• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.5
• /
• pp.231-239
• /
• 2014

This paper represents a method of existing building energy simulation using energy audit data. Energy audit must be carried out for reasonable analysis, because characteristics of existing buildings such as efficiency of fan, pump, flow rate, pressure, COP and operating schedule could be changed during the building operation. These building characteristics should be measured to estimate actual energy consumption of the existing building. In this study, we conducted energy audit and calculated energy savings for a 7-stories building as a case-study. The energy audit data were used to calibrate the building model of EnergyPlus simulation. Baseline model validated according to M&V guideline index. As a result, building characteristics are significant parameters making a big impact on energy savings in existing buildings.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6D
• /
• pp.961-968
• /
• 2006

Curbs and L-type gutters installed at the edge of a road are very important structures to protect pedestrians from traffic accidents and to restraint slip of cars due to rain. However, existing construction method where great parts of the construction progress are done by human power has many problems in workability, quality and cost etc. In this paper, a new construction method for improvement in workability and quality for curbs and L-type gutters is developed. In order to investigate the structural safety and quality of curbs and gutters installed by the new method, tensile and lateral load tests are performed on curbs installed by existing and new methods and uniaxial compression tests are also performed on concrete samples of gutters constructed by existing and new methods. The test results show that the alignment of curbs and the strength of gutter concrete are very much improved by applying the new method. The tensile and lateral load capacities of the curbs installed by the new method are 10.7 and 2.5 times higher than those of curbs by existing method, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3482-3486
• /
• 2013

In the case of the Pilot Symbol Assisted Modulation (PSAM) method predicting and compensating amplitude and phases caused on fading channels, there can be severe performance deterioration by Doppler spread on fast fading channels. In this paper, the fading compensation method suggested so as to improve occurring problems as well as analyze them. Doppler spread is the major cause of the bit error rate(BER) performance deterioration. Compared to the existing PSAM method, the more performance deterioration occurs, the larger Doppler spread appears but performance shows well its less $10^{-2}BER$ performance than the existing PSAM method in the suggested method whereas the existing PSAM method has about $10^{-1}BER$ its considerable performance deterioration that caused by Doppler spread within a symbol cycle with the level of delay wave interference.

• The KIPS Transactions:PartD
• /
• v.17D no.4
• /
• pp.245-252
• /
• 2010

In this paper, we propose an effective filtering method for skyline queries in mobile ad hoc networks (MANETs). Most existing researches assume that data is uniformly distributed. Under these assumptions, the previous works focus on optimizing the energy consumption due to the limited battery power. However, in practice, data distribution is skewed in a specific region. In order to reduce the energy consumption, we propose a new filtering method considering the data distribution. We verify the performance of the proposed method through a comparative experiment with an existing method. The results of the experiment confirm that the proposed method reduces the communication overhead and execution time compared to an existing method.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.52 no.7
• /
• pp.429-436
• /
• 2003

This paper presents a new approach for evaluating the transmission marginal loss factors (MLFs) considering the reactive power. Generally, MLFs are represented as the sensitivity of transmission losses, which is computed from the change of the generation at reference bus by the change of the load at the arbitrary bus-i. The conventional evaluation method for MLFs uses the only H matrix, which is a part of jacobian matrix. Therefore, the MLFs computed by the existing method, don't consider the effect of the reactive power, although the transmission losses are a function of the reactive power as well as the active power. To compensate the limits of the existing method for evaluating MLFs, the power factor at the bus-i is introduced for reflecting the effect of the reactive power in the evaluation method of the MLFs. Also, MLFs calculated by the developed method are applied to energy spot markets to reflect the impacts of reactive power. This method is tested with the sample system with 5-bus, and analyzed how much MLFs have an effect on the bidding/offer price, market clearing price(MCP), and settlement in the competitive energy spot market. This paper compared the results of MLFs calculated by the existing and proposed method for the IEEE 14-bus system, and the KEPCO system.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.2
• /
• pp.61-66
• /
• 2005

This paper presents a refined protection algorithm of the unfused 22.9kV shunt capacitor banks in grounded wye connection to improve the existing algorithm using the voltage difference method. It is difficult to detect ground faults with arc near the input points or ground faults near the grounding point by the existing algorithm using only the voltage balanced relay. This paper shows that ground faults with arc near the input point can be detected by harmonics analysis of the differential voltage and that it has no impact of harmonics out of nonlinear loads which have the quantitative influence on capacitor banks. Thus the proposed method using harmonics analysis can be a proper detection method. In case of ground faults near the grounding point, an OVGR is being added recently and its validity is verified in this paper. The proposed method is applied to a 22.9kV example system and is verified that the proposed algorithm can detect clearly faults which are not easy to detect by the existing method.

