• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.1
• /
• pp.69-79
• /
• 2008

Prediction of ground condition ahead of tunnel face might be the most important factor to prevent collapse during tunnel excavation. In this study, a non-destructive method to evaluate the phase velocity in model rock mass using wavelet transform of surface wave was proposed aiming at ground condition assessment ahead of tunnel face. Model tests using gypsum as a rocklike material composed of two layers were performed. A Piezoelectric actuator with frequencies ranging from 150 Hz to 5 kHz was selected as a harmonic source. The acceleration history was measured with two accelerometers. Wavelet transform analysis was used to obtain the dispersion curves from the measured data. The experimental results showed that the near-field effects can be neglected if the distance between two receivers is chosen to be three times the wavelength. A simple inversion method using weighted factor based on the normal distribution was proposed. The inversion results showed that the predicted phase velocity agreed reasonably well with the measured one when the wavelength influence factor was 0.2. The depth of propagation of surface wave was from 0.42 to 0.63 times the wavelength. The range of wavelength varying with phase velocity in dispersion curve matched well with that estimated by inversion technique.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.4
• /
• pp.457-471
• /
• 2015

A domestic cutterhead with the diameter of 3.6 m was designed and manufactured in this study. Then, it was attached to an existing earth-pressure balanced shield TBM to excavate a cable tunnel with the length of 1,275 m. Especially, the procedures for TBM cutterhead design and its corresponding performance prediction were also summarized. From field data analyses of the refurbished shield TBM, its maximum advance rate was recorded as 14.4 m/day. Penetration depths of disc cutters were found to be approximately 4 mm/rev, which is equal to the maximum penetration depth designed for the strongest rock strength condition in the target tunnel. Every TBM operating thrust and cutter normal force during TBM driving was much smaller than their corresponding maximum capacities. When cutter acting forces recorded in the field were analyzed, their prediction errors by the CSM model were very high for weak rock conditions. In addition, rock strength showed very close relationships with cutter normal force and penetration depth.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.10
• /
• pp.5-16
• /
• 2015

Considering the conversion of the Korea Construction Standards to Limit State Design (LSD), we analyzed the resistance bias factor for pullout resistance, as a part of the development of the Load and Resistance Factor Design (LRFD) for soil nailing; very few studies have been conducted on soil nailing. In order to reflect the local characteristics of soil nailing, such as the design and construction level, we collected statistics on pullout tests conducted on slopes and excavation construction sites around the country. In this study a database was built based on the geotechnical properties, soil nailing specifications, and pullout test results. The resistance bias factors are calculated to determine the resistance factor of the pullout resistance for gravity and pressurized grouting method, which are the most commonly used methods in Korea; moreover, we have relatively sufficient data on these methods. We found the resistance bias factors to be 1.144 and 1.325, which are relatively conservative values for predicting the actual ultimate pullout resistance. It showed that our designs are safer than those found in a research case in the United States (NCHRP Report); however, there was an uncertainty, $COV_R$, of 0.27-0.43 in the pullout resistance, which is relatively high. In addition, the pressurized grouting method has a greater margin of safety than the gravity grouting method, and the actual ultimate pullout resistance determined using the pressurized grouting method has low uncertainty.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.3
• /
• pp.51-60
• /
• 2013

The slime, deposited in the bored pile due to falling soil particle, reduces the bearing capacity of bored pile and thus the stability of construction also decreases. The weight pendulum and iron have been used for estimating the slime thickness based on the subjective judgment and thus the previous method has a limitation of reliability. The objective of this paper is to suggest the method for estimating the slime thickness by using characteristics of electrical resistivity as scientific method. The temperature-compensation resistivity probe (TRP), which has a conical shape and the diameter of 35.7mm, is applied to the measurement of the electrical resistivity in the borehole during penetration. The field tests are carried out for estimating the slime thickness in the application site of bored pile. The slime thickness is calculated through the difference between excavation depth of borehole and measured data. Furthermore, the laboratory tests are also conducted for investigating effects of casing, time elapsing and relative density by using the specimen of slime. The laboratory test supporting the suggested method is reasonable for determining the slime depth. The paper suggests that the electrical resistivity method may be a useful method for detecting slime thickness and the method is expected to be applicable to various sites of bored piles.

