• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.94-100
• /
• 1999

The friction and wear behavior of MoS$_2$Coatings were investigated using a pin and disk type tester. The experiment was conducted using silicon nitride as pin material and MoS$_2$-on-bearing steel as disk material under different operating conditions that include linear sliding speeds in the range of 22~66mm/sec, normal loads varying from 9.8~29.4N, corresponding to maximum contact pressure of 1.78~2.830GPa and atmospheric conditions of high vacuum, medium vacuum, ambient air. The results showed that low friction coefficient of the coating has been identified when running in high vacuum and that friction coefficient and wear volume increased with increasing normal load. Also at high load conditions, the friction coefficient and wear volume increased with increasing sliding velocity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.431-434
• /
• 2005

MTS(Monobloc Tube Shaft) has been used for the reduction in weight of shaft and increase in supply of power in the auto industry nowadays. Cold drawing process having high productivity and reduction in the cost has been regarded as the effective technology that is able to substitute for swaging process as forming MTS with constant outer diameter or hollow shaft without surface defects. The objective of this study is not only to find out the optimal process conditions understanding the effect of process parameters on carrying out cold drawing process of SIS(Steering Input Shaft) but also to control the defects resulted from inappropriate process conditions. Therefore, the proper drawing conditions are presented using FE-Analysis and experiment in the paper.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.3
• /
• pp.122-135
• /
• 2014

This paper was studied on the horizontal continuous casting of Al-xSi(x=10~15%) aluminum alloy. The experiments of the horizontal continuous casting was carried out by the horizontal continuous casting machine for various casting conditions and investigated on fracture types and mechanisms. Surface defect types for the horizontal continuous casting is also investigated. And the study was carried out that the horizontal continuous casting conditions such as casting temperature, cooling rate, and drawing speed affect the hardness and primary silicon size of Al-xSi(x=10~15%) aluminum rod bar. Casting temperature within this experiment conditions don't affect on the hardness of rod bar but the higher casting temperature is the smaller primary silicon size. The higher cooling rate and drawing speed have the higher hardness and the smaller primary silicon size.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.115-119
• /
• 2008

Weld line in injection molded part is one of the defects in injection molding process. Weld line deteriorates not only appearance quality but mechanical property. In this study, ABS and PP were used as experimental materials. And weld line length, depth and strength have been examined according to the injection molding conditions. As the results of experimental studies, weld line length increased as flow rate increases for all materials. And the flow rate is most influenced to the creation of weld line length. Also weld line strength increased, as flow rate and melt temperature increase for all materials. The whole experiment results was similar to CAE analysis results.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.3
• /
• pp.284-289
• /
• 2003

In this study, the prediction on the quality of tools after coating process has been investigated. Under different coating conditions, cutting resistances have been obtained and analyzed with a tool dynamometer to provide optimized coating conditions. The optimized coating conditions Lhave been computed with the most effective factors found by S/N ratio of Taguchi method. To evaluate the influence of the factors on cutting efficiency through the minimum of number of experiment times, the way of neural network design using Taguchi method has been employed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.197-198
• /
• 2019

The aim of the research is evaluating the feasibility of inspection for early age frozen damage and for expansion of concrete under the various time periods of -20℃ temperature condition. When the concrete samples were exposed for 12 hours and 24 hours, the frozen depth of the concrete were 10 and 60 mm, respectively, under the wet conditions. From the experiment results of temperature and expansion, only surface area suffered frozen damage for 12 hours exposing conditions while entire area suffered frozen damage for 24 hours exposing conditions.

• Fashion & Textile Research Journal
• /
• v.7 no.5
• /
• pp.542-546
• /
• 2005

This study was investigated to establish the optimum conditions of dyeing silk fabric with Brassica campestris. This experiment was done under different dyeing conditions of dye concentration, dyeing temperature, dyeing time, dyeing repeating times, and mordants which were treated pre, syn, and post methods. The effects of dyeing conditions and mordanting were evaluated in terms of dyeaffinity(K/S value) and CIE-Lab color factors. Also, the effect of mordanting on color fastnesses was assessed. The dyeaffinity increased remarkably as dye concentration increased up to 200% owf. The dyeaffinity increased continuously with dyed temperature and reached dyeing equilibrium at $80^{\circ}C$. The maximum dyeaffinity was observed at 30minutes of dyeing time. In the relationship between the K/S value and dyeing repeating times, the K/S value became higher as repeating time was increased. The changes of surface color and colorfatness of dyes were not increased greatly on all mordanting states. The extracts of Brassica campestris produced mainly yellow color in silk fabric. The antimicrobial activity existed slightly as the ratio of 22.7%.

• Journal of Hydrogen and New Energy
• /
• v.21 no.5
• /
• pp.398-404
• /
• 2010

Process conditions for MEA fabrications have significant effects on properties and performance of the MEAs for PEMFCs. In this study, effects of additives on the surface properties of the MEA was investigated to improve homogeneity of the coated catalyst layer. Another parameter that affects on characteristics of the MEAs is hot-pressing condition. Hot pressing condition was optimized by using DOE (design of experiment) method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.80-84
• /
• 1997

In this experiment, A1$_2$O$_3$ thick films were prepared by electrophoretic method using A1$_2$O$_3$ fine Powder of which composition were FA-5-500 and FA-5-900. The growth behavior of A1$_2$O$_3$ thick films were characterized as preparation conditions, such as applied voltage, deposition time and adding conditions. As a result, A1$_2$O$_3$ thick films were successfully fabricated by electrophoretic method on molybdnum plate in which etanol and distilled used were used as a solvent. Deposition conditions for good uniformity of the A1$_2$O$_3$ thick films were applied voltage of 60volts, deposition time of 2 seconds, heat treatment at 1$700^{\circ}C$ for 5 minutes.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1359-1361
• /
• 2003

As the maximum power operating point(MPOP) of Photovoltaic(PV) power generation systems changes with changing atmospheric conditions such as solar radiation and temperature, an important consideration. In the design of efficient PV system is to track the MPOP correctly. Many maximum power point tracking(MPPT) techniques have been considered in the past, however, techniques using microprocessors with appropriate MPPT algorithms are favored because of their flexibility and compatibility with different PV arrays. Although the efficiency of these MPPT algorithms is usually high, it drops noticeably in case of rapidly changing atmospheric conditions. This pager proposed a new MPPT algorithm based on perturb & observe(P&O) algorithm with experiment. The results shows that the new P&O algorithm has successfully tracked the MPOP, even in case of rapidly changing atmospheric conditions, and has higher efficiency than ordinary algorithms.