• Structural Engineering and Mechanics
• /
• v.9 no.5
• /
• pp.469-482
• /
• 2000

A numerical study using nonlinear finite element analysis is performed to investigate the behavior of isolated reinforced concrete walls subjected to combined axial force and in-plane and out-of-plane bending moments. For a nonlinear finite element analysis, a computer program addressing material and geometric nonlinearities was developed. Through numerical studies, the internal force distribution in the cross-section is idealized, and then a new design method, different from the existing methods based on the plane section hypothesis was developed. According to the proposed method, variations in the interaction curve of the in-plane bending moment and axial force depends on the range of the permissible axial force per unit length, that is determined by a given amount of out-of-plane bending moment. As the out-of-plane bending moment increases, the interaction curve shrinks, indicating a decrease in the ultimate strength. The proposed method is then compared with an existing method, using the plane section hypothesis. Compared with the proposed method, the existing method overestimates the ultimate strength for the walls subjected to low out-of-plane bending moments, while it underestimates the ultimate strength for walls subject to high out-of-plane bending moments. The proposed method can address the out-of-plane local behavior of the individual wall segments that may govern the ultimate strength of the entire wall.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.8
• /
• pp.1418-1425
• /
• 2003

In CAD systems, a surface to be machined is expressed by a series of curves, such as B-spline, Bezier and NURBS curves, which compose the surface and then in CAM systems the curves are divided into a large number of line or arc segments. These divided movement commands, however, cause many problems including their excessive size of NC data that makes almost impossible local adjustment or modification of the surface. To cope with those problems, the necessity of real-time curve or surface interpolators was embossed. This paper presents an efficient real-time tool-path generation method fur interpolation of NURBS surfaces in CNC machining. The proposed tool-path generation method is based on an improved iso-scallop strategy and can provide better precision than the existing methods. The proposed method is designed such that tool-path planning is easily managed in real-time. It proposed a new algorithm for regulation of a scallop height, which can efficiently generate tool-paths and can save machining time compared with the existing method. Through computer simulations, the performance of the proposed method is analyzed and compared with the existing method in terms of federate, total machining time and a degree of constraint on the scallop height.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.11 no.4
• /
• pp.69-79
• /
• 2015

This research proposes a modified data hiding method to hide data in a slack space of an NTFS index record. The existing data hiding method is for anti-forensics, which uses traces of file names of an index entry in an index record when files are deleted in a direcotry. The proposed method in this paper modifies the existing method to make non-admittable ASCII characters for a file name applicable. By improving the existing method, problems of a file creation error due to non-admittable characters are remedied; including the non-admittable 9 characters (i. e. slash /, colon :, greater than >, less than <, question mark ?, back slash ${\backslash}$, vertical bar |, semi-colon ;, esterisk * ), reserved file names(i. e. CON, PRN, AUX, NUL, COM1~COM9, LPT1~LPT9) and two non-admittable characters for an ending character of the file name(i. e. space and dot). Two results of the two message with non-admittable ASCII characters by keyboard inputs show the applicability of the proposed method.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.2
• /
• pp.76-81
• /
• 2021

This study proposes a method to reduce the phase error of the received signal to detect the object bearing. The phase shift of the received signal occurs due to the multipath of the signal by natural structure or artificial structures. When detecting the direction of the object using radio waves, the phase of the received signal cannot be accurately detected because of the phase bearing error in the object detection direction. The object detection direction estimation depends on the phase difference, antenna installation distance, signal source wavelength, frequency band and bearing angle. This study reduces the error of the phase bearing by using the phase delay of the relative phase difference for the signals incident on the two antennas. Through simulation, we analyzed the object direction detection performance of the proposed method and the existing method. Three targets are detected from the [-15°, 0°, 15°] direction. The existing method detects the target at [-13°, 3°, 17°], and the proposed method detects the at [-15°, 0°, 15°]. As a result of the simulation, the target detection direction of the proposed method is improved by 2 degrees compared to the existing method.