure in which the Battery Management System (BMS) detects the voltage of each module and establishes the voltage balancing in the independent electrical power converters installed on each module by comparing the module voltage. This study proposes a new magnetic flux sharing type DC/DC converter topology in order to remove voltage unbalances from batteries. The proposed topology is characterized by a design in which all of the DC/DC convertor outputs connected to the modules converge into a single transformer. In this structure, by taking a form in which all of the battery balancing type converters share magnetic flux through a single harmonic wave transformer, all of the converter voltages automatically converge to the same voltage. This paper attempts to analyze the dynamic properties of the proposed circuit by using a Programmable Synthesizer Interface Module (PSIM), which is useful for power electronics analysis, while also attempting to demonstrate the validity of the proposed circuit through experimental results.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.1
• /
• pp.66-72
• /
• 2006

This article presents the optimal operation of an air conditioner using thermoelectric modules. A prototype of air conditioner using four thermoelectric modules has been designed and built. The system performance with evaporative cooling for hot side of the module are studied in detail for several operating parameters, such as input power to the thermoelectric module, fans and pump. It is found that the optimal input voltage to the thermoelectric module and pump is selected for the best system performance based on the cooling capacity and the COP at a given operating condition. It is also found that both the cooling capacity and COP of a system is increased with an increase in the input power to fans. The cooling performance could be improved when the ambient temperature is increased and the relative humidity is decreased since the evaporative cooling at the hot side has been increased.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.11 no.4
• /
• pp.302-306
• /
• 2001

Because face Images have many variations(expression, illumination, orientation of face, etc), there has been no popular method which has high recognition rate. To solve this difficulty, data fusion that fuses various information has been studied. But previous research for data fusion fused additional biological informationUingerplint, voice, del with face image. In this paper, cooperative results from several face image recognition modules are fused without using additional biological information. To fuse results from individual face image recognition modules, we use re-defined mass function based on Dempster-Shafer s fusion theory.Experimental results from fusing several face recognition modules are presented, to show that proposed fusion model has better performance than single face recognition module without using additional biological information.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.1012-1016
• /
• 2002

This paper describes a research work of developing computer-aided design of a product with bending and piercing for progressive working. An approach to the system for progressive working is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in Auto-LISP on the Auto-CAD with a personal computer and is composed of four main modules, which are input and shape treatment, flat pattern layout, strip layout, and die layout modules. The system is designed by considering several factors, such as bending sequences by fuzzy set theory, complexities of blank geometry, punch profiles, and the availability of a press equipment. Strip layout drawing generated in the strip layout module is presented in 3-D graphic forms, including bending sequences and piercing processes with punch profiles divided into for external area. The die layout module carries out die design for each process obtained from the results of the strip layout. Results obtained using the modules enable the manufacturer for progressive working of electric products to be more efficient in this field.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.137-146
• /
• 2005

This paper describes a research work to develop a computer-aided design for the product made by progressive working of bending and piercing. An approach to the system for progressive working is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer and is composed of three main modules, which are input and shape treatment, flat pattern layout, strip layout modules. The system is designed by considering several factors, such as piercing and bending sequences by fuzzy set theory, complexities of blank geometry, punch profiles, and the availability of a press equipment. Strip layout drawing generated in the strip layout module is presented in 3-D graphic forms, including piercing and bending sequences with punch profiles divided into for external area. Results obtained using the modules enable the manufacturer for progressive working of electric products to be more efficient in this field.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1519-1528
• /
• 2017

The paper proposes a well structured, component count waned single phase multilevel inverter (MLI) topology, which drives three different modules viz. Stipulation Based Sources Insertion (SBSI) module, Level Count Increasing (LCI) module and Inter-Linking H-Bridge (ILHB) module. The SBSI module confronts the number of basic sources needed in series/parallel to achieve required magnitude for any particular level. The LCI possesses an offsetting dc source and opuses to increase the number of levels and the ILHB module links the SBSI and LCI modules. A developed Hybrid Pulse Width Modulation (HPWM) strategy has PWM pulses for the switches of LCI module while the switches of the remaining two modules function at fundamental switching frequency. A fifteen level version of the proposed stipulation based sources insertion MLI (SBSIMLI) topology is simulated in MATLAB R2010a and a prototype of the similar specifications is constructed to validate the performance by experimental results. The comparison between the developed SBSIMLI topology and the competent topologies shows many interesting facts.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1109-1118
• /
• 2014

A Fundamental Frequency Sorting Algorithm (FFSA) is proposed in this paper to balance the voltages of floating dc capacitors for Modular Multilevel Converters (MMCs). The main idea is to change the sequences of the CPS-PWM carriers according to the capacitor voltage increments during the previous fundamental period. Excessive frequent sorting is avoided and many calculating resources are saved for the controller. As a result, more sub-modules can be dealt with. Furthermore, it does not need to measure the arm currents. Therefore, the communication between the controllers can be simplified and the number of current sensors can be reduced. Moreover, the proposed balancing method guarantees that all of the switching frequencies of the sub-modules are equal to each other. This is quite beneficial for the thermal design of the sub-modules and the lifetime of the power switches. Simulation and experimental results acquired from a 9-level prototype verify the viability of the proposed balancing method.

• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.15 no.1
• /
• pp.14-21
• /
• 2008

Purpose: Objective Structured Clinical Examination(OSCE) has been used for clinical skill evaluation. This study was done investigate whether there are positive impact educational effects if nursing students are invited to develop OSCE modules. Method: The participants were 63 second-year students in one nursing college. Students were divided into 3 groups; the OSCE module development group(Exp1), traditional study group(Exp2), and control group(Cnt). Students were allocated according to clinical skill test scores to make the 3 groups equal. Exp1 developed OSCE modules, and Exp2 studied using traditional methods. Clinical skill tests and surveys were done to measure self-directed readiness, problem-solving ability, and self-efficacy before and after experimental treatments. Results: Clinical skill test scores increased significantly in all three groups, but Exp1 and Exp2 showed a higher clinical skill test score increment than Cnt. Self-directed readiness scores increased significantly in Exp1, but not in Exp2 and Cnt. Problem-solving ability scores increased significantly in Exp1 compared to Cont. Conclusion: Development of OSCE modules has positive educational effects for participating students in terms of clinical skill tests, self-directed readiness, and problem-solving ability.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.735-739
• /
• 2001

This paper describes a research work of developing computer-aided design of a product with bending and piercing for progressive working. An approach to the system for progressive working os based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theorise, experimental results and the empirical knowledge of field experts. the system has been written in AutoLISP on the AutoCAD with a personal computer and is composed of three main modules, which are input and shape treatment, flat pattern layout and strip layout modules. Strip layout of the system is designed by using fuzzy set theory. Process planning is determinated by fuzzy value according to several rules. Strip layout drawing generated in strip layout module is presented in 3-D graphic forms, including bending sequences and piercing processes with punch profiles divided into for external area. Results obtained using the modules enable the manufacturer for progressive working of electric products to be more efficient in this field.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.12
• /
• pp.55-64
• /
• 2008

This paper describes a research work of developing an automated progressive design system for manufacturing the product with multi processes such as piercing, bending, and deep drawing. An approach to the system for progressive working is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system consists of three main modules, which are shape treatment, strip layout, and die layout modules. Based on knowledge-based rules, the system is designed considering several factors, such as material and thickness of a product, piercing, bending and deep drawing sequence, and the complexities of the blank geometry and punch profiles. It generates the strip layout drawing for an automobile product. Die design for each process is carried out through the die layout module from the results of the strip layout module. Results obtained using the modules enable the designers for manufacturing products with multi processes to be more efficient in this field.