• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.10 s.89
• /
• pp.944-951
• /
• 2004

In this paper, we proposed the method of the characteristic impedance and effective dielectric constant calculations of the shielded microstrip line with ground aperture using conformal mapping method. This method has advantages that can calculate the transmission parameters without using any other numerical method because present the closed form equations. First of all, we supposed the signal propagate with the microstrip mode(Quasi-TEM) and calculated the capacitance divide by three sections and calculated the characteristic impedance and effective dielectric constant using calculated capacitances. From the HFSS simulation result, calculated result was very similar to the simulation result within the five percent error range.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.11
• /
• pp.924-927
• /
• 2017

This paper presents a 6~18 GHz 8-bit true time delay (TTD) circuit. The unit delay circuit is based on m-derived filter with relatively constant group delay. The designed 8-bit TTD is implemented with two single-pole double-throw (SPDT) switches and seven double- pole double-throw (DPDT) switches. The reflection characteristics are improved by using inductors. The designed 8-bit TTD was fabricated using $0.18{\mu}m$ CMOS. The measured delay control range was 250 ps with 1 ps of delay resolution. The measured RMS group delay error was less than 11 ps at 6~18 GHz. The measured input/output return losses are better than 10 dB. The chip consumes zero power at 1.8 V supply. The chip size is $2.36{\times}1.04mm^2$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.7
• /
• pp.1033-1038
• /
• 2013

Petrochemical complex has been a lot of research for the development of a more mature product and analysis for mid-process and finished products is essential in these process. But these analyzes are still by hand work samples being manufactured in many parts. Moreover they are exposed to hazardous chemical and such as the analysis is being made in a very poor working conditions. In this paper, in order to solve such problems the multi control system has been developed for the automated analysis. In addition, the organic behavior of these systems and the development of a program for the automated applied, and throughout the experiment to verify the reliability of this device for the accuracy of the dosing pumps for the standard solution prepared with a range of error of ${\pm}0.01m{\ell}$ was able to get a very good experimental results.

• Journal of the Korean Data and Information Science Society
• /
• v.23 no.4
• /
• pp.657-663
• /
• 2012

There are very small values and/or very big values which get out of the normal range for survey data in various fields. The reasons of occurrence for outlier are two. One of them is the error in process of data input and the other is the strange response of the respondent. If the data has outliers, then the summary statistics such as the mean and the variance produce misleading information. Therefore, researcher should be careful in detecting the outlier in data. In particular, it is very important problem for clinical fields because the cost of experiment is very high. This article introduce the Grubb test and Cochran test to detect outliers in the data and we apply this method for clinical data.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.501-512
• /
• 2018

Radio frequency identification (RFID) sensor tag provides several advantages including battery-less operation and low cost, which are suitable for long-term monitoring. This paper presents a self-powered RFID temperature sensor tag for online temperature monitoring in substation. The proposed sensor tag is used to measure and process the temperature of high voltage equipments in substation, and then wireless deliver the data. The proposed temperature sensor employs a novel phased-locked loop (PLL)-based architecture and can convert the temperature sensor in frequency domain without a reference clock, which can significantly improve the temperature accuracy. A two-stage rectifier adopts a series of auxiliary floating rectifier to boost its gate voltage for higher power conversion efficiency. The sensor tag chip was fabricated in TSMC $0.18{\mu}m$ 1P6M CMOS process. The measurement results show that the proposed temperature sensor tag achieve a resolution of $0.15^{\circ}C$/LSB and a temperature error of $-0.6/0.7^{\circ}C$ within the range from $-30^{\circ}C$ to $70^{\circ}C$. The proposed sensor tag achieves maximum communication distance of 11.8 m.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.1
• /
• pp.7-13
• /
• 2005

