• Computers and Concrete
• /
• 제3권5호
• /
• pp.357-373
• /
• 2006

The concepts of four parameters of nominal water-cement ratio, equivalent water-cement ratio, average paste thickness, fly ash-binder ratio were introduced. It was verified that the four parameters and the mix proportion of mortar can be transformed each other. The behaviors (strength, workability, et al.) of mortar primarily determined by the mix proportion of mortar now depend on the four parameters. The prediction models of strength and workability of mortar were built based on artificial neural networks (ANNs). The calculation models of average paste thickness and equivalent water-cement ratio of mortar can be obtained by the reversal deduction of the two prediction models, respectively. A mortar mix proportion design algorithm was proposed. The proposed mortar mix proportion design algorithm is expected to reduce the number of trial and error, save cost, laborers and time.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.887-890
• /
• 2001

In end milling process the underformed chip thickness and the cutting force components very periodically with phase change of the tool. In this study, up end milling process is transformed to the equivalent oblique cutting. The varying underformed chip thickness and the cutting force components in end milling process are replaced with the equivalent average ones. Then it can be possible to analyze the chip-tool friction and shear process in the shear plane of the end milling process by the equivalent oblique cutting mode. According to this analysis, when cutting Inconel 718.61% of the total energy is consumed in the shear process and the balance is consumed in the friction process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.902-906
• /
• 2000

In end milling process the undeformed chip thickness and the cutting force components vary periodically with phase change of the tool. In this study, up end milling process is transformed to the equivalent oblique cutting. The varying undeformed chip thickness and the cutting force components in end milling process are replaced with the equivalent average ones. Then it can be possible to analyze the chip-tool friction and shear process in the shear plane of the end milling process by the equivalent oblique cutting model. According to this analysis, when cutting SM45C steel. 82% of the total energy is consumed in the shear process and the balance is consumed in the friction process.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.854-855
• /
• 2013

As an unique acoustic characteristic of a Korean bell. beat phenomenon is a periodic repetition of strong and weak sounds. Beat sounds good when it is clear and it has a proper period, however, it is not easy to satisfy these two conditions simultaneously. In this study, we propose a beat tuning method to satisfy these two conditions, by using an equivalent bell model. First, we construct an equivalent bell which has the same beat property with the 1st beat of a real bell and we investigate the change of mode pair by finite element analysis, when thickness of the bell is locally decreased at $22.5^{\circ}$ from the striking point. From the analysis result, minimum thickness reduction amount is determined to make a clear and strong beat.

• Journal of Periodontal and Implant Science
• /
• 제25권1호
• /
• pp.67-75
• /
• 1995

The progress of periodontal disease and the wound healing process after treatment result in alveolar bone bone change. So, detection of it is very important in the diagnosis and the radiograph of periodontal disease. Various effects have been made to assess the subtle alveolar bone change and digital subtraction radiography (DSR) has been reported to be the best method in evaluating it qualitatively and quantitatively. The present study was performed to estimate the detectable alveolar bone change qualitatively with digital subtraction radiography. For the in vitro study, 10 intraoral standard radiographs were taken from porcine dry mandible which a rectangular cortical bone chip of 0.1mm to 1.0mm thickness with 0.1mm increment was attached on the buccal surface. The radiographs without and with bone plates were reviewed at the same time by 10 observers and requested to detect the presence of cortical bone plates. Digital Subtraction radiograph was reviewed subsequently by using the DSR system(digital converter-256 grey-levels,DT 2851,Data Translation Co., U.S.A;IBM 386 ; CCD camera, FOTOVIX, Tamrom Co., Japan). The detectable thickness of cortical bone plate was O.4mm on the intraoral radiograph and 0.2mm on the subtaction images. For the human study, radiographs were taken from patients by using intraoral film holding device and aluminum reference wedge before and 3 month after bone graft and 1 week after osteoplasty. The grey level change was estimated in the subtraction images and calculated to aluminum equivalent thickness. The grey level of the grafted site was higher that that of healthy controls. Average grey levels of change on healthy controls were O.48mm aluminum equivalent. However, the amount of changes in grafted sites were 1.87mm aluminum thickness equivalent and in the site of osteoplasty were -1.49mm aluminum thickness equivalent. In conclusion, digital subtraction radiography was more effective in detecting as subtle change of alveolar bone than intraoral standard radiography. With the aid of quantitative analysis of digital subtraction radiography, alveolar bone resorption of apposition can be estimated during diagnosis and treatment of periodontally diseased patients.

