• KIEE International Transactions on Power Engineering
• /
• v.4A no.3
• /
• pp.129-133
• /
• 2004

This paper deals with the design and implementation of a TCSC (Thyristor Controlled Series Capacitor) simulator, which is a module for an analog type power system simulator. Principally, it presents configuration of controller hardware/software and its experimental results. An analog type power system simulator consists of numerous power system components, such as various types of generator models, scale-downed transmission line modules, transformer models, switches and FACTS (Flexible AC Transmission System) devices. It has been utilized for the verification of the control algorithm and the study of system characteristics analysis. This TCSC simulator is designed for 50% line compensation rate and considered for damping resister characteristic analysis. Its power rate is three phase 380V 20kVA. For hardware extendibility, its controller is designed with VMEBUS and its main CPU is TMS320C32 DSP (Digital Signal Processor). For real time control and communications, its controller is applied to the RTOS (Real Time Operation System) for multi-tasking. This RTOS is uC/OS-II. The experimental results of capacitive mode and inductive mode operations verify the fundamental operations of the TCSC.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.4
• /
• pp.260-265
• /
• 2008

The excess heat that is generated from PV modules can be removed and converted into useful thermal energy. A photovoltaic/thermal (PVT) module is a combination of photovoltaic module with a solar thermal collector, forming one device that converts solar radiation into electricity and heat simultaneously. In general, two types of PVT can be distinguished : glass-covered PVT module, which produces high-temperature heat but has a slightly lower electrical yield, and uncovered PVT module, which produces relatively low-temperature heat but has a somewhat higher electrical performance. In this paper, the experimental performance of water type PVT combined module, glass-covered, analyzed. The electrical and thermal performance of the module were measured in outdoor conditions, and the results are analyzed. The results showed that the thermal efficiency of the PVT module was 27.6% average and its PV efficiency was about 10.0% average, both depending on solar radiation, inlet water temperature and ambient temperature.

• Membrane Journal
• /
• v.14 no.1
• /
• pp.18-25
• /
• 2004

The purpose of this paper was to find out the proper equation to predict the gas transfer rate for designing intravenous artificial lung assist device. The prepared hollow fiber modules were examined under various experimental conditions through experimental modeling before inserted the artificial lung assist d $\varepsilon$ vice into as venous. As a result, we can estimate the gas transfer as a function of the packing density. The gas transfer obtained from the experiment was similar to that from the equation, confirming the usefulness equation. Therefore, we can conclude the gas transfer of the intravenous artificial lung assist device as a function of the packing density, and this functions are very useful for predicting the gas transfer of the intravenous artificial lung assist device.

• Journal of the Korean Society for Library and Information Science
• /
• v.21
• /
• pp.249-290
• /
• 1991

Theoretical developments in the information retrieval have offered a number of alternatives to traditional Boolean retrieval. Probability theory and fuzzy set theory have played prominent roles here. Fuzzy set theory is an attempt to generalize traditional set theory by permitting partial membership in a set and this means recognizing different degrees to which a document can match a request. In this study, an experimentation of a document retrieval system using the fuzzy relation matrix of the keywords is described and the results are offered. The queries composed of keywords and Boolean operaters AND, OR, NOT were processed in the retrieval method, and the method was implemented on the PC of 32bit level (30 MHz) in an experimental system. The measurement of the recall ratio and precision ratio verified the effectiveness of the proposed fuzzy relation matrix of keywords and retrieval method. Compared to traditional crisp method in the same document database, the recall ratio increased $10\%$ high although the precision ratio decreased slightly. The problems, in this experiment, to be resolved are first, the design of the automatic data input and fuzzy indexing modules, through which the system . can have the ability of competition and usefulness. Second, devising a systematic procedure for assigning fuzzy weights to keywords in documents and in queries.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.3
• /
• pp.107-113
• /
• 2013

In this study, three different types of experimental models of BIPV curtain wall units with GIGS modules were built, and their thermal and electrical performances were analyzed. The experimental results showed that the temperature of the rear side of the GIGS module with the application of an insulation in the curtain wall spandrels was higher than a GIGS module standalone by $22^{\circ}C$, which results in a reduction in the power generation of the former by 8 %. On the other hand, when ventilation was applied to the model to improve the power generation performance, the module temperature was observed to be $142^{\circ}C$ lower compared to the enclosed type, and the power generation performance improved by 5 %. It confirmed that the temperature increase in the rear side of the GIGS module with insulation layer reduced the electrical performance of the module. Based on this, it is claimed that providing sufficient ventilation at the GIGS applied spandrels contribute to improve the power generation of the GIGS module.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.4
• /
• pp.22-25
• /
• 2006