• Journal of Conservation Science
• /
• v.28 no.2
• /
• pp.119-129
• /
• 2012

Excavated textiles provide very important research data on the costume culture of the Joseon dynasty. In particular, dyed textiles are indispensable for textile conservation research and for restoration of remains as well as for general costume culture research. Unfortunately, a prolonged burial environment causes the colors to change and gradually fade after excavation. Therefore, it is very difficult to identify the original color. In this study, natural dyed samples of red, yellow, purple and blue were prepared and analyzed using HPLC-PDA. Dyes of colorants extracted from excavated textile remains were analyzed by HPLC. In addition, mordants were analyzed using (SEM-EDX) in order to estimate the original color. The 16~17th Century's three samples were analyzed, sample 1, and 2 from Eunjin Song's Song Mun-Chang excavated at the Songchon-dong in Daejeon, and sample 3 from Yeosan Song's Song, Hee-Jong excavated at the Mokdal-dong in Daejeon. From the HPLC results, alizarin, purpurin, and indigo were detected on sample 1, alizarin and purpurin on sample 2, ellagic acid and indigo on sample 3. Therefore they were dyed with madder and indigo (sample 1), madder (sample2), pomagranted and indigo (sample 3). Al mordant was identified on three samples.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6C
• /
• pp.203-212
• /
• 2011

This paper investigates the caharactheristics of the earth pressure magnigue and distribution in jointed rockmass for a safe and economic design and construction of earth retaining structures installed in rock stratum. For this purpose, this study will first investigate the limitations and problems of the existing earth pressure studies and then to overcome them th study will conduct the discontinuum numerical parametric studies based on the Discrete Element Method (DEM), which can consider the joint characteristics in rock stratum. The controlled parameters include rock type and joint conditions (joint shear strength and joint angle), and the magnitude and distribution characteristics of earth pressure have been investigated considering the interactions between the ground and the retaining structures. In addition, the comparison between the earth pressures induced in rock stratum and Peck's earth pressure for soil ground has been carried out. From the comparison, it is found that the earth pressure magnitude and distribution in jointed rockmass has been highly affected by rock type and joint condition and has shown different characteristics compared with the Peck's empirical earth pressure. This result would hereafter be utilized as an important information and a useful data for the assessment of earth pressure for designing a retaining structures installed in jointed rockmass.

• Economic and Environmental Geology
• /
• v.46 no.2
• /
• pp.93-104
• /
• 2013

Daejiguksaptapbi (Tapbi) is a memorial stele which is inscribed with personal history of a state preceptor, Daejiguksa Beopkyeong. The Tapbi comprises tortoise-shaped pedestal, dragon top and body stone, and the body stone is remained in 255 pieces by excavation in Samcheonsaji temple site of Seoul. The Tapbi is composed of tuffaceous breccia for the body, coarse-grained pink feldspar granite for the pedestal and fine-grained granite for the top. As a result of geological survey to find a rock provenance of the Tapbi rock, the tuffaceous breccia is found in the banks of Gangwha straits, and the pink feldspar granite and fine-grained granite are found around the temple site in Mt. Bukhansan. Each rock shows similarities to the Tapbi in lithology and mineralogy. Also, geochemical data of major, some trace and rare earth elements verify their cognation in each rock type. It can be interpreted that the provenance of the body stone is distant as Gangwha area, and the provenance of the pedestal and top stones are near the temple site. The results can be utilized to restore the Tapbi by using the same rocks.

