• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.762-767
• /
• 2001

We report the white light emission from the multilayer organic electroluminescent(EL) device using exciplex emission. The exciplex at 500nm originated between poly(N-vinylcarvazole)(PVK) and 2,5-bis(5'-tert-butyl-2-benzoxazoly)thiophene(BBOT) and exciplex of 50nm originated from N,N'-diphenyl-N,N'-(3-methyphenyl)-1,1'-biphenyl-4,4'-diamine(TPD) and BBOT were observed. Also, the energy transfer from PVK to BBOT and poly(3-hexylthiophene)(P3HT) in mixed emitting materials was occurred. The electroluminescence(EL) spectra of organic EL device which have a device structure of ITO/CuPc(5nm)/emitting layer(100nm)/BBOT(30nm)/LiF(1.4nm)/Al(200nm) were slightly changed as a function of the applied voltage. The luminance fo 12.3 ${\mu}$W/$\textrm{cm}^2$ was achieved at 20V and EL spectrum measured at 20V corresponds to Commission Internationale de L\`Eclairage(CIE) coordinates of x=0.29 and y=0.353.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2373-2385
• /
• 1995

The goals of this study are to apply exciplex method to the visualization of the fuel spray of a diesel engine and to investigate the liquid phase of fuel spray that injected at the various tips of a fuel injector. This study provides the informations for the improvement of the diesel injection system and the structures of diesel spry with the boiling of fuel droplets in combustion chamber by the exciplex method. Hexame was used as fuel for approximation to injection condition of the engine. And naphthalene and TMDP were added to the fuel for the visualization by exciplex method. Experimental injectors were 4hole, 8hole, and 1hole impinging injectors. In the injection condition of actual engine the exciplex was sufficient to catch the liquid phase signal. The spray penetration of impinging injector was small than that of actual 4 and 8hole injector but atomization was better. The upper bound of impinging injector was determined by the geometry of a cylinder head and the lower bound was determined by spray angle. On impinging injector the atomization was better at the edge of disk than at center of disk and also the mixing with environmental gas was better.

• Journal of Environmental Science International
• /
• v.27 no.6
• /
• pp.437-445
• /
• 2018

Laser induced-exciplex-fluorescence (EXCIPLEX) proposed by Melton is used to visualize fuel vapor in spray combustion. However, in the EXCIPLEX method based on TMPD/naphthalene system, the TMPD : naphthalene ratio is strictly restricted to 1 : 9. In addition, fluorescence intensity due to the vapor phase is extremely weak. To overcome these drawbacks, we propose a new laser-induced-excimer fluorescence (EXCIMER) method to visualize the liquid and vapor phases simultaneously. The spatial distributions of liquid and vapor in fuel spray suspended by ultrasonic waves are compared using the EXCIPLEX and EXCIMER methods. The correlation between fuel vapor concentration and fluorescence intensity is experimentally investigated by measuring the fluorescence intensity of saturated vapor formed over liquid fuel at a controlled temperature. These experimental results indicate that the EXCIMER method is effective for evaluating fuel vapor visualization in spray combustion. Furthermore, the quantitative distribution of fuel vapor concentration can be correctly estimated by the EXCIMER method.

• Journal of ILASS-Korea
• /
• v.4 no.4
• /
• pp.1-8
• /
• 1999

The concentration and spatial distribution of vapor phases in DI (Direct Injection) gasoline spray were measured quantitatively by exciplex fluorescence method. Fluorobenzene and DEMA (diethylmethylamine) in a solution of hexane were used as the exciplex-forming dopants. The fluorescence intensity of vapor phase were obtained by ICCD camera with the appropriate filter The relationship between fluorescence intensity and vapor concentration was induced fer the purpose of a quantitative analysis. The 2-D vapor/liquid images of fuel spray were captured under the evaporation condition, and the spatial distribution of vapor concentration was obtained. The spatial distribution of liquid phase had hollow-cone shape. And the vapor phase was widely distributed in the whole spray. The behavior of vapor phase was significantly affected by second flow such as entrainment, vortex, while that of liquid phase was scarcely affected.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.50-58
• /
• 2001

The purpose of this research is to obtain the information of the development process of a vaporizing GDI spray using exciplex fluorecence method. Fluorobenzene/DEMA system was used as the exciplex-forming dopants. The 2-D spray images of liquid and vapor phases were acquired, and the behavior of both phases was analyzed by the image processing. The experiment was performed at the three different ambient perssures and the ambient temperature of 273K and 473K. As the result of this work, it was found that the development characteristics of GDI spray have stronger effect on the ambient pressure than on the ambient temperature. With an increase of ambient pressure, the distribution of vapor phase was decreased and the concentration of that was denser. Two regions, namely cone and mixing regions could be identified from those resulrs.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.3
• /
• pp.189-197
• /
• 2002