In this paper, we propose the time synchronization module on fiber optic repeater to use optic line delay for obtaining time synchronization between up-link and down-link, in the 2.3 GHz WiBro network using TDD/OFDM (Time Division Duplex/Orthogonal Frequency Division Multiplexing) Generally, when we use fiber optic repeater to remove the shade area, it occurs transmission delay which is caused by optic transmission between RAS (Radio Access Station) and fiber optic repeater and inner delay of fiber optic repeater. Because the WiBro system is adopting a TOO method and there exists the difference of switching time which is caused by these delay between up-link and down-link, it occurs ISI (Inter Symbol Interference), ICI (Inter Carrier Interference). These interference results in the reduction of the coverage. And the inconsistency between Up-Link and Down-Link switching time maybe gives rise to the interruption of communication. In order to prevent these cases, we propose synchronization module using analog optic line delay as the one of synchronizing up-link and down-link. And we propose the consideration factor for the designing time synchronization module and the feature of optic line of analog method. The measurement result of optic line time synchronization module of structure proposed is as follows, the delay error of $0.5{\mu}g$ and the insertion loss value below maximum 4.5dB in range of $0{\sim}40{\mu}s$. These results fully meet the specification of WiBro System.

• Journal of KIISE:Databases
• /
• v.30 no.5
• /
• pp.464-475
• /
• 2003

few sample objects and compressed histogram information of image databases. The histogram information is used to estimate the selectivity of spherical range queries and a small number of sample objects is used to compensate the selectivity error due to the difference of the similarity measures between meta server and local image databases. An extensive experiment on a large number of image data demonstrates that our proposed method performs well in the distributed heterogeneous environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37C no.10
• /
• pp.933-939
• /
• 2012

In general, the three-dimensional(3D) coordinates of the manufactured ship blocks are measured using the laser measuring equipment by ship engineers. But, many deflections between the measured coordinates in manufactured step and the designed coordinates in the design step are occurred because of the measuring process of ship blocks manually. Thus, the ship engineer should conform the consistency between the measured coordinates and the designed coordinates step by step, and it largely causes the loss of manpower and time. In this paper, the automated pattern matching algorithm of 3D coordinates for quality control in ship blocks is suggested in order to solve this problem, and the performance of the algorithm is analyzed using the 3D coordinates simulation software developed by our research laboratory. The coordinates matching rate of the measured coordinates in the single/multi ship block(s) is about 90.2% under the tolerated distance error range is 20~25cm.

• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.369-380
• /
• 2013

Direct torque control based on space vector modulation (SVM-DTC) protects the DTC transient merits. Furthermore, it creates better quality steady-state performance in a wide speed range. The modified method of DTC using SVM improves the electrical magnitudes of asynchronous machines, such as minimizing the stator current distortions, the stator flux with electromagnetic torque without ripple, the fast response of the rotor speed, and the constant switching frequency. In this paper, the proposed method is based on two new control strategies for direct torque control with space vector modulation. First, fuzzy logic control is used instead of the PI torque and a PI flux controller to minimizing the torque error and to achieve a constant switching frequency. The voltages in the direct and quadratic reference frame ($V_d$, $V_q$) are achieved by fuzzy logic control. In this scheme, the switching capability of the inverter is fully utilized, which improves the system performance. Second, the close loop of stator flux estimation based on the voltage model and a low pass filter is used to counteract the drawbacks in the open loop of the stator flux such as the problems saturation and dc drift. The response of this new control strategy is compared with DTC-SVM. The experimental and simulation results demonstrate that the proposed control topology outperforms the conventional DTC-SVM in terms of system robustness and eliminating the bad outcome of dc-offset.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.9-16
• /
• 1996

This paper deals with the capacitive voltage divider which can measure a transient voltages generated by operating a high voltage impulse generator. The transient voltage measuring system using the capacitive electric field sensor consists of the planar-type electric field sensor having a fast response characteristic and the wide-bandwidth voltage follower, and the input impedance of which is extremely high, about $10^{12}{\Omega}$. In order to analyze the response characteristics to a step input, the newly developed calibration method is proposed, and the error of voltage dividing ratio associated with set-up condition is investigated. Also the optimal set-up condition that is to be maintained within the range of 0.5 % is taken. From the calibration experiment, the frequency bandwidth of the transient voltage measuring system whose response time to a step input is about 15.8 ns, is from 6.37 Hz to 27.3 MHz. Therefore it is possible to measure the commercial frequency voltages as well as the transient over voltages without signal distortions.