• Journal of Korean Society on Water Environment
• /
• v.32 no.5
• /
• pp.442-449
• /
• 2016

The goal of this study is to provide basic data to establish a foundation for the provision of safe drinkable water. The raw water of natural mineral water was analyzed to determine the quantities of anions (F^-, Cl^-, NO_3-N^-, and SO₄^2- ) and cations (Ca²⁺, K⁺, Mg²⁺, and Na⁺) during the former and latter half of 2016. Analysis of the current quality of the raw water of natural mineral water among domestic manufacturers showed average anions contents of 0.46mg/L of fluorine, 8mg/L of chlorine ion, 1.5mg/L of nitrate nitrogen, and 12mg/L of sulfate ion. While the fluorine content was greater than the water quality criterion of 2.0mg/L at four points, the fluorine level was overall stable. The average cations contents included 21.3mg/L of calcium, 1.0mg/L of potassium, 3.4mg/L of magnesium, and 9.6mg/L of sodium. The chemical characteristics were compared among the major ions, and the results are presented in a piper diagram. The content ratio of cations was in the order of Ca²⁺> Na⁺>Mg²⁺>K⁺, whereas that of anions was in the order of SO₄^2->Cl^->NO_3-N^->F^-. While the cations were slightly scattered, the anions were generally concentrated except for at a few points. The Ca-Na-HCO₃ type was dominant overall in water sources from diorite, gneiss, and granite, while the Na-Mg-Ca-HCO₃-Cl type was dominant in basalt sources. Mineral water manufacturers source their water under various conditions, including in-hole casing, excavation depth, and contact state of bedrock; even within the same rocky area, some differences in the water quality type can occur. When the depth of the water source was taken into account, the mean anions contents of F^-, Cl^-, NO_3-N^-, and SO₄^2- were similar, with no significant differences according to depth. Of the cations, K⁺ and Na⁺ showed no significant differences across all the tubular wells, whereas Ca²⁺ and Mg²⁺ decreased in content with depth.

• Journal of the Korean Geophysical Society
• /
• v.6 no.1
• /
• pp.13-23
• /
• 2003

Dipole-dipole resistivity and ground penetrating radar(GPR) surveys were performed on an abandoned landfill site filled with asbestos containing material. The main purpose of the study was to estimate spatial extension and volume of the landfill for evaluting the cost for developing appropriate remedial alternatives. Assuming that the bedrock is within 10 m depth, dipole spacings of 2, 2.5 and 5m were set for six survey lines for resistivity measurements. For More detailed information, GPR suvey using 225 Mhz antenna was carried out for twelve survey lines for the shallower information. DC resistivity structures showed few tens ~ hundreds ohm-m for the landfill or alluvial laver, and 1,000~ 5,000 ohm-m for the bedrock. The depth to bedrock is found out to be approximately 5m. GPR survey results represented very clear reflection and/or diffraction events from the boundaries as well as from the blocky construction wastes. With high-resolution GPR survey, depth of the bedrock was resolved up to 2m, which in turn, could be a good indicator for estimating the volume of the landfill. Those depths of bedrock were confirmed by backhoe excavation data for 13 sites. The total area and volume of the landfill were to be approximately 3,953 .$m^2$ and 4,033 $m^3$, respectively.

• The Korean Journal of Quaternary Research
• /
• v.18 no.1 s.22
• /
• pp.1-20
• /
• 2004

A geoscientific research was performed on 12 samples of comb-pattern potteries which were excavated at Daecheonri neolithic site, Korea. The texture and compositions of 12 potteries and surrounding metrix of soil and rocks were compared with the help of petrographic microscope, XRD and REE data. As to the manufacturing techniques thick potteries are caused by the amount and number of coarse grains which are assumed to be added shards when their distributional pattern are considered. DC1, DC3, DC 7 and DC11 samples have clearly oriented textures, and the orientation of vesicles in DC3 and DC11 samples arranged in the same direction with those on the pottery surface. This indicates the use potter's wheel technique in manufacturing potteries. Burning temperature is assumed over $800^{/circ}C$, particularly under reduction environment. As to the source, raw materials of pottery matrix are derived from the bottom of excavation site, or in an extracted outcrop of the northwestern foothill from site, while the shard materials are very similar with those extracted from sandy loams near sites. Finally any use pattern of pottery may control the pottery thickness, shard addition, and matrix selection.