• 한국산학기술학회논문지
• /
• 제12권1호
• /
• pp.32-37
• /
• 2011

본 연구에서는 구조해석을 통하여 차체의 전복 시에 있어서의 차체의 두께에 따른 변형량과 응력 변화를 고찰하여 보았다. 차체의 두께가 5t인 자동차에서는 2초일 때에 차체의 오른쪽 천장에서 7.5024mm의 최대변형이 일어났으며, 차체의 왼쪽 밑 부분에서 113.69 MPa의 최대응력을 받았다. 차체의 두께가 10t인 자동차에서는 2초일 때에 차체의 오른쪽 천장에서 1.2557mm로 최대의 변형이 일어났으며 차체의 왼쪽 밑 부분에서 15.134 MPa의 최대응력이 발생했다. 차체의 두께가 15t인 자동차에서는 2초일 때에 0.42529mm로서 차체의 오른쪽 천장에서 최대의 변형이 일어났으며 응력은 2초일 때에 차체의 왼쪽 밑 부분에서 4.405MPa의 최대응력이 작용되었다. 두께가 15mm보다 커지는 경우에는 시간에 따른 응력 및 변형율의 분포가 고르게 나타나고 있어 설계의 안전성을 보이고 있다.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.188-195
• /
• 2004

In this paper we analyzed the mechanical behavior with respect to the thickness variation of elastic foundation(fatty tissue) in end-to-end anastomosis. This study considered the preliminary deformed shape induced by suturing in the anastomosis of coronary artery and PTFE with different diameters using simplified suturing model and the fatty tissue surrounding heart and coronary artery for more accurate result using finite element method. Area compliance(CA) was used to analyze the final deformed shape of the anastomotic part with respect to the thickness variation of fatty tissue under mean blood pressure, 100mmHg(13.3㎪). And Equivalent and circumferential stresses in the anastomosis were also analyzed with respect to the change of initial diameter ratio( $R_1$) and fatty tissue thickness( $T_{F}$). The results obtained were as follows : 1 When the elastic foundation, assumed to be incompressive material, surrounded the grafts in anastomosis, the compliance mismatch of artery and PTFE was reduced by 47 -72%. 2. As the initial diameter ratio( $R_1$) became larger, the higher difference of compliance was induced in spite of elastic foundation surrounding grafts. 3. The maximum nondimensional circumferential stress is twice or three times as high as the maximum nondimensional equivalent stress in the anastomotic part.t.

• Steel and Composite Structures
• /
• 제16권6호
• /
• pp.657-679
• /
• 2014

This paper describes a series of compression tests performed on cold-formed steel channel sections with perforations in the web (thermal studs) fabricated from a galvanized steel plate whose thickness ranged from 1.0 mm to 1.6 mm and nominal yield stress was 295 MPa. The structural behavior and performance of thermal studs undergoing local, distortional, or flexural-torsional buckling were investigated experimentally and analytically. The compression tests indicate that the slits in the web had significant negative effects on the buckling and ultimate strength of thin-walled channel section columns. The compressive strength of perforated thermal studs was estimated using equivalent solid channel sections of reduced thickness instead of the studs. The direct strength method, a newly developed and adopted alternative to the effective width method for designing cold-formed steel sections in the AISI Standard S100 (2004) and AS/NZS 4600 (Standard Australia 2005), was calibrated to the test results for its application to cold-formed channel sections with slits in the web. The results verify that the DSM can predict the ultimate strength of channel section columns with slits in the web by substituting equivalent solid sections of reduced thickness for them.

• 한국광학회지
• /
• 제23권1호
• /
• pp.17-22
• /
• 2012

등가렌즈는 전체굴절능과 주변광선에 대한 근축광학적 특성은 같지만 축상두께가 다른 렌즈이다. 이 연구에서는 두꺼운 렌즈를 등가렌즈로 변환하는 해석적인 방법에 대하여 연구하였고, 변환조건이 2차방정식의 해로서 주어짐을 보였다. 모든 두꺼운 렌즈는 유일해인 경우를 제외하면 이 2차방정식의 두 실근중의 하나이기 때문에 반드시 공액해가 1개 존재한다. 이 공액해는 축성 두께와 근축광학적 특성은 같지만 모양과 수차특성은 다르다. 예제 렌즈의 등가렌즈 변환을 통하여 등가렌즈와 이에 대응하는 공액해의 특성을 살펴보았다.

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.707-715
• /
• 1994

This study presents thickness optimization for the pressure vessel domes subject to internal pressure and axial force simultaneously. The considered typical pressure vessel domes are ellipsoidal and tori-spherical domes with skirt and nozzle part. These pressure vessel domes under loading have higher stress concentration on geometric discontinuity parts. Therefore, thickness optimization of axi-symmetric pressure vessel domes is essentially concerned on minimizing this stress concentration. The objective function is minimization of weight of pressure vessel dome. The design variable is thickness of dome and cylinder. Considered constraint is Von Mises equivalent stress. In the optimization procedure, ANSYS code is used. The equivalent and hoop stress of original shape domes are compared with those of optimal shape domes. And optimal thicknesses for pressure vessel domes are presented.