This paper deals with the computation of the current limiting behavior of high-temperature superconducting (HTS) modules for the superconducting fault current limiter (SFCL). The SFCL module consists of a monofilar type BSCCO-2212 tube and a shunt coil made of copper or brass. The shunt coil is connected to the monofilar superconducting tube in parallel. Through analysis of the quench behavior of the monofilar component with shunt coils, it is achieved to drive an equivalent circuit equation from the experimental circuit structure. In order to analyze the quench behavior of the SFCL module, we derived a partial differential equation technique. Inductance of the monofilar component and the impedance of the shunt coil are calculated by Bio-Savart and Ohm's formula, respectively. We computed the quench behavior using the calculated values, and compared the results with experimental results for the quench characteristics of a component. The results of computation and test agreed well each other, and it was concluded that the analytic result could be applied effectively to design of the distribution-level SFCL system.

• Journal of Forest and Environmental Science
• /
• v.16 no.1
• /
• pp.119-123
• /
• 2000

This paper studies the methods to support decision making for forest management Using GIS. Specially, most important is selecting restrict area to timber harvest suitable on scheduling its harvest in experimental forest of kangwon national university. Because timber harvesting causes water pollution, land sliding and soil erosion, it is necessary to restrict area to be harvest. The study is analyzed with Buffering modules and overlay modules which are an function of Arcinfo 7.1. As a result, restricted area is 52.64ha in total area. Of which Hardwood stand 13.21ha, pinus Pinus koraiensis stand 26.44ha, Larix leptolepis stand 12.38ha and Pinus rigida stand 0.61ha.

• Journal of Digital Contents Society
• /
• v.18 no.6
• /
• pp.1135-1142
• /
• 2017

In this paper, we propose IoT based smart CCTV security service to prevent crime in blind spot and prevent unexpected fire or danger. In the proposed method, a RC (Radio Control) car is made using Raspberry pie, and a camera and various modules are installed in an RC car. It was then implemented using Raspbian O / S, Apache Web Server, Shell script, Python, PHP, HTML, CSS, Javascript. The RC car provides a security service that informs the manager of the situation by judging the risk of the scene with modules such as video, voice and temperature. Experimental results show that the transmission time of video and audio information is less than 0.1 second. In addition, real-time status transmission was possible in AVG, emergency, and manual mode. It is expected that the proposed method will be applied to the development of smart city by applying it to unmanned vehicles, drones and the like.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.2 s.308
• /
• pp.65-72
• /
• 2006

The traffic lights detection and recognition system is an essential module of the driver warning and assistance system. A method which is a color vision-based real time detection and recognition of traffic lights is presented in this paper This method has four main modules : traffic signals lights detection module, traffic lights boundary candidate determination module, boundary detection module and recognition module. In traffic signals lights detection module and boundary detection module, the color thresholding and the subtraction value of saturation and intensity in HSI color space and detection probability mask for lights detection are used to segment the image. In traffic lights boundary candidate determination module, the detection mask of traffic lights boundary is proposed. For the recognition module, the AND operator is applied to the results of two detection modules. The input data for this method is the color image sequence taken from a moving vehicle by a color video camera. The recorded image data was transformed by zooming function of the camera. And traffic lights detection and recognition experimental results was presented in this zoomed image sequence.

• Journal of Broadcast Engineering
• /
• v.16 no.4
• /
• pp.602-613
• /
• 2011

In this paper, we propose a hybrid stereoscopic camera system which acquires and utilizes stereoscopic images from two different camera modules, the main-camera module and the sub-camera module. Hybrid stereoscopic camera can effectively reduce the price and the size of a stereoscopic camera by using a relatively small and cheap sub-camera module such as a mobile phone camera. Images from the two different camera modules are very different from each other in aspects of color, angle of view, scale, resolution and so on. The proposed system performs an efficient hybrid stereoscopic image registration algorithm that transforms hybrid stereoscopic images into normal stereoscopic images based-on camera geometry. As experimental results, the registered stereoscopic images and applications of the proposed system are shown to demonstrate the performance and the functionality of the proposed camera system.