The color stability and purity from OLED is of current interest. Aggregation of dyes alters the device color after fabrication of the devices. Exciplex and electroplex formations have been proposed to explain the aggregate color change. We investigate the possibility of exciplex formation and propose the new electroplex state that can cause the bathochromic shift of the electroluminescence spectrum from the devices with TPD/PBD layers. The photoluminescence maximum of the device was 420nm, and the electroluminescence maximum of the device to became 480nm. The bathochromic shift cannot be attained with photoluminescence study with highly concentrated TPD/PBD mixture. This clearly indicates that the 480nm spectrum of the devices is not resulted from the exciplex formation with TPD and PBD. We observed the overshoot in EL spectrum from the OLEDs. The most intense overshoot was observed at 460nm, which may be due to the aggregates that are formed after the electric field has been removed from the devices.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.5
• /
• pp.688-696
• /
• 2001

Vaporizing characteristics of two GDI injectors with different spray angles were investigated using exciplex fluorescence method. Injector I has narrower spray angle, while injector II has wider one. The exciplex system of fluorobenzene and DEMA in a non-fluorescing base fuel of hexane was employed. In quantifying concentration of fuel vapor, quenching of concentration and temperature was corrected. Droplet size and velocity were also measured by PDPA under non-vaporizing condition. From obtaining the images of liquid and vapor phases, vaporizing GDI sprays could be divided as two regions: cone and mixing regions. For injector I, vortex region was not developed. High concentration of fuel vapor due to vaporization of many fine droplets was distributed near the spray axis. For injector II, droplets with the diameter of about 10 $\mu$m were distributed in the vortex region. The vortex region had high concentration of fuel vapor due to vaporization of these droplets. Particularly, higher and lower concentrations of fuel vapor were balanced at 2ms after the start of injection for injector II.

• Journal of Mechanical Science and Technology
• /
• v.17 no.1
• /
• pp.157-167
• /
• 2003

The exciplex fluorescence technique with the TMPD (tetamethyl-Ρ-phenylene-diamine) / naphthalene dopant system was applied in a combustion-type constant-volume spray chamber. A detailed set of calibration experiments has been performed in order to quantify the TMPD fluorescence signal. It has been demonstrated that the TMPD fluorescence intensity was directly proportional to concentration, was independent of the chamber pressure, and was not sensitive to quenching by either water vapor or carbon dioxide. Using a dual heated-jet experiment, the temperature dependence of TMPD fluorescence up to 1000 K was measured. The temperature field in the spray images was determined using a simple mixing model, and an iterative solution method was used to determine the concentration and temperature field including the additional effects of the laser sheet extinction. The integrated fuel vapor concentration compared favorably with the measured amount of injected fuel when all of the liquid fuel had evaporated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.762-765
• /
• 2002

The bilayer organic light-emitting diode using Al (DBM) $_3$ (DBM=Dibenzoylmethane) as an emitting material and poly (N-vinylcarbazole) (PVK) as hole-transport material, emitted bright blue-green light instead of blue light. The blue-green emission is attributed to exciplex formation at the solid interface between Al (DBM) $_3$ and the hole-transport material. The exciplex formation was evidenced by the measurement of the photoluminescence spectra and lifetimes of Al (DBM) $_3$, PVK and an equimolar amount of mixture of Al (DBM) $_3$ and PVK.

• Journal of Mechanical Science and Technology
• /
• v.19 no.12
• /
• pp.2281-2288
• /
• 2005

Because an injected spray development process consists of impinging and free spray in the diesel engine, it is needed to analyze the impinging spray and free spray, simultaneously, in order to study the diesel spray behavior. To dominate combustion characteristics in diesel engine is interaction between injected fuel and ambient gas, that is, process of mixture formation. Also it is very important to analyze liquid and vapor phases of injected fuel on the investigation of mixing process, respectively and simultaneously. Therefore, in this study, the behavior characteristics of the liquid phase and the vapor phase of diesel spray was studied by using exciplex fluorescence method in high temperature and injection pressure field. Finally, it can be confirmed that the distribution of vapor concentration is more uniform in the case of the high injection than in that of the low injection pressure.